loading tool help

Rick W. · 11-10-2004, 07:41 PM

i

G.W. Gill · 11-11-2004, 01:41 AM

My "135" is a hair over 24mm wide at the wings. Length, from the center, where you put your thumb, to the tip 50mm. Hole 10mm. Groove 4mm. Guide 8mm. Lip inside the hole 1mm. Width above the wing 12mm. At the screwdriver end 7mm. This is by my super cheap plastic instrument!!! Beware.

Fritzer · 11-11-2004, 01:13 PM

Rick,

Could I ask for pictures of the project?

I have been considering a similar woodworking activity and have been collecting as many examples on the net, to incorporate into my own configuration.

Sounds like a very special gift - how did you know what I wanted ?

Best Regards,
Fritz.

G.W. Gill · 11-12-2004, 01:07 AM

Rick and Fritz, My calipers are plastic and cheap. Happy hour is also about ten at night and I hit the comp at midnight. I did try to find the specs in my references but was unable. I have seen the pics and it is driving me crazy. They are pretty standard and I am not that far off. It is / was after eleven and I am Scott Irish...

G.W. Gill · 11-13-2004, 03:01 AM

I have to pay more attention. I just welcomed Rick to the Forum in a PM. It is not justifiable, I have been reading his posts for years. I apologize. HI Rick!, I have been a litle distracted lately.

Edward Tinker · 11-13-2004, 09:05 AM

Gill, nothing worse than making a guy feel welcomed

Yes, I've done the same thing..... been distracted, not made a mistake <img border="0" alt="[hiha]" title="" src="graemlins/roflmao.gif" />

G.W. Gill · 11-14-2004, 01:08 AM

Thanks Ed, Essentially what I said was a couple dozen guys with micrometers would have jumped in to help if I had been way off. And this is a good place...

11-10-2004, 07:41 PM	#1
Rick W. User Join Date: Jun 2002 Posts: 339 Thanks: 81 Thanked 359 Times in 198 Posts	loading tool help i

11-13-2004, 09:05 AM	#6
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,912 Thanks: 1,989 Thanked 4,502 Times in 2,077 Posts	Gill, nothing worse than making a guy feel welcomed Yes, I've done the same thing..... been distracted, not made a mistake <img border="0" alt="[hiha]" title="" src="graemlins/roflmao.gif" /> __________________ Edward Tinker ************ Co-Author of Police Lugers - Co-Author of Simson Lugers Author of Veteran Bring Backs Vol I, Vol II, Vol III and Vol IV

11-11-2004, 01:41 AM	#2
G.W. Gill User Join Date: Jun 2002 Location: Southeastern USA Posts: 369 Thanks: 0 Thanked 0 Times in 0 Posts	My "135" is a hair over 24mm wide at the wings. Length, from the center, where you put your thumb, to the tip 50mm. Hole 10mm. Groove 4mm. Guide 8mm. Lip inside the hole 1mm. Width above the wing 12mm. At the screwdriver end 7mm. This is by my super cheap plastic instrument!!! Beware.

11-11-2004, 01:13 PM	#3
Fritzer User Join Date: Nov 2002 Location: Michigan Posts: 134 Thanks: 0 Thanked 0 Times in 0 Posts	Rick, Could I ask for pictures of the project? I have been considering a similar woodworking activity and have been collecting as many examples on the net, to incorporate into my own configuration. Sounds like a very special gift - how did you know what I wanted ? Best Regards, Fritz.

11-12-2004, 01:07 AM	#4
G.W. Gill User Join Date: Jun 2002 Location: Southeastern USA Posts: 369 Thanks: 0 Thanked 0 Times in 0 Posts	Rick and Fritz, My calipers are plastic and cheap. Happy hour is also about ten at night and I hit the comp at midnight. I did try to find the specs in my references but was unable. I have seen the pics and it is driving me crazy. They are pretty standard and I am not that far off. It is / was after eleven and I am Scott Irish...

11-13-2004, 03:01 AM	#5
G.W. Gill User Join Date: Jun 2002 Location: Southeastern USA Posts: 369 Thanks: 0 Thanked 0 Times in 0 Posts	I have to pay more attention. I just welcomed Rick to the Forum in a PM. It is not justifiable, I have been reading his posts for years. I apologize. HI Rick!, I have been a litle distracted lately.

11-14-2004, 01:08 AM	#7
G.W. Gill User Join Date: Jun 2002 Location: Southeastern USA Posts: 369 Thanks: 0 Thanked 0 Times in 0 Posts	Thanks Ed, Essentially what I said was a couple dozen guys with micrometers would have jumped in to help if I had been way off. And this is a good place...