my profile |
register |
faq |
search upload photo | donate | calendar |
03-24-2018, 05:30 PM | #1 |
User
Join Date: Dec 2017
Posts: 66
Thanks: 4
Thanked 23 Times in 13 Posts
|
Ugly Stovepipe
Shot my 1916 DWM for the second time today. I experienced a problematic malfunction - a stovepipe combined with a round which became partially stripped from the magazine. A round had been stripped and chambered ; perhaps while pulling the toggle back to dislodge the stovepiped casing I engaged a second round from the mag? So , what I had once I had cleared stuck casing was a chambered round , plus another round which was half in - half out of the magazine , and lodged up against the chambered round. The result was that I could not drop the mag because it was still holding on to the back half of the round , and could not clear the second round for the same reason. Naturally , the toggle was trying to do it's job of pushing the round forward , and , unable to climb the feed ramp the bullet of the secound round came to rest tightly under the rim of the chambered round. Round two was really tight. (Wordy , but I think I have described the situation ...)
I found that I could not hold the toggle tight back and free up a hand to dislodge the second round , because the toggle hold back maneuver is a two handed operation. I found myself wishing that there was a hold-open mechanism which could be manually engaged despite a loaded magazine. I found that I wish I had paid closer attention to my father cursing in German years back , as it would have been appropriate in my situation. After some trial and error -with no small degree of discomfort dealing with a hot , jammed weapon , I opted to brace the grip against a piece of cardboard on the ground , force the toggle fully back with one hand , and pry the stuck second round free with a small screw driver. Not the safest thing I have ever done , but better than driving home with the hot gun - which was out of the question. So , comments as to prevention of a reoccurence? Better way of dealing with the situation? Similar experiences to share? Standing by , 'Ski |
03-24-2018, 05:38 PM | #2 |
Patron
LugerForum Patron Join Date: Nov 2008
Posts: 4,047
Thanks: 578
Thanked 1,414 Times in 887 Posts
|
Not exactly clear why you couldn't hold the toggle all the way to the rear with your left hand and then release the magazine to clear part of the problem. But regardless, I'm wondering about the condition of your magazine to let everything go wrong at the same time. OEM magazine or Mec-Gar?
dju |
The following member says Thank You to DavidJayUden for your post: |
03-24-2018, 06:21 PM | #3 |
User
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,681
Thanks: 1,441
Thanked 4,350 Times in 2,040 Posts
|
That situation happens with a luger; most anytime the round is only part way out of the magazine.
I never shoot alone, as one never knows what might go wrong. Because of this practice, I control the luger and have my buddy help extract the magazine. I also carry a "stick" and a screw driver! Such a jam is usually due to "weak" recoil; the empty is not fully ejected but the bolt is far enough back to strip the next round- or the ejector is at fault. Or the shooter "limp" wristed on that shot.
__________________
03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie |
The following member says Thank You to DonVoigt for your post: |
03-24-2018, 07:10 PM | #4 |
Super Moderator
Eternal Lifer LugerForum Patron Join Date: Jun 2002
Location: North of Spokane, WA
Posts: 15,926
Thanks: 2,014
Thanked 4,523 Times in 2,089 Posts
|
I almost always shoot alone Don
What I do is hold with my left hand, aiming downrange, from the front of the frame, left hand. Right hand, I pull the toggle back, left hand thumbing the mag release. Tilt right and it drops the round Going by memory since its been a bit since I shot / had a stovepipe.... |
03-24-2018, 07:39 PM | #5 | |
User
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,681
Thanks: 1,441
Thanked 4,350 Times in 2,040 Posts
|
Quote:
Shooting alone is a personal choice, when you get to be "old" you may change your mind! I never thought about it in the past, but now I do! Especially since I work on all sorts of weapons that require test firing, one never knows when one of them may cause a problem. It is amazing what folks can do to screw up a pistol or a rifle, getting them sorted out quite often takes more than two hands!
__________________
03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie |
|
03-25-2018, 12:10 AM | #6 |
Twice a Lifer
Lifetime Forum Patron Join Date: Mar 2011
Location: Atop the highest hill in Schuyler County NY
Posts: 3,332
Thanks: 7,231
Thanked 2,549 Times in 1,356 Posts
|
This is a 3-handed job. (BY all means, keep that baby pointed downrange!) Didn't John Martz invent something for this? Anyway, a 1916 should have a relieved sear bar, which allows manipulation of the action while the safety is on.
