Wide Trigger?

Dwight Gruber · 11-22-2003, 01:16 AM

I seem to recall reading about a wide trigger variation on early Lugers, but can't find the reference.

Could someone inform me on the matter? What are its characteristics, what should I look for to identify one? What model Luger is it found on? How common (or uncommon) is it, and if I should run across one, what should I expect it to add to the value of the Luger?

Thanks in advance for anybody's help.

--Dwight

Doubs · 11-22-2003, 01:18 AM

Dwight, I don't have the book in front of me but Kenyon's "Lugers at Random" has comparison pictures of the triggers.

Ron Wood · 11-22-2003, 01:43 AM

It is found on the 1900 Swiss, primarily in the 4000 range but examples exist well outside that range (I have 3185). They are relatively scarce. There are a number of suggestions concerning the wide trigger, that it was for marksmanship teams, a design trial to improve the "feel" of the trigger, and/or to make the trigger pull the same for a right or left handed shooter. Any one or all of these may be correct.

The trigger is the full width of the trigger guard and looks pretty impressive. The last two digits of the serial number are marked on the upper left side of the trigger and are visible when the gun is assembled. According to the "books" a wide trigger adds 15%-20% to the value of the Luger.

Pete Ebbink · 11-22-2003, 11:38 AM

To add to Ron's great info. posting :

(Click on the small photo to blow-up to a larger view...and then click on the expand button in the right-lower corner of the 2nd. photo view to get an even larger view...)

Photo is from V. Bobb'a book on Swiss lugers, from page 192.

<a href="http://forums.lugerforum.com/lfupload/triggertypes1001.jpg" target="_fullview"><img src="http://forums.lugerforum.com/lfupload/triggertypes1001.jpg" width="400" alt="Click for fullsize image" /></a>

Regards,

Pete... <img border="0" alt="[typing]" title="" src="graemlins/yltype.gif" />

Dwight Gruber · 11-22-2003, 06:40 PM

Curiosity assuaged, thanks to all.

--Dwight

Pete Ebbink · 01-18-2004, 05:09 PM

Ron and others,

Regarding left-handed shooting...

Is there any info. regarding or have any lugers shown up with the magazine release button "reversed"...so a thumb on the left hand can drop out a magazine...?

Wondered if the skilled gunsmiths in Switzerland reworked some for their left-handed shooting clients...?

Just curious...?

Pete... <img border="0" alt="[typing]" title="" src="graemlins/yltype.gif" />

ViggoG · 01-19-2004, 02:56 AM

Pete,
I for one am not left handed, however I am somewhat ambidexterous in a small way, bowling, Pistol shooting, handsawing, fileing and a few others.
It all began in my machine shop work, comes in handy for sawing or fileing lathe tooled cylinderical work in the lathe.
With this said, I find that the magazine release to be quite comfortable to release with my left index or midddle finger, and were I a "lefty" I can see no need to make such an alteration.
Just my Opinion.
ViggoG

John Sabato · 01-19-2004, 07:39 AM

Such a modification would of course also require the manufacture of magazines with the latch cutout on the opposite side... That would be a pretty good manufacturing expense in tooling for such a small demand item...

hmmmm, now that I have brought that up, does anyone know much about the sheet metal fabrication of the magazine. Do you think the mag latch hole was "punched" before or after the mag was assembled?

(This ought to be a pretty good discussion!)

Vlim · 01-19-2004, 08:56 AM

Hi John,

For the dutch-made postwar magazines (supplied with the mauser parabellums) the answer is 'before'.

I have seen some half-made products left over from the company that produced them, one of these is a simple folded sheet with no profile or holes whatsoever, except for the latch hole.

John Sabato · 01-20-2004, 01:26 PM

Gerben, that would have been my guess, but sometimes things are done the way the were "always" done in the old days... and I don't think any documentation exists (or at least I don't personally know of any) that tells how sheet metal mags were manufactured in Europe duing the first half of the last century...

With today's computer engineered technology, virtually all holes would be punched in any metal that gets formed cold. I managed an engineering department for a very technology sophisticated sheet metal manufacturer for two years and the wealth of knowledge that I acquired on state-of-the-art manufacturing methods was worth the meager salary that I earned while there... I was much richer for the experience.

