LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > Luger Discussion Forums > Swiss Lugers

Reply
Thread Tools Display Modes
Unread 07-16-2019, 02:57 PM   #1
RShaw
User
 
RShaw's Avatar
 
Join Date: Nov 2016
Location: Venlo, the Netherlands
Posts: 350
Thanks: 160
Thanked 170 Times in 90 Posts
Default Swiss 06/29 Luger- 1940 Bern - best factory ammo?

Hi All,

I have recently acquired a very nice 1940 Bern 06/29 Luger chambered in 7,65 mm which takes the bottleneck casing. Fiocchi continues to make this round, but I am hearing that this ammo is a bit too powerful for the 06/29, while others are of the opinion that it is fine.

I am planning to reload anyway, but I would like the opinions of you experts out there if you don't mind.

I understand that the 06/29 is a very well built firearm but I do not want to risk damage to this gun!

Many thanks!!
__________________
Enjoying any firearm is like staying happily married- take her out on a regular basis, treat her with respect and pay attention to proper maintenance.

Looking for magazine no. 7097
Venlo, the Netherlands- RShaw
RShaw is offline   Reply With Quote
Unread 07-16-2019, 03:29 PM   #2
HerrKaiser
User
 
HerrKaiser's Avatar
 
Join Date: Feb 2018
Location: South Carolina
Posts: 847
Thanks: 782
Thanked 860 Times in 410 Posts
Default

Unless the Swiss springs are notably weaker than their German counterparts, I’ve heard many say the opposite. Prvi Partisan is the more commonly recommended .30 ammo to shoot with as many complain Fiocchi is too weak to reliably cycle the action on their guns. It (Fiocchi) worked fine for my German-made commercial, but I also think it’s spring is weak/old and I only took it to the range once to make sure it works since it is all matching and I have no interest in shooting it any time in the near future.

Do post some pictures of it as well.
__________________
-QM

Looking for Mauser S/42 toggle train #22
HerrKaiser is offline   Reply With Quote
Unread 07-16-2019, 03:55 PM   #3
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,696
Thanks: 792
Thanked 1,679 Times in 552 Posts
Default

If you reload, I STRONGLY suggest using an 86 ~ 90 grain bullet with a cannelure. The short neck of the 30 Luger case may not have sufficient neck tension to prevent the bullet being driven back deeper as it strikes the feed ramp. Thus crimping the case mouth into the cannelure is necessary.

I use .308" 86 grain soft point bullets and 90 grain Hornady .312" XTP HP bullets run through a .310" sizing die. Also, 90 grain Sierra HCSP .312" bullets also run through a .310" sizing die work well but are much more expensive than the XTP bullets.

A good starting load is any of the above bullets over 5.0 grains of Hodgdon CFE Pistol powder. I also chamfer the case mouth to prevent shaving the sides of the bullets.

I have an old take-off 30 caliber Luger barrel that I use to check every round to make sure they chamber properly.
Doubs is offline   Reply With Quote
Unread 07-16-2019, 04:33 PM   #4
RShaw
User
 
RShaw's Avatar
 
Join Date: Nov 2016
Location: Venlo, the Netherlands
Posts: 350
Thanks: 160
Thanked 170 Times in 90 Posts
Default

Wow!! Thanks very much for the details! This is the first time I have heard that the Fiocchi's are too weak. I do have a 1917 DWM P08 in which 9 mm subsonics have shot well. It takes about the same amount of tension to pull both toggles all the way back until the holdopen pops up and engages.

The serial number is the same on the base of the barrel, the frame and the upper of the Swiss 06/29. The firing pin is not numbered- but didn't the Swiss take care to ensure that their parts were more interchangable than did their German counterparts? Therefore a matching Swiss gun does not have as many numbered parts as the German P08?

Obviously there is a lot I do not know- but these guns are fascinating

Thanks for the feedback... Yes I will post some photos as soon as I can take some decent shots tomorrow.
__________________
Enjoying any firearm is like staying happily married- take her out on a regular basis, treat her with respect and pay attention to proper maintenance.

