Luger sights?

Edward Tinker · 03-09-2017, 11:39 AM

Okay, I have picked up a number of front sights over the last few years, and curious to what others think they are?

#1 container said P38
#2 container said 1914
#3 look new made

the rest

others look like possible marbles type - someone said carbine or carbine type (rifle?)

DavidJayUden · 03-09-2017, 01:00 PM

Group 1, second from the right side, appears like something for a K98 rifle. I need a tall front sight blade for my Navy shooter, and learned that the groove size is common to Euro. guns. I still need a tall front sight blade if any of them are available.
dju

DonVoigt · 03-09-2017, 01:24 PM

Ed,
I think they are what you say.
VI is probably for the K98 or similar.

DJU,
K98 sights are available online from the big guys and cheaper than luger sights, and they do fit the dovetail, just need the "wings" cliped to fit!

Well, sometimes you need to do a little needle file work on any dovetail sight to get it to fit well.

Edward Tinker · 03-09-2017, 01:30 PM

Quote:

Originally Posted by DavidJayUden

Group 1, second from the right side, appears like something for a K98 rifle. I need a tall front sight blade for my Navy shooter, and learned that the groove size is common to Euro. guns. I still need a tall front sight blade if any of them are available.
dju

this one?

DavidJayUden · 03-09-2017, 03:02 PM

Ed:
The one you circled is similar to one I bought from Sarco and was called a "K98 tall sight". Sometime send me a photo of your tallest sights and hopefully we can find one taller than what I have because even with that K98 tall sight, my Navy still prints high.
And I'll measure what I have.
dju

Edward Tinker · 03-09-2017, 04:18 PM

David, will do - will put them alongside each other and see which is tallest.

email sent

Diver6106 · 03-10-2017, 04:38 PM

I put a type IV on a 22LR Luger I have that was missing the front sight. It fit fine.

ithacaartist · 03-10-2017, 05:50 PM

Quote:

Originally Posted by Diver6106

I put a type IV on a 22LR Luger I have that was missing the front sight. It fit fine.

David, If you mean an Erma .22 "Luger," I have NOS front sights available for all toggle pistol models, if you wish to maintain original parts on it!

G.T. · 03-10-2017, 06:21 PM

It has been a long and fruitless search for, "just a little taller" Luger front sight blades and / or an alternate type that you can fit without owning a machine shop!

... Variances in dovetail widths and heights, (on both parts) don't help the search much either?...
I have found that, blades for artillery and Navy Lugers are a bit taller than standard, but much pricier as well... doesn't help the shooter much unless you can rob one off of another unit or parts gun, accumulated along your journey...
Mauser K98 sights are too low... and if you use a custom blade from Brownells, you have to completely profile and shape with the tools at hand... small flat file and small three corner file as well... And, it is a time consuming task..
The easiest sight to reshape and might just have the height you need is a #4 P.38 sight... I just recently did one of these for a GTS/T-4 barrel and the results were encouraging... All I did was file both sides so to end up with a sharp point... more sharp then the Luger was originally...
Marbles used to make a #27 gold bead sheared blade, but they were pretty low as I remember?...
That's the limit of what I know so far! And the search continues... Best to all, til...lat'r....GT....

DonVoigt · 03-10-2017, 08:04 PM

This sight is tall, and works fine as set up.
GT sent it to me, he can confirm- but I think it came from Brownell's.

G.T. · 03-10-2017, 10:54 PM

Hi Don, yes! That is the Mauser custom blade from Brownells.... It works out well for you as you have the adj. rear sight mounted on the rear toggle... You would need to lower it some, and profile and shape correctly for a Luger rear sight... But, the main problem with that particular sight is the cost $25.00 each!!!

... That is more then I usually make on most of my barrel projects...

.... (see profitability / feasibility study!

) also, once cut for the Mauser blade.. there is no going back... Neat shooter Don, you need to print that baby on paper and see what you can hold for a group... Inqusitive minds want to know! best to all, til...lat'r...GT....