Vlim · 01-20-2004, 03:44 PM

Some additional info on the Dutch 'Mauser' postwar mags as deduced from some left-over halfproducts:

First part was to create both halves of the magazine, from flat plates, where the latch hole was cut before bending.

Second part was to put both halves together and crimp them (creating the lengthwise crimp that also serves as a guide rail for the loading tool). The holes for the button were added, as well as the attaching holes for the button.

After that, the crimpline was dented crosswise, just below the top (to keep both halves in place, I guess) and the lips at the top would be formed correctly. After that step the slit for the follower was added.

Final production steps involved coating the magazine tubes. Final assembly was later done at Mauser.

It's not known whether this production method followed earlier methods. I believe they started from scratch, using the original blueprints (supplied by Mauser) as a guideline, followed by using the extruded Haenel (also supplied by Mauser) as a dimensional model.

The first examples, based upon the original 30s blueprints proved to be extremely unreliable and Mauser sent them an extruded Haenel mag to serve as a dimensional guideline. Some corrections were made to the design and this is the version that can be found labeled 'Mauser' and/or 'Made in Holland'.

11-22-2003, 01:16 AM	#1
Dwight Gruber User Join Date: Jun 2002 Location: Portland, Oregon Posts: 3,890 Thanks: 0 Thanked 1,282 Times in 424 Posts	Wide Trigger? I seem to recall reading about a wide trigger variation on early Lugers, but can't find the reference. Could someone inform me on the matter? What are its characteristics, what should I look for to identify one? What model Luger is it found on? How common (or uncommon) is it, and if I should run across one, what should I expect it to add to the value of the Luger? Thanks in advance for anybody's help. --Dwight

11-22-2003, 01:43 AM	#3
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 6,988 Thanks: 1,067 Thanked 5,097 Times in 1,676 Posts	It is found on the 1900 Swiss, primarily in the 4000 range but examples exist well outside that range (I have 3185). They are relatively scarce. There are a number of suggestions concerning the wide trigger, that it was for marksmanship teams, a design trial to improve the "feel" of the trigger, and/or to make the trigger pull the same for a right or left handed shooter. Any one or all of these may be correct. The trigger is the full width of the trigger guard and looks pretty impressive. The last two digits of the serial number are marked on the upper left side of the trigger and are visible when the gun is assembled. According to the "books" a wide trigger adds 15%-20% to the value of the Luger. __________________ If it's made after 1918...it's a reproduction

01-19-2004, 07:39 AM	#8
John Sabato Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: The Capital of the Free World Posts: 10,150 Thanks: 3,003 Thanked 2,304 Times in 1,096 Posts	Such a modification would of course also require the manufacture of magazines with the latch cutout on the opposite side... That would be a pretty good manufacturing expense in tooling for such a small demand item... hmmmm, now that I have brought that up, does anyone know much about the sheet metal fabrication of the magazine. Do you think the mag latch hole was "punched" before or after the mag was assembled? (This ought to be a pretty good discussion!) __________________ regards, -John S "...We hold these truths to be self-evident that ALL men are created EQUAL *and are endowed by their Creator* with certain UNALIENABLE* rights, and among these are life, LIBERTY, and the pursuit of happiness..."*

01-20-2004, 01:26 PM	#10
John Sabato Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: The Capital of the Free World Posts: 10,150 Thanks: 3,003 Thanked 2,304 Times in 1,096 Posts	Gerben, that would have been my guess, but sometimes things are done the way the were "always" done in the old days... and I don't think any documentation exists (or at least I don't personally know of any) that tells how sheet metal mags were manufactured in Europe duing the first half of the last century... With today's computer engineered technology, virtually all holes would be punched in any metal that gets formed cold. I managed an engineering department for a very technology sophisticated sheet metal manufacturer for two years and the wealth of knowledge that I acquired on state-of-the-art manufacturing methods was worth the meager salary that I earned while there... I was much richer for the experience. __________________ regards, -John S "...We hold these truths to be self-evident that ALL men are created EQUAL *and are endowed by their Creator* with certain UNALIENABLE* rights, and among these are life, LIBERTY, and the pursuit of happiness..."*

11-22-2003, 01:18 AM	#2
Doubs User Join Date: Jun 2002 Location: Byron, Georgia Posts: 1,670 Thanks: 770 Thanked 1,614 Times in 525 Posts	Dwight, I don't have the book in front of me but Kenyon's "Lugers at Random" has comparison pictures of the triggers.

