LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Repairs, Restoration & Refinishing

Reply
Thread Tools Display Modes
Unread 09-01-2024, 06:05 PM   #1
stretchman25
New User
 
Join Date: Aug 2024
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Default locking bolt/take down lever hard to operate

Several months ago I purchased my first P-08. It is a “mix master special” or in more appropriate terms is a gun that was pieced together from various parts. When I disassemble it, I have to use a hard wood dowel to move the locking bolt/ disassembly lever to the downward position. Watching videos of field stripping a P-08 show that just finger pressure is enough to move the locking bolt downward and thus allow removal of the side plate. Are there any adjustments that can be made in order to make moving the locking bolt downward easier?
stretchman25 is offline   Reply With Quote
Unread 09-01-2024, 07:31 PM   #2
Mac Cat
Lifer
Lifetime Forum
Patron
 
Mac Cat's Avatar
 
Join Date: Apr 2015
Location: Austin, Texas
Posts: 711
Thanks: 2,073
Thanked 591 Times in 317 Posts
Default

That is a pretty common feature of many semi-auto pistols, not just the Luger.
Sometimes you can just work them to loosen up, using oil.

You may also want to remove the small tension spring and see if the lever is still stiff.
If it is, it may need some filing to fit properly.
Or, you can buy another one pretty easily and see if a different one fits better.
They are not completely interchangeable parts - some need hand fitting.

The springs are fairly easy to remove and replace.
Some lugers don't even have one, but that wouldn't be smart for a pistol you are going to shoot.

Glad you chose to use a wooden stick and not a pair of piers !
Mac Cat is offline   Reply With Quote
The following member says Thank You to Mac Cat for your post:
Unread 09-01-2024, 09:53 PM   #3
Ron Wood
Moderator
2010 LugerForum
Patron
 
Ron Wood's Avatar
 
Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,010
Thanks: 1,088
Thanked 5,149 Times in 1,694 Posts
Default

This may be a dumb question, and I apologize if it is, but are you retracting the receiver a bit to take the pressure off of the locking bolt?
Ron
__________________
If it's made after 1918...it's a reproduction
Ron Wood is offline   Reply With Quote
The following 3 members says Thank You to Ron Wood for your post:
Unread 09-02-2024, 08:26 AM   #4
velodog455~
User
 
Join Date: Aug 2023
Posts: 73
Thanks: 18
Thanked 56 Times in 34 Posts
Default

You can easily check Ron's question by simply locking the toggle back, which takes the pressure off the locking block, and seeing if the rotating effort changes.

I've encountered this problem before. Here's how I fixed mine. Might or might work for you as well, I dunno.

With the pistol fully assembled, look carefully to see if the sideplate extension under the locking bolt is fully seated down on the frame. If so, and the sideplate and the locking bolt have different numbers then it is possible that the portion of the sideplate that the locking bolt rides over is a hair too thick. Or, it could be the locking bolt handle that is too thick.

Either way, you can carefully file a couple of thousandths off either that top part of the sideplate or from the underside of the locking bolt. Touch up with cold blue. It's often difficult to fit parts properly without sacrificing a bit of finish.

Also, with the sideplate, barrel, & barrel extension removed does the locking bolt then rotate easily in the frame? That is probably a good clue that you have an easily fixable tolerance stacking issue as noted above caused by mis-matched parts.

It COULD be the locking bolt spring is out of spec but I suspect otherwise, especially if the locking bolt rotates easily with the top half of the pistol off the frame.
-Bob
velodog455~ is offline   Reply With Quote
The following member says Thank You to velodog455~ for your post:
Unread 09-02-2024, 08:46 AM   #5
Eugen
User
 
Eugen's Avatar
 
Join Date: Apr 2016
Location: Newburgh,IN
Posts: 787
Thanks: 390
Thanked 627 Times in 332 Posts
Default

OP, my shooter, a franken luger, had a similar problem when I acquired it about 8 years ago. I worked on it and eventually got it to behave better. I wish I could recall what I did exactly, but I did do some light filing/polishing particularly on the side plate. I think.

One of the gifts of owning a mixed parts Luger is that you get the joy of learning how to fit missmatching parts and then you get to brag about your gunsmithing skills. I am a level three Bubba

Keep us posted on your journey.
__________________
“God created war so that Americans would learn geography.”
― Mark Twain
Eugen is offline   Reply With Quote
The following 3 members says Thank You to Eugen for your post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:37 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Lugerforum.com