DWM 1908 Commercial - Page 3

Classic Captain · 01-23-2013, 04:46 PM

B close up

Dwight Gruber · 01-23-2013, 05:01 PM

If you can find a friend with a closeup lens on a camera it would be very helpful. We need to see fine enough detail to determine if the c/N is stamped, engraved, or pantographed.

--Dwight

Classic Captain · 01-23-2013, 07:49 PM

See if any better

Classic Captain · 01-23-2013, 07:54 PM

So apparently it does have hold open latch , spring it flattened.

Dwight Gruber · 01-23-2013, 08:13 PM

Very much better, thank you. Good enough to see that the c/N and barrel serial numbers are clearly pantographed. Authentic proof marks and serial numbers are stamped, without exception.

Also glad to see the witness mark, notice that the barrel flange is slightly smaller than the receiver, and the witness mark itself is a hash of strikes, neither characteristic of DWM "fit andf finish."

--Dwight

Classic Captain · 01-23-2013, 08:37 PM

So what do we have here?
A re barreled p08 short frame , value?

Classic Captain · 01-27-2013, 09:27 PM

Thank you all, for your expertise . I have withdrawn from purchasing this Luger.

Ben M. · 01-28-2013, 12:51 PM

is seems like the barrel shoulder flange is very thick. is this normal or an indication of a replacement barrel?

alanint · 01-28-2013, 01:13 PM

Ben,

This is an aftermarket, not quite finished barrel that someone placed on the gun and force matched with spurious barrel markings.

You are correct in that the flange is too thick.

Classic Captain · 01-28-2013, 11:41 PM

Had I known you were in Miami , Alanint . I would have had you inspect it.
I am in Miami Beach.

alanint · 01-29-2013, 05:27 AM

I would have been glad to take a look, although I am no expert.

01-23-2013, 04:46 PM	#41
Classic Captain User Join Date: Dec 2012 Posts: 56 Thanks: 1 Thanked 0 Times in 0 Posts	Best I can get B close up Attached Thumbnails

01-23-2013, 07:49 PM	#43
Classic Captain User Join Date: Dec 2012 Posts: 56 Thanks: 1 Thanked 0 Times in 0 Posts	Try this See if any better Attached Thumbnails

01-23-2013, 05:01 PM	#42
Dwight Gruber User Join Date: Jun 2002 Location: Portland, Oregon Posts: 3,889 Thanks: 0 Thanked 1,281 Times in 423 Posts	If you can find a friend with a closeup lens on a camera it would be very helpful. We need to see fine enough detail to determine if the c/N is stamped, engraved, or pantographed. --Dwight

01-23-2013, 07:54 PM	#44
Classic Captain User Join Date: Dec 2012 Posts: 56 Thanks: 1 Thanked 0 Times in 0 Posts	So apparently it does have hold open latch , spring it flattened.

01-23-2013, 08:13 PM	#45
Dwight Gruber User Join Date: Jun 2002 Location: Portland, Oregon Posts: 3,889 Thanks: 0 Thanked 1,281 Times in 423 Posts	Very much better, thank you. Good enough to see that the c/N and barrel serial numbers are clearly pantographed. Authentic proof marks and serial numbers are stamped, without exception. Also glad to see the witness mark, notice that the barrel flange is slightly smaller than the receiver, and the witness mark itself is a hash of strikes, neither characteristic of DWM "fit andf finish." --Dwight

01-23-2013, 08:37 PM	#46
Classic Captain User Join Date: Dec 2012 Posts: 56 Thanks: 1 Thanked 0 Times in 0 Posts	So what do we have here? A re barreled p08 short frame , value?

01-27-2013, 09:27 PM	#47
Classic Captain User Join Date: Dec 2012 Posts: 56 Thanks: 1 Thanked 0 Times in 0 Posts	Thank you all, for your expertise . I have withdrawn from purchasing this Luger.

01-28-2013, 12:51 PM	#48
Ben M. User Join Date: Dec 2009 Location: Retired to Naples, FL. Posts: 474 Thanks: 82 Thanked 117 Times in 79 Posts	is seems like the barrel shoulder flange is very thick. is this normal or an indication of a replacement barrel?

01-28-2013, 01:13 PM	#49
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,916 Times in 1,192 Posts	Ben, This is an aftermarket, not quite finished barrel that someone placed on the gun and force matched with spurious barrel markings. You are correct in that the flange is too thick.

01-28-2013, 11:41 PM	#50
Classic Captain User Join Date: Dec 2012 Posts: 56 Thanks: 1 Thanked 0 Times in 0 Posts	Had I known you were in Miami , Alanint . I would have had you inspect it. I am in Miami Beach.

01-29-2013, 05:27 AM	#51
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,916 Times in 1,192 Posts	I would have been glad to take a look, although I am no expert.