11-22-2003, 11:38 AM	#4
Pete Ebbink User Join Date: Jun 2002 Location: The USA Posts: 5,919 Thanks: 0 Thanked 6 Times in 4 Posts	To add to Ron's great info. posting : (Click on the small photo to blow-up to a larger view...and then click on the expand button in the right-lower corner of the 2nd. photo view to get an even larger view...) Photo is from V. Bobb'a book on Swiss lugers, from page 192. <a href="http://forums.lugerforum.com/lfupload/triggertypes1001.jpg" target="_fullview"><img src="http://forums.lugerforum.com/lfupload/triggertypes1001.jpg" width="400" alt="Click for fullsize image" /></a> Regards, Pete... <img border="0" alt="[typing]" title="" src="graemlins/yltype.gif" />

11-22-2003, 06:40 PM	#5
Dwight Gruber User Join Date: Jun 2002 Location: Portland, Oregon Posts: 3,890 Thanks: 0 Thanked 1,282 Times in 424 Posts	Curiosity assuaged, thanks to all. --Dwight

01-18-2004, 05:09 PM	#6
Pete Ebbink User Join Date: Jun 2002 Location: The USA Posts: 5,919 Thanks: 0 Thanked 6 Times in 4 Posts	Ron and others, Regarding left-handed shooting... Is there any info. regarding or have any lugers shown up with the magazine release button "reversed"...so a thumb on the left hand can drop out a magazine...? Wondered if the skilled gunsmiths in Switzerland reworked some for their left-handed shooting clients...? Just curious...? Pete... <img border="0" alt="[typing]" title="" src="graemlins/yltype.gif" />

01-19-2004, 02:56 AM	#7
ViggoG RIP Join Date: Jun 2002 Location: South Side Virginia Posts: 534 Thanks: 0 Thanked 1 Time in 1 Post	Pete, I for one am not left handed, however I am somewhat ambidexterous in a small way, bowling, Pistol shooting, handsawing, fileing and a few others. It all began in my machine shop work, comes in handy for sawing or fileing lathe tooled cylinderical work in the lathe. With this said, I find that the magazine release to be quite comfortable to release with my left index or midddle finger, and were I a "lefty" I can see no need to make such an alteration. Just my Opinion. ViggoG

01-19-2004, 08:56 AM	#9
Vlim Moderator Lifetime LugerForum Patron Join Date: Oct 2002 Location: Europe Posts: 5,038 Thanks: 1,021 Thanked 3,900 Times in 1,190 Posts	Hi John, For the dutch-made postwar magazines (supplied with the mauser parabellums) the answer is 'before'. I have seen some half-made products left over from the company that produced them, one of these is a simple folded sheet with no profile or holes whatsoever, except for the latch hole.

01-20-2004, 03:44 PM	#11
Vlim Moderator Lifetime LugerForum Patron Join Date: Oct 2002 Location: Europe Posts: 5,038 Thanks: 1,021 Thanked 3,900 Times in 1,190 Posts	Some additional info on the Dutch 'Mauser' postwar mags as deduced from some left-over halfproducts: First part was to create both halves of the magazine, from flat plates, where the latch hole was cut before bending. Second part was to put both halves together and crimp them (creating the lengthwise crimp that also serves as a guide rail for the loading tool). The holes for the button were added, as well as the attaching holes for the button. After that, the crimpline was dented crosswise, just below the top (to keep both halves in place, I guess) and the lips at the top would be formed correctly. After that step the slit for the follower was added. Final production steps involved coating the magazine tubes. Final assembly was later done at Mauser. It's not known whether this production method followed earlier methods. I believe they started from scratch, using the original blueprints (supplied by Mauser) as a guideline, followed by using the extruded Haenel (also supplied by Mauser) as a dimensional model. The first examples, based upon the original 30s blueprints proved to be extremely unreliable and Mauser sent them an extruded Haenel mag to serve as a dimensional guideline. Some corrections were made to the design and this is the version that can be found labeled 'Mauser' and/or 'Made in Holland'.