__________________
"... Liberty is the seed and soil, the air and light, the dew and rain of progress, love and joy."-- Robert Greene Ingersoll 1894 |
03-25-2018, 09:01 AM | #7 | |
User
Join Date: Dec 2017
Posts: 66
Thanks: 4
Thanked 23 Times in 13 Posts
|
Quote:
To clarify , the pistol managed to chamber a round during the course of the failed ejection. Upon clearing the stove pipe I found that the next round had been stripped about halfway from the magazine ; as the bullet of that round encountered the feed ramp it lodged underneath the chambered round. Therefor , the magazine could not drop because it was still holding the aft end of round 2 , and round two was rather securely held in place by the magazine in the aft end , and the chambered round in the forward end. Mag would not drop , round two firmly lodged in place. The result was a sticky wicket , as the Brits might say. As to the magazine involved , I was rotating between an old magazine which came with the 1916 , and a new MecGar. To be honest , in the heat of the moment , dealing with an uncomfortable situation with which I had no previous experience , I lost track of which mag was which. I will test shoot both magazines again today and report back. |
|
03-25-2018, 09:17 AM | #8 | |
User
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,681
Thanks: 1,441
Thanked 4,350 Times in 2,040 Posts
|
Quote:
I don't remember where or who, or maybe I just dreamed it? It would not be so complicated to do, but then- it is only rarely necessary or helpful .
__________________
03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie |
|
03-25-2018, 11:55 AM | #9 |
User
Join Date: Dec 2017
Posts: 66
Thanks: 4
Thanked 23 Times in 13 Posts
|
Addendum:
I have to think that the half in half out of the mag second round resulted from my drawing the toggle back to free the stovepipe. It did not occur to me at the time that that might happen. In light of that , I plan to practice to avoid such an event in the future. Using Snap Caps , I will insert a round into the chamber , magazine removed , then ease the toggle forward to pin a stovepipe. Next I will insert a Snap Cap loaded mag and practice freeing the stovepipe without drawing the toggle assembly so far back that it strips a following round. I would think that this is doable. In my past experiences with stovepipes in other semi-autos I have not had this situation occur. Also , most semis allow the shooter to lock the slide fully rearward without the influence of a magazine. In short , I am still learning the Luger. |
03-25-2018, 12:16 PM | #10 |
User
Join Date: Nov 2008
Location: Upstate NY
Posts: 30
Thanks: 135
Thanked 13 Times in 7 Posts
|
What I have learned is the first thing I do with a stove pipe is drop the magazine, then pull the toggle back which allows spent round and chambered round to drop out.
|
The following member says Thank You to CRob for your post: |
03-25-2018, 01:05 PM | #11 |
User
Join Date: Dec 2017
Posts: 66
Thanks: 4
Thanked 23 Times in 13 Posts
|
|
03-25-2018, 01:25 PM | #12 | |
User
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,681
Thanks: 1,441
Thanked 4,350 Times in 2,040 Posts
|
Quote:
__________________
03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie |
|
03-25-2018, 03:09 PM | #13 |
Super Moderator - Patron
LugerForum Life Patron Join Date: Dec 2009
Location: Eastern North Carolina, USA
Posts: 3,907
Thanks: 1,374
Thanked 3,108 Times in 1,509 Posts
|
Put some masking tape on the back of the frame under the place where the receiver toggle contacts it and the frame stops the toggle.
Load a single round, and manually cycle it into the Luger. Leave the magazine in place With a single round chambered and the magazine in place, aim and fire the Luger while focusing on a good supporting hold in which the recoil force will travel back through your bones and your body absorbs the recoil. Check the tape to see if there is excessive force against the frame, no force against the frame or just a little. Repeat the exercise a few times after changing the masking tape. This will help you understand if the toggle mechanism is being driven back with too little or too much force, and will help you judge your grip. If you can just see the marks from the toggle on the tape, the recoil spring and balance is probably pretty close to being correct for the ammunition you're using. If this is consistently the case, look to the magazine and also to your grip as the possible source of the feeding problems. If everything is correct, load two rounds, chamber one manually and fire two. Observe the masking tape. Feel the recoil impulse. if this works, try with three rounds. Continue until the stovepipe / misfeeds return or things are working properly. The Luger is a balanced mechanism where too little or too much recoil compensation can lead to feed problems. Always address your stance and hold before you start changing out things. Then start with a known good magazine. The best in my experience are the wartime or post war DDR Haenel Schmeisser / Thalmann manufactured "fxo" "E/37" or "1001/2" marked magazines.
