LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > Luger Discussion Forums > All P-08 Military Lugers

Reply
Thread Tools Display Modes
Unread 09-30-2024, 06:46 PM   #1
heysox
New User
 
Join Date: Sep 2024
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Default Feeding Issue

I took a friend shooting so she could try out her late Granddad's bring home Luger. It's an early (1913) Erfurt. The magazine seems period correct but has a different serial number, which is not unusual for military firearms. (I'm certainly no expert). I'm a Luger noobie, but experienced shooter/enthusiast for many decades. The magazine was loaded and has probably been so for decades, as the rounds were tarnished. The Luger (I had previously stripped and cleaned it) fired off the entire mag with no issues. I reloaded it with a mag of Aguila 115 gr. ammo. It would not feed at all. The top round nose dived below the feed ramp. I tried a single round in the mag and that fed just fine into the chamber. I loaded the mag fully and the Luger went through all the rounds with no nose diving or issues. Past experience has taught me that many if not most feeding issues are magazine related. I suggested new magazine springs. She only has the one magazine, so I could not positively say it's a magazine issue, but it seems very likely. Internet research indicates that there are square and non-square mag springs. Any way of knowing that without taking the mag apart? I don't have access to it and wanted to get her the springs as a surprise. Any thoughts from the Luger brain trust? What is the best source for new mag springs? I am sure that there is more than one modern maker. I will check Youtube for videos on swapping out the springs. TIA.
Attached Thumbnails
Click image for larger version

Name:	20240305_130800.jpg
Views:	80
Size:	66.2 KB
ID:	89124  

Click image for larger version

Name:	20240305_130849.jpg
Views:	66
Size:	98.4 KB
ID:	89126  

heysox is offline   Reply With Quote
Unread 09-30-2024, 07:37 PM   #2
Ron Wood
Moderator
2010 LugerForum
Patron
 
Ron Wood's Avatar
 
Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,022
Thanks: 1,090
Thanked 5,178 Times in 1,703 Posts
Default

The magazine is not "period correct", it should have a wood base, not aluminum (which is most likely from the 1920's )
__________________
If it's made after 1918...it's a reproduction
Ron Wood is offline   Reply With Quote
The following 3 members says Thank You to Ron Wood for your post:
Unread 09-30-2024, 08:33 PM   #3
heysox
New User
 
Join Date: Sep 2024
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by Ron Wood View Post
The magazine is not "period correct", it should have a wood base, not aluminum (which is most likely from the 1920's )
Thanks for the clarification. I freely admit my minimal knowledge of Luger minutia. Is there a clue as to the type of mag spring it takes?
heysox is offline   Reply With Quote
Unread 09-30-2024, 10:30 PM   #4
Mac Cat
Lifer
Lifetime Forum
Patron
 
Mac Cat's Avatar
 
Join Date: Apr 2015
Location: Austin, Texas
Posts: 726
Thanks: 2,090
Thanked 606 Times in 327 Posts
Default

Order yourself a Mac-gar brand magazine.
They are readily available in nickel or blue.

That very old magazines spring is probably a little tired.
Leaving magazines full for long periods of time reduces the spring strength, too.
I leave all of them empty for storage.

Make sure you are using FMJ 115gr Target loads like Winchester or PPU.
Mac Cat is offline   Reply With Quote
The following 5 members says Thank You to Mac Cat for your post:
Unread 10-01-2024, 08:41 AM   #5
velodog455~
User
 
Join Date: Aug 2023
Posts: 76
Thanks: 18
Thanked 58 Times in 35 Posts
Default

I'll second getting a Mec-Gar magazine. About $35 shipped as opposed to $100-$200 for a period-correct wood bottom mag that might also have age-related issues.

Here's where to go...
https://gunmagwarehouse.com/mec-gar-...fault_products
velodog455~ is offline   Reply With Quote
Unread 10-01-2024, 11:36 AM   #6
Eugen
User
 
Eugen's Avatar
 
Join Date: Apr 2016
Location: Newburgh,IN
Posts: 790
Thanks: 394
Thanked 631 Times in 334 Posts
Default

OP, you got great advice from the replies above.

I'd also warn you not to try to replace the springs in your original mag. Unless you are very skilled or lucky, you are likely to cosmetically damage or perhaps ruin your original mag in the process. These mags are not your typical vintage mag that are generally friendly for mag spring replacement. There's a member on the forum named "G.T." that can replace the spring for you. He has fixed many for folks and he did a fine job on a mag for me.