DonVoigt · 03-10-2017, 11:17 PM

Quote:

Originally Posted by G.T.

Hi Don, yes! That is the Mauser custom blade from Brownells.... It works out well for you as you have the adj. rear sight mounted on the rear toggle... You would need to lower it some, and profile and shape correctly for a Luger rear sight... But, the main problem with that particular sight is the cost $25.00 each!!!

... That is more then I usually make on most of my barrel projects...

.... (see profitability / feasibility study!

) also, once cut for the Mauser blade.. there is no going back... Neat shooter Don, you need to print that baby on paper and see what you can hold for a group... Inqusitive minds want to know! best to all, til...lat'r...GT....

Well, now I really have no excuse not to fire for group. I have had both eyes "fixed" - i.e. cataracts removed and plastic lenses installed!

Now I can actually see the sights and the target at the same time.

Edward Tinker · 03-11-2017, 12:05 AM

That's the five inch right?

My six inch is just too heavy, so it's finicky

. Maybe take a Dremel to the sides

DonVoigt · 03-11-2017, 09:46 AM

Quote:

Originally Posted by Edward Tinker

That's the five inch right?

My six inch is just too heavy, so it's finicky

. Maybe take a Dremel to the sides

Yes, 5"; works fine- but your 6" probably pushes it over the edge.

The numbers below show the weights of the bull barrels vs the "std" navy and artillery. As you can see the 5" is close to the artillery, but the 6" bull is about 2 oz. heavier-therein the problem lies.
4" bull- 6.7
5" bull- 8.4
6" bull- 10.0

std 4"- 3.8
Navy 6"- 5.3
Art 8" - 7.7

Some of these are actual weights, the 4" and 6" bull are calculated from my 5" weight.

Ed-
I could take a couple ounces off your 6" by "thinning" the sides!
Kind of make a "thin bull".

If you want me too just send it!

Edward Tinker · 03-12-2017, 12:18 AM

I might, we'll chat

Ed

Diver6106 · 03-16-2017, 07:44 PM

Lifer- I have a 1913 DWM converted to 22LR, #1057. The barrel is sleeved and the breechblock cut back to the shorter length, with a 22LR seating cut. Then the firing pin was cut flat with a pin drilled and side mounted to it with a whole side cut. But it still needs to have the bottom of the breechblock machined, as in a 22 conversion kit, so it will feed rounds off a conversion kit 22LR mag. As it is it is single shot.

03-10-2017, 06:21 PM	#9
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,528 Thanks: 1,334 Thanked 3,711 Times in 1,014 Posts	Scarcity of tall Luger sights! It has been a long and fruitless search for, "just a little taller" Luger front sight blades and / or an alternate type that you can fit without owning a machine shop! ... Variances in dovetail widths and heights, (on both parts) don't help the search much either?... I have found that, blades for artillery and Navy Lugers are a bit taller than standard, but much pricier as well... doesn't help the shooter much unless you can rob one off of another unit or parts gun, accumulated along your journey... Mauser K98 sights are too low... and if you use a custom blade from Brownells, you have to completely profile and shape with the tools at hand... small flat file and small three corner file as well... And, it is a time consuming task.. The easiest sight to reshape and might just have the height you need is a #4 P.38 sight... I just recently did one of these for a GTS/T-4 barrel and the results were encouraging... All I did was file both sides so to end up with a sharp point... more sharp then the Luger was originally... Marbles used to make a #27 gold bead sheared blade, but they were pretty low as I remember?... That's the limit of what I know so far! And the search continues... Best to all, til...lat'r....GT....

03-10-2017, 10:54 PM	#11
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,528 Thanks: 1,334 Thanked 3,711 Times in 1,014 Posts	Mauser custom blade! Hi Don, yes! That is the Mauser custom blade from Brownells.... It works out well for you as you have the adj. rear sight mounted on the rear toggle... You would need to lower it some, and profile and shape correctly for a Luger rear sight... But, the main problem with that particular sight is the cost $25.00 each!!! ... That is more then I usually make on most of my barrel projects... .... (see profitability / feasibility study! ) also, once cut for the Mauser blade.. there is no going back... Neat shooter Don, you need to print that baby on paper and see what you can hold for a group... Inqusitive minds want to know! best to all, til...lat'r...GT....

