New FAQ - Update suggestions and Corrections Thread - Page 4

sheepherder · 12-31-2019, 12:08 AM

Quote:

Originally Posted by mrerick

That's when I did the last update. I'll be working on it again soon. I try and update this once or twice a year, and keep notes on what to add here in this post.

So, the downloadable .PDF FAQ isn't actually updated??? It's still the August FAQ??? With 'updates' linked on this page???

Works for me...

DonVoigt · 12-31-2019, 10:28 AM

Marc,
you are doing a great job.
I believe you are "assembling" a book that could be a stand alone guide.

mrerick · 05-23-2020, 07:47 PM

Possible update. looking for source of info:

Stamping sequence on Lugers
Since this topic has been coming up lately I thought I would post my understanding of the Luger acceptance mark sequence.

I believe that the stamps were applied at different stages in tthe production process startingwith the fram hardening stamp. The sequence would insure that the military inspector could look at a pistol in the factory and know that it had the proper inspection for that point in the process

The inspection stamps were applied in the following sequence:

The reciever is hardened and presented to the inspector

The first acceptance mark allowing the parts to be assebled to the receiver is stamped and the date was stamped into the receiver top at the same time.The placement of this stamp on the reciever determines the location of the rest of the stamps as they all go to the right of this initial hardening stamp. When looking at acceptance stamps on imperial lugers you can see some variation in the spacing. This is more pronounced in the 1916 to 1918 years.

After this initial hardness acceptance, pistol is completely assembled and again presented to the inspector

2. The second acceptance mark, Pistol ready for testing is applied to the right of and adjacent to the hardness proof and the complete serial number is applied at the same time.

3. The visually accepted complete pistol is presented to the inspectors for proof firing and two proof load cartridges are fired. The test proof eagle was applied forward of the inspection stamps. This indicated that the pistol had fired two overloaded test cartridges without damage.

4. The final inspectors measure the Pistol for acceptance after test firing; this indicated that the pistol had passed its post firing inspection. The barrel land diameter was added to the bottom of the barrel. This final inspection stamp was applied to the left of the test proof eagle and to the right of the hardness and assembly acceptance marks.

This results in the inspection stamps being located on the right receiver as follows (left to right).
1. Hardness furthest to the left.
2. Assembled adjacent to 1.
3.Final acceptance adjacent to 2.
4. Above, test proof located furthest to the right near barrel

I believe that at one point the Imperial requirements for this sequence were posted on the forum but I can no longer find them.

Some writers have indicated that all four stamps were applied at one time. I do not believe this to be the case. First of all it would be an affront to German efficiency. Second the process i described, and believe I read once upon a time serves to prevent an un heat treated frame fom getting into the assembly line, prevents an un-inspected pistol form being presented for proof, and prevents an on-prooved pistol from going through final inspection.

If someone has documentation describing this I would be grateful

mrerick · 11-04-2020, 10:07 AM

Update FAQ to add discussion of M1900 flat springs:

http://forum.lugerforum.com/showthread.php?t=40701

mrerick · 01-15-2021, 03:13 PM

Add discussion of Luger upper as a firearm:

http://forum.lugerforum.com/showthread.php?t=40845

Heinz · 01-15-2021, 06:10 PM

Thanks for all the work you do to keep this great resource available.

mrerick · 06-27-2021, 10:20 AM

Add discussion of magazines:

http://forum.lugerforum.com/showthread.php?t=40440

Pics in thread. Perhaps add pics of FXO mags

gunnertwo · 06-27-2021, 06:42 PM

Many thanks!

G2

mrerick · 07-01-2021, 05:09 PM

From Heinz,

I was looking at the FAQ on cold blue. I believe it has an error. The copper compound with the smell is copper selenide, the same chemical that gives garlic its smell. Commercial cold-bluing compounds contain selenium often as selenious acid. The chemical reaction with the copper sulfate in the bluing solution when applied to iron, forms a copper selenide black plating on the metal

Edward Tinker · 07-01-2021, 05:17 PM

when you update, can we update the first posting and the last with a same copy?

mrerick · 07-01-2021, 09:12 PM

Yes - the 2019 version is the latest at this point.
Where are the two postings? (links)?

mrerick · 07-06-2021, 10:30 AM

Article on Luft Waffen Amts (BAL):

Edward Tinker · 07-06-2021, 01:52 PM

The sequence of stamping proofs and acceptance is in the smaller book by Gortz (in english) on markings (German Small Arms Markings)

mrerick · 07-07-2021, 10:16 AM

I don't have a copy, can you provide?

mrerick · 07-21-2021, 05:54 PM

S/42 font formats on toggles 1934-1939

mrerick · 09-26-2022, 10:38 AM

Grip screw details:

https://forum.lugerforum.com/showpos...40&postcount=3

mrerick · 12-20-2023, 06:36 PM

List of Magazine manufacturers:

Discussion at:

https://forum.lugerforum.com/showthr...868#post348868

12-31-2019, 10:28 AM	#62
DonVoigt User Join Date: Apr 2015 Location: near Charlotte NC Posts: 4,681 Thanks: 1,441 Thanked 4,350 Times in 2,040 Posts	Marc, you are doing a great job. I believe you are "assembling" a book that could be a stand alone guide. __________________ 03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie

