![]() |
my profile |
register |
faq |
search upload photo | donate | calendar |
|
![]() |
#1 |
User
Join Date: Apr 2014
Location: California and Nevada
Posts: 98
Thanks: 63
Thanked 67 Times in 29 Posts
|
![]()
Gentlemen,
I just received my proof marked luger tool. It is 1.9 mm thick and has what appears to be a three lobbed crown over a gothic letter "G". It has some patina. Would this be a good match for my 1912 Erfurt or would it go more with a DWM pistol and is this a common or rare proof mark? Thank you, Ricardo |
![]() |
![]() |
![]() |
#2 |
Moderator
Lifetime Forum Patron Join Date: Jun 2002
Location: Arizona/Colorado
Posts: 7,764
Thanks: 4,871
Thanked 3,110 Times in 1,429 Posts
|
![]()
Ricardo, Here's a little camera tip. White backgrounds reflect light into your lens and on auto setting this closes the lens..too much light. Consequently you tool does not show but as a black blob. Pick up your tool, hold it in your hand in front of the lens..move around in the room until the light is perfect on the tool in your viewfinder. SNAP! Perfect pic of the marking.
__________________
Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 lugerholsterrepair@earthlink.net 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) ![]() "For those who Fight For It, Life has a flavor the protected will never know." |
![]() |
![]() |
![]() |
#3 |
User
Join Date: Apr 2014
Location: California and Nevada
Posts: 98
Thanks: 63
Thanked 67 Times in 29 Posts
|
![]()
Jerry,
Thank you for the suggestion. Hopefully the attached pictures are a bit clearer. Regards, Ricardo |
![]() |
![]() |
![]() |
#4 |
User
Join Date: Apr 2014
Location: California and Nevada
Posts: 98
Thanks: 63
Thanked 67 Times in 29 Posts
|
![]()
A correction on the tool thickness as I previously measured it at the wrong location. It is actually 2.5 mm thick.
|
![]() |
![]() |
![]() |
#5 |
User
Join Date: Jun 2009
Location: Germany
Posts: 517
Thanks: 0
Thanked 411 Times in 160 Posts
|
![]()
That is an Erfurt tool and would match your Erfurt Luger if one of the acceptance marks on the Luger has the C/G.
Erfurt tools are always “unblued/ blank” and have always a 3 lobe crown while DWM tools are "blued" and have mostly a 4 lobe crown. Erfurt and DWM tools have a different shape. I add a pic to show the differences... |
![]() |
![]() |
![]() |
#6 |
User
Join Date: Apr 2014
Location: California and Nevada
Posts: 98
Thanks: 63
Thanked 67 Times in 29 Posts
|
![]()
Sir,
Yes, my Luger also displays the crown over "G" acceptance mark. Is this tool with the C/G marking considered rare or one of the more common tools? I ended up paying just a bit over a hundred dollars for it which is more than I wanted and expected to pay for a tool but it was from a reputable seller with whom I have dealt with in the past. As these are often faked, I was hesitant to pursue other sources. Regards, Ricardo |
![]() |
![]() |
![]() |
#7 |
User
Join Date: Jun 2009
Location: Germany
Posts: 517
Thanks: 0
Thanked 411 Times in 160 Posts
|
![]()
It´s a rare tool.
|
![]() |
![]() |
The following member says Thank You to klaus 3338 for your post: |
![]() |
#8 |
Patron
LugerForum Patron Join Date: Jan 2012
Location: Virginia
Posts: 127
Thanks: 166
Thanked 129 Times in 63 Posts
|
![]()
Klaus:
Appreciation the explanation and picture. Ron |
![]() |
![]() |
![]() |
|
|