my profile |
register |
faq |
search upload photo | donate | calendar |
01-14-2024, 07:09 PM | #1 |
User
Join Date: Sep 2023
Posts: 28
Thanks: 12
Thanked 45 Times in 13 Posts
|
Round Marks on 1942 byf Luger
I remember reading about these but don’t remember where. Can someone tell me the significance of these marks? THANKS!
|
01-14-2024, 07:10 PM | #2 |
User
Join Date: Sep 2023
Posts: 28
Thanks: 12
Thanked 45 Times in 13 Posts
|
Struggling to add photos.
|
01-14-2024, 08:32 PM | #3 |
Super Moderator
Eternal Lifer LugerForum Patron Join Date: Jun 2002
Location: North of Spokane, WA
Posts: 15,926
Thanks: 2,014
Thanked 4,523 Times in 2,089 Posts
|
welcome to the forum!
You should be able to upload right to the forum, there will be a pop-up and then you upload the photos. Ed
__________________
Edward Tinker ************ Co-Author of Police Lugers - Co-Author of Simson Lugers Author of Veteran Bring Backs Vol I, Vol II, Vol III and Vol IV |
01-16-2024, 10:30 PM | #4 |
Super Moderator
Eternal Lifer LugerForum Patron Join Date: Jun 2002
Location: North of Spokane, WA
Posts: 15,926
Thanks: 2,014
Thanked 4,523 Times in 2,089 Posts
|
Here are Fred's pictures
|
The following 3 members says Thank You to Edward Tinker for your post: |
01-16-2024, 11:09 PM | #5 |
User
Join Date: Jun 2009
Location: Massachusetts
Posts: 37
Thanks: 14
Thanked 37 Times in 16 Posts
|
those are tooling marks left from machining the recess.
__________________
-Peter |
01-17-2024, 08:40 AM | #6 |
User
Join Date: Aug 2023
Posts: 73
Thanks: 18
Thanked 56 Times in 34 Posts
|
Agreed. Most likely from an end-mill cutter.
|
The following 2 members says Thank You to velodog455~ for your post: |
01-17-2024, 10:42 AM | #7 |
User
Join Date: Apr 2016
Location: Newburgh,IN
Posts: 787
Thanks: 390
Thanked 627 Times in 332 Posts
|
Fritz, the Mauser machinist, had a bit too much beer the night before and got a little sloppy with his work. Me thinks.
__________________
“God created war so that Americans would learn geography.” ― Mark Twain |
The following member says Thank You to Eugen for your post: |
01-17-2024, 07:41 PM | #8 |
User
Join Date: Sep 2023
Posts: 28
Thanks: 12
Thanked 45 Times in 13 Posts
|
Thanks to all for chiming in, and especially to Ed for helping with my photos. I recently acquired this BW and this was the biggest question about the Luger.
On a side note, I’m wondering if there is a Recovery Group for Luger addicts? I wanted ONE (1) Luger. I’m now at 8. I’m going to the po’ house … but I’m going well-armed! |
01-17-2024, 08:01 PM | #9 |
User
Join Date: Apr 2018
Posts: 287
Thanks: 686
Thanked 668 Times in 173 Posts
|
As Gunbugs once posted, something close to: "We don't seek a cure, just control". Welcome to the addiction.
|
The following 3 members says Thank You to sdmark777 for your post: |
01-17-2024, 10:58 PM | #10 | |
User
Join Date: Jun 2009
Location: Massachusetts
Posts: 37
Thanks: 14
Thanked 37 Times in 16 Posts
|
Quote:
Tooling marks can also be seen on this C96.
__________________
-Peter |
|
The following 2 members says Thank You to Peter S for your post: |
01-18-2024, 02:36 AM | #11 |
Lifer
Lifetime Forum Patron Join Date: Sep 2020
Location: Winnipeg, Canada
Posts: 617
Thanks: 3,053
Thanked 1,057 Times in 429 Posts
|
velodog455~ is correct the marks are from an end mill machining process.
Luger's that have them have not gone through the final finishing stage ... this was due to war time manufacturing where the finish of the gun was less important than getting the gun to the soldiers @ the front. I have never seen these milling marks on commercial Luger's but its possible. As for your 'addiction' just be thankful you aren't addicted to collecting teaspoons or beer cans etc,
__________________
Whoever said that "money can't buy you happiness" never bought a Luger. WTB - Take Down Lever & Trigger Plate (#90) for an Imperial Artillery.
|
01-30-2024, 10:14 PM | #13 | |
User
Join Date: Sep 2023
Posts: 28
Thanks: 12
Thanked 45 Times in 13 Posts
|
Quote:
|
|
The following 4 members says Thank You to Fred Patterson for your post: |
02-28-2024, 12:10 PM | #14 |
Banned
Join Date: Feb 2024
Location: northwest Montana in a remote area.
Posts: 96
Thanks: 0
Thanked 66 Times in 27 Posts
|
Fred
You have a beautiful 42 byf luger there. I have a byf 42 as well with a little more original bluing on mine. Mine has the wooden grip panels that match the number on the gun. If you would like to see some photos let me know. |
03-14-2024, 06:02 AM | #15 |
User
Join Date: Jan 2003
Location: South Florida
Posts: 789
Thanks: 0
Thanked 84 Times in 34 Posts
|
all of the above info is true concerning the "END MILL" cutting tool, however those marks appear to me to be caused by the "END MILL" flexing as it cuts the material, which usually results from the speed of the bit as it though the material in relation to the speed in which the bit is turning.
even a sharp bit being pushed through the material faster than the bit can cut will result in the bit flexing leaving gouge marks deeper than the level that the bit is set at. just my 2 cents
__________________
The "truth" is a matter of Perception |
The following 2 members says Thank You to jamese for your post: |
Thread Tools | |
Display Modes | |
|
|