Looking for magazine no. 7097
Venlo, the Netherlands- RShaw
RShaw is offline   Reply With Quote
Unread 07-16-2019, 04:44 PM   #5
rhuff
Patron
LugerForum
Patron
 
rhuff's Avatar
 
Join Date: Mar 2011
Location: Az.
Posts: 2,291
Thanks: 2,709
Thanked 972 Times in 717 Posts
Default

My 30 Luger handguns function fine with the Fiocchi factory IF I use the FMJ, and not the soft point ammo. I have been handloading this brass for many years, and have loaded a fair amount of the 85gr .308in. FMJ bullets, but am not pleased with the end results, as a whole.

I have had my best results with 92gr .311in. lead RN bullets, and 92gr .309in. FMJ bullets. I load them behind a full load of Unique Powder and apply a good crimp with a Lee factory crimp die. This combo works extremely well in all of my 7.65P caliber handguns.....not just my Lugers.


I have no idea what reloading components are available to you, so it is hard to recommend components that I have no history with.
__________________
Need DWM breechblock #21
rhuff is offline   Reply With Quote
The following member says Thank You to rhuff for your post:
Unread 07-17-2019, 07:21 AM   #6
RShaw
User
 
RShaw's Avatar
 
Join Date: Nov 2016
Location: Venlo, the Netherlands
Posts: 350
Thanks: 160
Thanked 170 Times in 90 Posts
Default

Hi All,

Then promised photos below- thanks rhuff for your comments on the FMJ versus soft point...

What difficulties did you have with the soft point?

We have a good LGS here which specializes in reloading- I'm sure I can get details from them. I'll bring all this info to them to be as close to it as possible with the powder, heads and primers available here.

Thanks!
Attached Thumbnails
Click image for larger version

Name:	DSC_9219 OKSm.jpg
Views:	869
Size:	200.6 KB
ID:	77387  

Click image for larger version

Name:	DSC_9220 OKSm.jpg
Views:	857
Size:	200.5 KB
ID:	77388  

Click image for larger version

Name:	DSC_9222 OKSm.jpg
Views:	824
Size:	69.6 KB
ID:	77389  

Click image for larger version

Name:	DSC_9223 OKSm.jpg
Views:	835
Size:	72.1 KB
ID:	77390  

Click image for larger version

Name:	DSC_9226 OKSm.jpg
Views:	816
Size:	151.8 KB
ID:	77391  

Click image for larger version

Name:	DSC_9226 OK_2Sm.jpg
Views:	817
Size:	128.1 KB
ID:	77392  

Click image for larger version

Name:	DSC_9227 OKSm.jpg
Views:	822
Size:	202.9 KB
ID:	77393  

Click image for larger version

Name:	DSC_9231 OKSm.jpg
Views:	846
Size:	51.4 KB
ID:	77394  

Click image for larger version

Name:	DSC_9230 OKSm.jpg
Views:	827
Size:	90.1 KB
ID:	77395  

RShaw is offline   Reply With Quote
The following 2 members says Thank You to RShaw for your post:
Unread 07-17-2019, 02:23 PM   #7
rhuff
Patron
LugerForum
Patron
 
rhuff's Avatar
 
Join Date: Mar 2011
Location: Az.
Posts: 2,291
Thanks: 2,709
Thanked 972 Times in 717 Posts
Default

The Fiocchi soft point 30 Luger ammo has a tendency to stop, or nearly stop, on the feed ramp.....resulting in a missfeed/jam. The FMJ do not do this in MY Lugers. Some folks on this forum report that the soft point Fiocchi ammo functions just fine in their Lugers....
__________________
Need DWM breechblock #21
rhuff is offline   Reply With Quote
The following member says Thank You to rhuff for your post:
Unread 07-17-2019, 03:21 PM   #8
RShaw
User
 
RShaw's Avatar
 
Join Date: Nov 2016
Location: Venlo, the Netherlands
Posts: 350
Thanks: 160
Thanked 170 Times in 90 Posts
Default

Guess there's only one way to find out....
Thanks a lot!
__________________
Enjoying any firearm is like staying happily married- take her out on a regular basis, treat her with respect and pay attention to proper maintenance.

Looking for magazine no. 7097
Venlo, the Netherlands- RShaw
RShaw is offline   Reply With Quote
Unread 07-17-2019, 03:21 PM   #9
Vlim
Moderator
Lifetime
LugerForum Patron
 
Vlim's Avatar
 
Join Date: Oct 2002
Location: Europe
Posts: 5,053
Thanks: 1,036
Thanked 3,988 Times in 1,205 Posts
Default

Shot quite a bit of hard lead Fiocchi through my other 06/29. Never had any issues. Even ran a full Bing 2nd type drum mag through it without a glitch.