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-09-2017, 11:39 AM	#1
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,967 Thanks: 2,066 Thanked 4,596 Times in 2,117 Posts	Luger sights? Okay, I have picked up a number of front sights over the last few years, and curious to what others think they are? #1 container said P38 #2 container said 1914 #3 look new made the rest others look like possible marbles type - someone said carbine or carbine type (rifle?) Attached Thumbnails

03-09-2017, 01:00 PM	#2
DavidJayUden Patron LugerForum Patron Join Date: Nov 2008 Posts: 4,047 Thanks: 578 Thanked 1,414 Times in 887 Posts	Group 1, second from the right side, appears like something for a K98 rifle. I need a tall front sight blade for my Navy shooter, and learned that the groove size is common to Euro. guns. I still need a tall front sight blade if any of them are available. dju

03-09-2017, 01:24 PM	#3
DonVoigt User Join Date: Apr 2015 Location: near Charlotte NC Posts: 4,681 Thanks: 1,443 Thanked 4,355 Times in 2,041 Posts	Ed, I think they are what you say. VI is probably for the K98 or similar. DJU, K98 sights are available online from the big guys and cheaper than luger sights, and they do fit the dovetail, just need the "wings" cliped to fit! Well, sometimes you need to do a little needle file work on any dovetail sight to get it to fit well. __________________ 03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie

03-09-2017, 03:02 PM	#5
DavidJayUden Patron LugerForum Patron Join Date: Nov 2008 Posts: 4,047 Thanks: 578 Thanked 1,414 Times in 887 Posts	Ed: The one you circled is similar to one I bought from Sarco and was called a "K98 tall sight". Sometime send me a photo of your tallest sights and hopefully we can find one taller than what I have because even with that K98 tall sight, my Navy still prints high. And I'll measure what I have. dju

03-09-2017, 04:18 PM	#6
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,967 Thanks: 2,066 Thanked 4,596 Times in 2,117 Posts	David, will do - will put them alongside each other and see which is tallest. email sent

03-10-2017, 04:38 PM	#7
Diver6106 User Join Date: Sep 2014 Location: Mt. Vernon VA Posts: 245 Thanks: 1,433 Thanked 117 Times in 75 Posts	I put a type IV on a 22LR Luger I have that was missing the front sight. It fit fine.

03-10-2017, 08:04 PM	#10
DonVoigt User Join Date: Apr 2015 Location: near Charlotte NC Posts: 4,681 Thanks: 1,443 Thanked 4,355 Times in 2,041 Posts	This sight is tall, and works fine as set up. GT sent it to me, he can confirm- but I think it came from Brownell's. Attached Thumbnails __________________ 03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie

03-11-2017, 12:05 AM	#13
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,967 Thanks: 2,066 Thanked 4,596 Times in 2,117 Posts	That's the five inch right? My six inch is just too heavy, so it's finicky . Maybe take a Dremel to the sides

03-12-2017, 12:18 AM	#15
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,967 Thanks: 2,066 Thanked 4,596 Times in 2,117 Posts	I might, we'll chat Ed

03-16-2017, 07:44 PM	#16
Diver6106 User Join Date: Sep 2014 Location: Mt. Vernon VA Posts: 245 Thanks: 1,433 Thanked 117 Times in 75 Posts	Lifer- I have a 1913 DWM converted to 22LR, #1057. The barrel is sleeved and the breechblock cut back to the shorter length, with a 22LR seating cut. Then the firing pin was cut flat with a pin drilled and side mounted to it with a whole side cut. But it still needs to have the bottom of the breechblock machined, as in a 22 conversion kit, so it will feed rounds off a conversion kit 22LR mag. As it is it is single shot.