Quick Question About a S/42

wlyon · 10-24-2012, 04:26 PM

Your magizine sounds like a Swiss Mag. According to my references the main toggle pin should have the last two digits of the serial number on it. Since this has been reblued it shouldn't make any difference. Enjoy your luger. Should make a great shooter. Bill

regul · 10-24-2012, 05:40 PM

Reinhardt
It sounds like you have a Swiss 06/29 magazine. The cross should be in the center of the right finger grip. The script P at the base of the spine identifies the maker as Rudolf Pfanninger of Stafa (ZH).

Logante · 10-24-2012, 09:50 PM

Ok so one piece is not numbered to the gun, I can live with that. The only problem is that the reblue has made the gun tighter than it should be. The gun stove pipes with every type of 9mm I have shot through it. WWB, Federal, S&B etc. My only option is going to be thinning the blue where the metal contacts reduce friction. Remove a layer of blueing not any metal.
The cross is in the right side dish. Just like described. The funny thing is that this pistol had reproduction Swiss Bern style grips on it. Older (1960's) reproduction and Italian made.

Its a shooter so I made it look how I like it. I had to go with a classic rosewood for the grips and use only Mec-Gar mags as I am afraid of damaging the older mags I do have.

My other is an original DWM Artillery model thats a little beat up, but shoots great and looks ok.

Thank you both for your input on this. I knew it was a shooter, but I just was trying to find out if it should have the numbered pin. The grips mag and finish were altered, I wanted it to shoot and because it looks sharp.

10-24-2012, 04:26 PM	#1
wlyon Lifer 2X Lifetime Forum Patron Join Date: May 2005 Location: Somewhere in Montana Posts: 2,676 Thanks: 3,247 Thanked 2,669 Times in 991 Posts	Your magizine sounds like a Swiss Mag. According to my references the main toggle pin should have the last two digits of the serial number on it. Since this has been reblued it shouldn't make any difference. Enjoy your luger. Should make a great shooter. Bill __________________ Bill Lyon

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

10-24-2012, 05:40 PM	#2
regul Patron LugerForum Patron Join Date: Sep 2002 Location: VA Posts: 96 Thanks: 19 Thanked 57 Times in 20 Posts	Reinhardt It sounds like you have a Swiss 06/29 magazine. The cross should be in the center of the right finger grip. The script P at the base of the spine identifies the maker as Rudolf Pfanninger of Stafa (ZH).

10-24-2012, 09:50 PM	#3
Logante User Join Date: May 2010 Posts: 9 Thanks: 4 Thanked 0 Times in 0 Posts	Ok so one piece is not numbered to the gun, I can live with that. The only problem is that the reblue has made the gun tighter than it should be. The gun stove pipes with every type of 9mm I have shot through it. WWB, Federal, S&B etc. My only option is going to be thinning the blue where the metal contacts reduce friction. Remove a layer of blueing not any metal. The cross is in the right side dish. Just like described. The funny thing is that this pistol had reproduction Swiss Bern style grips on it. Older (1960's) reproduction and Italian made. Its a shooter so I made it look how I like it. I had to go with a classic rosewood for the grips and use only Mec-Gar mags as I am afraid of damaging the older mags I do have. My other is an original DWM Artillery model thats a little beat up, but shoots great and looks ok. Thank you both for your input on this. I knew it was a shooter, but I just was trying to find out if it should have the numbered pin. The grips mag and finish were altered, I wanted it to shoot and because it looks sharp.