5,7X19

ESKO · 04-22-2002, 03:01 PM

has anyone made small caliber conversion ?

I have a idea to make 5,7X19 top for luger, using

223 reamer and shortened 223 dies, has any one

tried ?

ps finnish army luger spares are sold, bossible

to gun parts (trought finnish dealer).

auktion was 3 weeks ago.

br Esko

G.T. · 04-22-2002, 07:06 PM

unspellable · 04-23-2002, 08:10 AM

There have been at least three wildcats based on necking the 30 Luger case down to 22. I'm still wishing for more info on them myself. If the cartridge will not deliver enough impulse to cycle properly it is possible to use a recoil spring with one or two turns cut off. I've heard claims of velocities as high as 2000 fps which would deliver enough impulse, but it sounds a trifle optimistic. The Luger action is good to a working pressure of 40,000 CUP (This was the working pressure in the old model carbine) and the current factory loads in 30 Luger run less than 28,000 by way of comparison. The current factory loads don't really deliver enough impulse for reliable cycling with a stock recoil spring.

unspellable

G.T. · 04-23-2002, 09:22 AM

you could use any available .22 bullet, as long as you could seat the combination to an overall satisfactory length..... I don't know if you would have to modify the gun (.30 Luger) at all? Perhaps a weaker mainspring? My biggest concern is whether or not the 4' barrel, and twist, and velocity would be sufficient to make the sabot perform as it should? I would think some of our reloaders could find out pretty quickly if it even works at all! If it did, it would be neat....till....later....G.T.

04-22-2002, 03:01 PM	#1
ESKO User Join Date: Jun 2002 Location: helsinki Posts: 16 Thanks: 0 Thanked 0 Times in 0 Posts	5,7X19 has anyone made small caliber conversion ? I have a idea to make 5,7X19 top for luger, using 223 reamer and shortened 223 dies, has any one tried ? ps finnish army luger spares are sold, bossible to gun parts (trought finnish dealer). auktion was 3 weeks ago. br Esko

04-22-2002, 07:06 PM	#2
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,485 Thanks: 1,283 Thanked 3,581 Times in 989 Posts	what about a sabot, .30 / .22 in a .30 Luger case? (EOM)

04-23-2002, 08:10 AM	#3
unspellable User Join Date: Jun 2002 Location: Iowa Posts: 766 Thanks: 0 Thanked 18 Times in 10 Posts	Re: what about a sabot, .30 / .22 in a .30 Luger c There have been at least three wildcats based on necking the 30 Luger case down to 22. I'm still wishing for more info on them myself. If the cartridge will not deliver enough impulse to cycle properly it is possible to use a recoil spring with one or two turns cut off. I've heard claims of velocities as high as 2000 fps which would deliver enough impulse, but it sounds a trifle optimistic. The Luger action is good to a working pressure of 40,000 CUP (This was the working pressure in the old model carbine) and the current factory loads in 30 Luger run less than 28,000 by way of comparison. The current factory loads don't really deliver enough impulse for reliable cycling with a stock recoil spring. unspellable

04-23-2002, 09:22 AM	#4
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,485 Thanks: 1,283 Thanked 3,581 Times in 989 Posts	With a sabot......... you could use any available .22 bullet, as long as you could seat the combination to an overall satisfactory length..... I don't know if you would have to modify the gun (.30 Luger) at all? Perhaps a weaker mainspring? My biggest concern is whether or not the 4' barrel, and twist, and velocity would be sufficient to make the sabot perform as it should? I would think some of our reloaders could find out pretty quickly if it even works at all! If it did, it would be neat....till....later....G.T.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode