my profile |
register |
faq |
search upload photo | donate | calendar |
07-14-2013, 07:10 PM | #1 |
New User
Join Date: May 2013
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
Front Sight Blade Removal
Hi,
Does anyone know how to remove the front sight blade on a Luger? Regards, |
07-14-2013, 07:19 PM | #2 |
Patron
LugerForum Patron Join Date: Mar 2011
Location: Az.
Posts: 2,288
Thanks: 2,702
Thanked 971 Times in 716 Posts
|
I use a WELL padded vise to hold the bbl. and then use a small brass drift and hammer. I remove mine right to left. Others may have a different technique.
|
The following 3 members says Thank You to rhuff for your post: |
07-16-2013, 11:29 PM | #3 |
Twice a Lifer
Lifetime Forum Patron Join Date: Mar 2011
Location: Atop the highest hill in Schuyler County NY
Posts: 3,327
Thanks: 7,215
Thanked 2,542 Times in 1,351 Posts
|
I once heard, "It's the things that seem not to need saying that need saying the most."
In that vein, I wouldn't drift the blade, rather the end(s) of the portion of the sight that is submerged in the dovetail in the sight block.
__________________
"... Liberty is the seed and soil, the air and light, the dew and rain of progress, love and joy."-- Robert Greene Ingersoll 1894 |
07-17-2013, 12:22 PM | #4 |
Moderator
Lifetime Forum Patron Join Date: Jun 2002
Location: Arizona/Colorado
Posts: 7,766
Thanks: 4,886
Thanked 3,121 Times in 1,432 Posts
|
Yes, Only push on the bottom for sure. I have a sight adjusting tool I use..it fits on the muzzle and a screw pushes over the sight. These tools are not common. But for a one time deal Rhuff has good advise. Just drift it out. On most pins on a Luger I go right to left to extract.
__________________
Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 lugerholsterrepair@earthlink.net 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know." |
07-19-2013, 12:25 AM | #5 |
User
Join Date: May 2013
Posts: 33
Thanks: 12
Thanked 8 Times in 6 Posts
|
if you're worried about damaging the blade , try using an aluminum drift punch when drifting it out . and be sure to only applying the pressure on the blades base (inside the barrels dovetail) , as it could get bent otherwise . a simple way to pad it "MIGHT" be to use a short piece of copper tubing ( be sure to de-burr it as well ) that is slit length wise to allow for contraction (when being held by the vise) and ALSO lined with leather to protect the barrel's finish .
It is also a good idea to have a proper size round pin the is a close fit to slide inside the barrel , to keep from accidentally "crushing" the barrel ; it should be able to side in only by finger pressure . A suitable size pin can be turned down from mild steel ( and polished ) by any machinist , or easily home made by using a power drill to turn it and carefully filling it to the proper diameter ( check with micrometer or calipers for uniformity ) ; polishing to get the final fit . --- this is a common practice when changing any pistol / revolver barrel as they are often very thin walled and it really doesn't take as much pressure as one would think to distort the inside bore size a little . --- an once of prevention is worth a pound of cure .... |
Tags |
front sight, luger, removal |
Thread Tools | |
Display Modes | |
|
|