parts source for Stoeger 9mm Lugers

DavidJayUden · 11-26-2008, 10:41 PM

A friend has a Stainless Stoeger American Eagle Kuger that shows signs of damage to both the inside of the side plate and also to the trigger. Are there any sources of parts for these?
Thanks;
David Uden

Vlim · 11-27-2008, 11:20 AM

It's best to fit a new luger between the grip screws.

These particular guns are not known for their quality and durability and finding correct parts could be difficult. The steel used is too soft and the final fitting is usually poor, causing all sorts of problems.

11-27-2008, 11:23 AM

In the links and resources section there is some contact information...
R.E. Romo, Orimar Corp, PO box 8767, Houston,TX 77249-8767, (713) 305-8540
Current Reproduction Stainless Steel Lugers (Former producer of Mitchell, Stoeger and AIMCO Stainless Steel Lugers)

Not sure if it is current or not. It would probably be best to try and call and see if you can talk to Mr. Romo.

Good luck.

Drachenstein · 12-04-2008, 08:57 PM

713-305-8540 is the current number, good luck.

John Sabato · 12-05-2008, 10:34 AM

I understand that the same number is also used for a FAX if it isn't answered in a few rings. You could also try sending a fax to that number with your request.

11-26-2008, 10:41 PM	#1
DavidJayUden Patron LugerForum Patron Join Date: Nov 2008 Posts: 4,047 Thanks: 578 Thanked 1,414 Times in 887 Posts	parts source for Stoeger 9mm Lugers A friend has a Stainless Stoeger American Eagle Kuger that shows signs of damage to both the inside of the side plate and also to the trigger. Are there any sources of parts for these? Thanks; David Uden

12-05-2008, 10:34 AM	#5
John Sabato Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: The Capital of the Free World Posts: 10,150 Thanks: 3,003 Thanked 2,304 Times in 1,096 Posts	I understand that the same number is also used for a FAX if it isn't answered in a few rings. You could also try sending a fax to that number with your request. __________________ regards, -John S "...We hold these truths to be self-evident that ALL men are created EQUAL *and are endowed by their Creator* with certain UNALIENABLE* rights, and among these are life, LIBERTY, and the pursuit of happiness..."*

11-27-2008, 11:20 AM	#2
Vlim Moderator Lifetime LugerForum Patron Join Date: Oct 2002 Location: Europe Posts: 5,034 Thanks: 1,019 Thanked 3,882 Times in 1,186 Posts	It's best to fit a new luger between the grip screws. These particular guns are not known for their quality and durability and finding correct parts could be difficult. The steel used is too soft and the final fitting is usually poor, causing all sorts of problems.

11-27-2008, 11:23 AM	#3
Brad Guest Posts: n/a	In the links and resources section there is some contact information... R.E. Romo, Orimar Corp, PO box 8767, Houston,TX 77249-8767, (713) 305-8540 Current Reproduction Stainless Steel Lugers (Former producer of Mitchell, Stoeger and AIMCO Stainless Steel Lugers) Not sure if it is current or not. It would probably be best to try and call and see if you can talk to Mr. Romo. Good luck.

12-04-2008, 08:57 PM	#4
Drachenstein User Join Date: Nov 2008 Location: Elizabethtown, KY Posts: 78 Thanks: 0 Thanked 1 Time in 1 Post	713-305-8540 is the current number, good luck.