05-23-2020, 07:47 PM	#63
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	Possible update Possible update. looking for source of info: Stamping sequence on Lugers Since this topic has been coming up lately I thought I would post my understanding of the Luger acceptance mark sequence. I believe that the stamps were applied at different stages in tthe production process startingwith the fram hardening stamp. The sequence would insure that the military inspector could look at a pistol in the factory and know that it had the proper inspection for that point in the process The inspection stamps were applied in the following sequence: The reciever is hardened and presented to the inspector The first acceptance mark allowing the parts to be assebled to the receiver is stamped and the date was stamped into the receiver top at the same time.The placement of this stamp on the reciever determines the location of the rest of the stamps as they all go to the right of this initial hardening stamp. When looking at acceptance stamps on imperial lugers you can see some variation in the spacing. This is more pronounced in the 1916 to 1918 years. After this initial hardness acceptance, pistol is completely assembled and again presented to the inspector 2. The second acceptance mark, Pistol ready for testing is applied to the right of and adjacent to the hardness proof and the complete serial number is applied at the same time. 3. The visually accepted complete pistol is presented to the inspectors for proof firing and two proof load cartridges are fired. The test proof eagle was applied forward of the inspection stamps. This indicated that the pistol had fired two overloaded test cartridges without damage. 4. The final inspectors measure the Pistol for acceptance after test firing; this indicated that the pistol had passed its post firing inspection. The barrel land diameter was added to the bottom of the barrel. This final inspection stamp was applied to the left of the test proof eagle and to the right of the hardness and assembly acceptance marks. This results in the inspection stamps being located on the right receiver as follows (left to right). 1. Hardness furthest to the left. 2. Assembled adjacent to 1. 3.Final acceptance adjacent to 2. 4. Above, test proof located furthest to the right near barrel I believe that at one point the Imperial requirements for this sequence were posted on the forum but I can no longer find them. Some writers have indicated that all four stamps were applied at one time. I do not believe this to be the case. First of all it would be an affront to German efficiency. Second the process i described, and believe I read once upon a time serves to prevent an un heat treated frame fom getting into the assembly line, prevents an un-inspected pistol form being presented for proof, and prevents an on-prooved pistol from going through final inspection. If someone has documentation describing this I would be grateful __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

11-04-2020, 10:07 AM	#64
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	Update FAQ to add discussion of M1900 flat springs: http://forum.lugerforum.com/showthread.php?t=40701 __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

01-15-2021, 03:13 PM	#65
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	Add discussion of Luger upper as a firearm: http://forum.lugerforum.com/showthread.php?t=40845 __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

06-27-2021, 10:20 AM	#67
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	Add discussion of magazines: http://forum.lugerforum.com/showthread.php?t=40440 Pics in thread. Perhaps add pics of FXO mags __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

01-15-2021, 06:10 PM	#66
Heinz User Join Date: Jun 2002 Location: Greenville SC Posts: 1,004 Thanks: 377 Thanked 410 Times in 180 Posts	Thanks for all the work you do to keep this great resource available.

06-27-2021, 06:42 PM	#68
gunnertwo User Join Date: Jan 2010 Location: Nampa, Idaho Posts: 623 Thanks: 826 Thanked 930 Times in 363 Posts	Many thanks! G2

07-01-2021, 05:09 PM	#69
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	cold Blue chemistry From Heinz, I was looking at the FAQ on cold blue. I believe it has an error. The copper compound with the smell is copper selenide, the same chemical that gives garlic its smell. Commercial cold-bluing compounds contain selenium often as selenious acid. The chemical reaction with the copper sulfate in the bluing solution when applied to iron, forms a copper selenide black plating on the metal __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

07-01-2021, 05:17 PM	#70
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,933 Thanks: 2,032 Thanked 4,530 Times in 2,092 Posts	when you update, can we update the first posting and the last with a same copy?

07-01-2021, 09:12 PM	#71
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	Yes - the 2019 version is the latest at this point. Where are the two postings? (links)? __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

07-06-2021, 10:30 AM	#72
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	Article on Luft Waffen Amts (BAL): __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

07-06-2021, 01:52 PM	#73
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,933 Thanks: 2,032 Thanked 4,530 Times in 2,092 Posts	The sequence of stamping proofs and acceptance is in the smaller book by Gortz (in english) on markings (German Small Arms Markings)

07-07-2021, 10:16 AM	#74
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	I don't have a copy, can you provide? __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

07-21-2021, 05:54 PM	#75
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	S/42 font formats on toggles 1934-1939 __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

09-26-2022, 10:38 AM	#76
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	Grip screw details: https://forum.lugerforum.com/showpos...40&postcount=3 __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

12-20-2023, 06:36 PM	#77
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,909 Thanks: 1,374 Thanked 3,110 Times in 1,510 Posts	List of Magazine manufacturers: Discussion at: https://forum.lugerforum.com/showthr...868#post348868 __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.