__________________
Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war. |
The following member says Thank You to mrerick for your post: |
03-25-2018, 06:12 PM | #14 |
User
Join Date: Dec 2017
Posts: 66
Thanks: 4
Thanked 23 Times in 13 Posts
|
mrerick ,
Thank you for that detailed analysis and tutorial. I shall make it the basis for a project next weekend. I ran 60 rounds thru my Luger today without incident , 20 each from 3 different magazines. My round total for this pistol is approx. 150 ; 1 stovepipe out 150 constitutes an isolated incident , I think , compounded by my learning curve. So it goes. I included a couple of images for show & tell. I was set up at 25 ft. I achieved a reasonable grouping once I settled down. Also shown are my VOPO shooting grips. They look good enough that I am in no hurry to put the originals back on. Thanks for your help. 'Ski |
The following 2 members says Thank You to Waveski for your post: |
03-25-2018, 07:25 PM | #15 |
User
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,681
Thanks: 1,441
Thanked 4,350 Times in 2,040 Posts
|
I don't think you have a problem.
I agree that for shooting the Vopo grips are just fine.
__________________
03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie |
03-26-2018, 06:25 PM | #16 | |
User
Join Date: Sep 2007
Posts: 1,225
Thanks: 2,679
Thanked 930 Times in 509 Posts
|
Quote:
1 open the action the usual away. 2 use your right hand to keep the action open like on photo. 3 your left hand is now free. You can push the cartridge back into the magazine with your index and release the magazine with your thumb. You can now easily remove the spent cartridge from the chamber. Once in a while I had this type of jam. Not because of stovepiping but because the extractor released the case early leaving it halfway out the chamber(it was ammo related). First time it ocurred was in a match. I had to declare an alibi, that cost me 2 points penalty, in a 5 minute 5 shot string because I couldn't clear it alone. When I got home I decided it wouldn't happen again. So I developed this method. |
|
The following 8 members says Thank You to kurusu for your post: |
03-27-2018, 10:00 AM | #17 |
Moderator
2010 LugerForum Patron Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,012
Thanks: 1,088
Thanked 5,154 Times in 1,696 Posts
|
Mario,
That is an interesting marking on the frame panel. Can you tell us what it is? Thanks, Ron
__________________
If it's made after 1918...it's a reproduction |
03-27-2018, 11:04 AM | #18 |
Lifer
Lifetime Forum Patron Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,182
Thanks: 1,400
Thanked 4,442 Times in 2,330 Posts
|
Sounds like the Martz Safe Toggle Release (US Patent #3,956,967).
__________________
I like my coffee the way I like my women... ...Cold and bitter... |
The following member says Thank You to sheepherder for your post: |
03-27-2018, 11:19 AM | #19 |
Patron
LugerForum Patron Join Date: Jun 2002
Location: POB 398 St.Charles,MO. 63302
Posts: 5,089
Thanks: 6
Thanked 736 Times in 483 Posts
|
M, Your method of clearing the chamber is what I always use for PO8 take down, rather than risking damaging the barrel crown by pushing it against a hard surface. when an empty mag is not available. I believe that I saw it in an old PO8 manual. The MSTR works by connecting the safety to a modified hold open, TH
|
The following member says Thank You to Lugerdoc for your post: |
03-27-2018, 11:50 AM | #20 | |
Lifer
Lifetime Forum Patron Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,182
Thanks: 1,400
Thanked 4,442 Times in 2,330 Posts
|
Quote:
I know there are a couple members here who collect Martz conversions, and Martz stamped MSTR on the side of the modified Lugers. Maybe one of those could tell us how it operated??? ("junglejim" was one, I think)... Edit: Here's the full MSTR patent file...
__________________
I like my coffee the way I like my women... ...Cold and bitter... |
|
|
|