My 6 inch Mauser Parabellum didn't like them, though.
Vlim is offline   Reply With Quote
The following 2 members says Thank You to Vlim for your post:
Unread 07-17-2019, 05:49 PM   #10
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,696
Thanks: 792
Thanked 1,679 Times in 552 Posts
Default

Here are my .30 Luger bullets and cartridges. On the far right is my 9mm bullet and cartridge.

L ~ R, .309" 90 grain Hornady HP, .312" 90 grain Sierra Jacketed Hollow Core resized to .310", .312" 85 grain Hornady XTP HP resized to .310", 93 grain custom mold cast bullet, 86 grain .308" soft nose and the last one is a 9mm 115 grain .356" Berry plated flat nose bullet.

Note that after being resized to .310", the Sierra JHC bullet nose is reshaped to pretty much a round nose but still has a hollow point. It was designed for the .32 H&R Magnum cartridge.

I ordered a custom mold to cast the 93 grain cast bullets. My design had a much larger meplat but the maker made it as you see it. I size them to .310" and they work great but I'd still like a bigger meplat.

All of the 30's are loaded with 5.0 grains of Hodgdon CFE Pistol powder and they all function just fine in my Lugers. However, in my Benelli B80 and Browning HP, they do not.

The 115 grain 9mm load is 5.6/5.7 grains of CFE Pistol powder and they work beautifully in my shooter Lugers.

Doubs is offline   Reply With Quote
The following 2 members says Thank You to Doubs for your post:
Unread 07-18-2019, 02:15 AM   #11
Sieger
User
 
Sieger's Avatar
 
Join Date: Jul 2003
Location: New York, NY
Posts: 1,575
Thanks: 2,124
Thanked 400 Times in 249 Posts
Default

Quote:
Originally Posted by Doubs View Post
Here are my .30 Luger bullets and cartridges. On the far right is my 9mm bullet and cartridge.

L ~ R, .309" 90 grain Hornady HP, .312" 90 grain Sierra Jacketed Hollow Core resized to .310", .312" 85 grain Hornady XTP HP resized to .310", 93 grain custom mold cast bullet, 86 grain .308" soft nose and the last one is a 9mm 115 grain .356" Berry plated flat nose bullet.

Note that after being resized to .310", the Sierra JHC bullet nose is reshaped to pretty much a round nose but still has a hollow point. It was designed for the .32 H&R Magnum cartridge.

I ordered a custom mold to cast the 93 grain cast bullets. My design had a much larger meplat but the maker made it as you see it. I size them to .310" and they work great but I'd still like a bigger meplat.

All of the 30's are loaded with 5.0 grains of Hodgdon CFE Pistol powder and they all function just fine in my Lugers. However, in my Benelli B80 and Browning HP, they do not.

The 115 grain 9mm load is 5.6/5.7 grains of CFE Pistol powder and they work beautifully in my shooter Lugers.

Doubs,

Would you share with us please information on your custom mold maker?

Thanks!


Sieger
Sieger is offline   Reply With Quote
The following member says Thank You to Sieger for your post:
Unread 07-18-2019, 12:27 PM   #12
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,696
Thanks: 792
Thanked 1,679 Times in 552 Posts
Default

Quote:
Originally Posted by Sieger View Post
Doubs, Would you share with us please information on your custom mold maker? Thanks!

Sieger
My 4 gang mold came from LBT: http://lbtmolds.com/

My mold is number 313 95 TC

I've had my mold for some years so I have no idea what the cost would be today. I can say that the quality is first class and the mold drops a beautiful bullet.
Doubs is offline   Reply With Quote
Unread 07-19-2019, 05:55 PM   #13
RShaw
User
 
RShaw's Avatar
 
Join Date: Nov 2016
Location: Venlo, the Netherlands
Posts: 350
Thanks: 160
Thanked 170 Times in 90 Posts
Default

Well, I have the Fiocchi .30 cal FMJ on order which I can pick up Tuesday.
That gets me some more brass as well as experiece shooting this gun. Many thanks for all the reloading detals above!!

Last time I reloaded was 38 years ago- 45LC when living in the US, was great fun, but the details are lost to me and the technology and precision equipment available today is a big change from back then.....
RShaw is offline   Reply With Quote
The following 2 members says Thank You to RShaw for your post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:11 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Lugerforum.com