So, just get a Mec-Gar mag and store your non-period correct, original mag. Lastly, I trust you properly cleaned and lubed your Erfurt before taking it to the range.
__________________
“God created war so that Americans would learn geography.”
― Mark Twain
Eugen is offline   Reply With Quote
The following 2 members says Thank You to Eugen for your post:
Unread 10-01-2024, 11:51 AM   #7
heysox
New User
 
Join Date: Sep 2024
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Thanks to all who responded. The Luger was carefully cleaned and lubed before use. I will pass along the Mec Gar info to my friend.
heysox is offline   Reply With Quote
Unread 10-17-2024, 06:49 AM   #8
Dwight Gruber
User
 
Join Date: Jun 2002
Location: Portland, Oregon
Posts: 3,902
Thanks: 0
Thanked 1,316 Times in 430 Posts
Default

A potential problem here is the choice of ammunition. Not all brands work well, there is an issue with modern-spec 9x19mm overall length. Winchester white-box and Magtek are both brands I know work well.

--Dwight
Dwight Gruber is online now   Reply With Quote
Unread 10-17-2024, 11:24 AM   #9
velodog455~
User
 
Join Date: Aug 2023
Posts: 76
Thanks: 18
Thanked 58 Times in 35 Posts
Default

This is also true of reloading empty cases from certain brands. Even though they pass the double test of using a cartridge headspace gage, as well as manually dropping them into a clean P.08 chamber, some case brands just don't want to feed. In particular I have had problems with PMC and Aguila cases.

Reloading problems are exacerbated if using even once-fired brass from a Glock due to its oversize chamber. Also, using .356" bullets gives more problems than using .355" bullets because some cases are just too thick to allow .356" bullets to seat without bulging then neck to the point that the reload will not fully enter the chamber.

You would think that .001" would not make that much difference but sometimes it does. The good news is that if the reloads won't go into a Luger chamber you can always fire them in a Glock with impunity (I might have crossed a line of some sort here).
velodog455~ is offline   Reply With Quote
Unread 10-17-2024, 04:34 PM   #10
rhuff
Patron
LugerForum
Patron
 
rhuff's Avatar
 
Join Date: Mar 2011
Location: Az.
Posts: 2,291
Thanks: 2,709
Thanked 972 Times in 717 Posts
Default

It seems to me that each Luger when not using the original 9mm ammo is it's own "animal". I say that as Velodog455 can't use PMC ammo or fired cases to reload, and all of my 9mm Lugers love PMC ammo and I usually keep 1-2 cases of it in stock. I also have reloaded thousands of PMC brass with no problems in MY Lugers.

One just needs to try different ammo and see what YOUR Luger likes and will function correctly with.
__________________
Need DWM breechblock #21
rhuff is offline   Reply With Quote
Unread 10-29-2024, 04:50 PM   #11
rigby560u
New User
 
Join Date: Oct 2024
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Default Das eagle und Goose

Hope you can stand another new guy. I have a P.O8 with byf and (I think) serial # 7124. It is covered with the number 34 which seems to be for keeping all the parts for this gun together. There is a number 41 over the breech.
My questions are about 2 markings:
One is a tiny Germen eagle and swastika on the barrel - near the chamber end. The barrel is shart.
The second is from the magazine which has the number 4249 on its butt. It looks like a tiny goose and it is just below the number.

https://forum.lugerforum.com/images/attach/jpg.gif
20241028_195716.jpg
rigby560u is offline   Reply With Quote
Unread 10-29-2024, 05:17 PM   #12
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,696
Thanks: 792
Thanked 1,679 Times in 552 Posts
Default

Quote:
Originally Posted by rigby560u View Post
Hope you can stand another new guy. I have a P.O8 with byf and (I think) serial # 7124. It is covered with the number 34 which seems to be for keeping all the parts for this gun together. There is a number 41 over the breech.
My questions are about 2 markings:
One is a tiny Germen eagle and swastika on the barrel - near the chamber end. The barrel is shart.
The second is from the magazine which has the number 4249 on its butt. It looks like a tiny goose and it is just below the number.

https://forum.lugerforum.com/images/attach/jpg.gif
20241028_195716.jpg
Welcome to the forum. Lots of knowledgeable people here.

You will have a much better chance of getting answers to your questions if you start a new thread rather than adding on to a much older one.
Doubs is offline   Reply With Quote
The following 2 members says Thank You to Doubs for your post:
Unread 10-30-2024, 04:01 PM   #13
rigby560u
New User
 
Join Date: Oct 2024
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by Doubs View Post
Welcome to the forum. Lots of knowledgeable people here.

You will have a much better chance of getting answers to your questions if you start a new thread rather than adding on to a much older one.
How do I do that? I find navigation here challenging, as in trouble sending email photos to the post.
Thanks
rigby560u is offline   Reply With Quote
Unread 10-30-2024, 06:16 PM   #14
Mac Cat
Lifer
Lifetime Forum
Patron
 
Mac Cat's Avatar
 
Join Date: Apr 2015
Location: Austin, Texas
Posts: 726
Thanks: 2,090
Thanked 606 Times in 327 Posts
Default

Welcome Rigby560u

You need to explore the forum a little longer and figure out how it works.

Try downloading the FAQs from the menu bar

Then start in the New Collectors.
section.
Mac Cat is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:40 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Lugerforum.com