LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Repairs, Restoration & Refinishing

Reply
Thread Tools Display Modes
Unread 03-24-2021, 01:22 PM   #1
Edward Tinker
Super Moderator
Eternal Lifer
LugerForum
Patron
 
Edward Tinker's Avatar
 
Join Date: Jun 2002
Location: North of Spokane, WA
Posts: 15,902
Thanks: 1,981
Thanked 4,487 Times in 2,071 Posts
Default Howard Collins (PoliceLuger) - STRAWING

MY good friend Howard (known as Policeluger here) made a How To years ago, I think you can find it, but his wife Sandi sent me this from Howards laptop files. Howard died 11/28/2018.


COLLINS GUNSMITHING
HOWARD COLLINS
User name PoliceLuger
STRAWING

This is a fast and very simple process. Do not make it complicated. If it is not going smooth, stop, take a break and start again. You cannot mess it up. You may have to start over, especially if you have achieved a color darker than you wish. It just a matter of re-polishing and heat treating again, of course buffing can take a toll on proof marks and serial numbers so you want to be cautious. I learned this process from harry jones in his Torrance California shop approx. 35 years ago and have done perhaps 400 or so lugers since then.
On the checkered areas, mag release, take down lever, it may be good enough just too heavy wire brush the checkered areas, I use a wire wheel on my buffing machine. However, I have used a small wire wheel on a Dremel tool and achieved the same degree of cleaning. I polish the small parts with 240 grit polish on the buffing wheel. You do not want to take the surface to a bright chrome finish, as that would not be in pace with factory work, and you want to come close to what was done at that period. Tight hard to get in places can be polished with approx. 360 grit sand paper. You do not need to polish the surfaces that do not show when the gun is assembled, even if the part is already blue or patinaed. It makes for a more professional job if you do, but in areas behind the trigger, this may get tough to get too, also if your ejector has a bit of pitting, you want to polish it out on the area that shows when assembled, but if removing pits on under side is going to make it to thin, stop after outside is done…. Un-seen/un-polished parts will not affect the outcome of the polished areas.
Once polished, I use something like gun scrub too degrease the entire part…the entire part…also degrease the tools you are going to use. I use heavy tweezers too handled the parts once cleaned, and as they come out of the oven. Degrease the part of the tool that will come into contact with the part. Even clean washed hands will leave some oils on the parts so be careful. Oil will mess/gung up the finish.
Heat oven to approx. 450* (degrees f), the hotter the oven the darked the color. But a hot oven will also color faster, so watch out. Go to 530* for a darked Krieghoff look 530*, 510* for 1940-43 ejector temper blue…. But just stick with 450* and you most likely will be just fine. Place parts in a small de-greased pie tin in center of oven and stand back…before your eyes it will start turning that magical straw color. Now smaller thinner parks will color faster, take them out as you achieve the color you want…if it is past what you want in color, cool/re-polish and degrease and start over. Heavy thicker parts will take longer. Important here, and this is where Mr. Jones and I differ. Once you got the color, right out of the oven start cooling with oil, any light oil. I use 3in1, but any sewing machine/lite gun oil will work…. Several light drops, don’t be cheap on the oil, but no need to have the part swimming in it. Cool down too room temp, wipe access oil and install. Wow!!!! It is that easy, I have instructed people all over the world. On how to do it, have fun and pride in doing it, and save a buck...

--------------
I have included it as a PDF if anyone wants to save it, please give him credit if you do.
Attached Files
File Type: pdf STRAW.pdf (56.8 KB, 128 views)
Edward Tinker is offline   Reply With Quote
The following 8 members says Thank You to Edward Tinker for your post:
Unread 03-24-2021, 01:57 PM   #2
cirelaw
Lifer
Lifetime Forum
Patron
 
Join Date: Dec 2003
Location: PORT ST LUCIE, FLORIDA
Posts: 12,216
Thanks: 6,209
Thanked 4,133 Times in 2,173 Posts
Default

Ed, Thanks, I wondered how its done! Debby would kick me out of the house for using her oven!
Attached Images
  
cirelaw is offline   Reply With Quote
The following 2 members says Thank You to cirelaw for your post:
Unread 03-24-2021, 03:52 PM   #3
rhuff
Patron
LugerForum
Patron
 
rhuff's Avatar
 
Join Date: Mar 2011
Location: Az.
Posts: 2,269
Thanks: 2,678
Thanked 956 Times in 702 Posts
Default

Thanks Ed for Howard's write up. I have strawed a couple of parts in the past, and if memory serves, I used a little lower temp, but not by much.
__________________
Need DWM breechblock #21
rhuff is offline   Reply With Quote
The following member says Thank You to rhuff for your post:
Unread 03-24-2021, 04:14 PM   #4
cirelaw
Lifer
Lifetime Forum
Patron
 
Join Date: Dec 2003
Location: PORT ST LUCIE, FLORIDA
Posts: 12,216
Thanks: 6,209
Thanked 4,133 Times in 2,173 Posts
Default

Were there standards as to blueing with each maker? None of mine look almost as good above! Does age alone affect the intensity?
cirelaw is offline   Reply With Quote
Unread 03-24-2021, 07:39 PM   #5
spangy
Lifer
Lifetime Forum
Patron
 
spangy's Avatar
 
Join Date: Sep 2020
Location: Winnipeg, Canada
Posts: 606
Thanks: 2,964
Thanked 1,047 Times in 422 Posts
Default

Thanks a million Ed
Perfect timing ... I was about to give straw bluing a go myself.

Rest in Peace Howard ... and Thank you
__________________
Whoever said that "money can't buy you happiness" never bought a Luger.
WTB - Take Down Lever & Trigger Plate (#90) for an Imperial Artillery.
spangy is offline   Reply With Quote
The following 2 members says Thank You to spangy for your post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:56 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Lugerforum.com