LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > Research Archives > Early Lugers (1900-1906)

 
Thread Tools Display Modes
Unread 03-08-2004, 07:36 PM   #1
Ron Wood
Moderator
2010 LugerForum
Patron
 
Ron Wood's Avatar
 
Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,010
Thanks: 1,088
Thanked 5,149 Times in 1,694 Posts
Post Early Frame Tutorial

Most of our Luger Forum members are familiar with the designation of "Long Frame" and "Short Frame". The "long" frame and receiver is 1mm longer than the "short" frame and receiver, with the extra length occurring in front of the takedown lever. The threaded portion of the long and short frame barrels are also 2mm different in length and therefore are not interchangeable.

However, some beginning Luger fans may not be aware that during early Luger development there were several transition steps from the old model long frame to the new model short frame.

Here are Type categorizations of these transition steps that I have made into a little guide. These are my observations and I am sure this list may not be totally comprehensive and that exceptions do exist (all bets are off on 1920 era Lugers), but it is by and large representative. I welcome any recommended corrections, changes or comments.

Type I - Old model long frame, thick rounded frame and trigger guard the full width of the frame. Type I is found on 1900 military and commercial Lugers, 1900 and 1902 Carbines, some 1902 Prototypes, and the 1904 Navy (with the addition of a stock lug).



Type II - Old model short frame, squared off frame, trigger guard the full width of the frame, and "thin" frame below the takedown lever. Type II is found on 1902 commercial, American Eagle, and test Lugers (Dutch, German, and American Eagle), some 1902 Prototypes, and 1903 Commercial.



Type III - New model long frame, rounded frame with rebated trigger guard (trigger guard machined narrower than the frame). Type III is found on 1906 Navy, early 1906 commercial and American Eagle (some safety marked and some with stock lug), 1906 Swiss (DWM Cross in Sunburst, DWM Cross in Shield and Waffenfabrik Bern produced).



Type IV - New model short frame, squared off thin frame, rebated trigger guard. Type IV is found on early 1906 9mm Lugers (Commercial, American Eagle, Russian) and the 1907 .45 Caliber Test Luger. Also found on 1906 7.65mm Lugers such as: 1906 Bulgarian, M2 Portuguese, some Commercial, and some Swiss.



Type V - New model short frame, squared off thick frame (with the thicker area below the takedown lever), rebated trigger guard. Type V is found on virtually all Lugers produced after 1908, to include commercial and contract Lugers of the 1906 pattern with grip safety.

__________________
If it's made after 1918...it's a reproduction

Last edited by Ron Wood; 12-22-2018 at 05:05 PM.
Ron Wood is offline  
The following 2 members says Thank You to Ron Wood for your post:
Unread 03-08-2004, 11:05 PM   #2
Dwight Gruber
User
 
Join Date: Jun 2002
Location: Portland, Oregon
Posts: 3,894
Thanks: 0
Thanked 1,288 Times in 426 Posts
Post

Ron,

Thanks for the really excellent and informative tutorial. I have a couple of questions.

What frame details would one find on a 1904 Navy?

In Type II, to what 1902 American Eagle Test Lugers do you refer?

--Dwight
Dwight Gruber is offline  
Unread 03-09-2004, 02:29 AM   #3
Ron Wood
Moderator
2010 LugerForum
Patron
 
Ron Wood's Avatar
 
Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,010
Thanks: 1,088
Thanked 5,149 Times in 1,694 Posts
Post

Dwight,

The 1904 Navy frame is the old model flat laminated mainspring type "long" frame BUT with the addition of a stock lug. I will add the 1904 Navy to the Type I examples. Thank you.

The 1902 US Test Cartridge Counter Lugers had the American Eagle over the chamber.
__________________
If it's made after 1918...it's a reproduction
Ron Wood is offline  
Unread 03-09-2004, 08:02 AM   #4
Vlim
Moderator
Lifetime
LugerForum Patron
 
Vlim's Avatar
 
Join Date: Oct 2002
Location: Europe
Posts: 5,053
Thanks: 1,036
Thanked 3,987 Times in 1,205 Posts
Post

Ron,

Excellent. I immediately pulled the lugers from the safe and was able to find this info:

The 1913 1906-pattern KNIL fits the type V image like a glove.

The 1937 S/42 is slightly different (type VI ?)
in that the rebated trigger guard starts a little lower than on the type V.
Vlim is offline  
Unread 03-09-2004, 11:58 AM   #5
Ron Wood
Moderator
2010 LugerForum
Patron
 
Ron Wood's Avatar
 
Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,010
Thanks: 1,088
Thanked 5,149 Times in 1,694 Posts
Post

Gerben,

Thank you for your comments. Your observation on your S/42 is well taken and is one of the many additional variations that can be found among the different manufacturers. The different shaped transitions from the trigger guard to the front grip strap, the Mauser "hump", the variations in machining the groove in the stock lug - the list goes on and on. I will let that essay to another student of the Luger (mostly because I don't have examples of these "reproduction" Lugers to photograph!).
__________________
If it's made after 1918...it's a reproduction

Last edited by Ron Wood; 05-17-2009 at 01:51 AM.
Ron Wood is offline  
Unread 03-12-2004, 09:52 AM   #6
Balder
User
 
Balder's Avatar
 
Join Date: Jan 2003
Location: Norway
Posts: 288
Thanks: 20
Thanked 34 Times in 19 Posts
Post

Ron,

Very interesting and educational - thanks! I had to pull out my Lugers to check. The US Eagle test Luger fits the picture, but I was confused when I looked at my mongrel S/42 from 1938. What I am thinking of is the external little hole for the spring for the takedown lever, just in front of the trigger guard - it's not there. I see that your Type III doesn't seem to have one either, although it could be that the end of the spring is perfectly flush with the hole and doesn't show in the picture. Anyway, I believe my 1938 S/42 should have one, or did they come in different variants? I can't remember what this looked like on the other Lugers that I've owned over the years. Sorry about the picture quality, the Canon Ixus isn't that good on close-ups.

Regards,

Balder
Balder is offline  
Unread 03-12-2004, 10:49 AM   #7
Ron Wood
Moderator
2010 LugerForum
Patron
 
Ron Wood's Avatar
 
Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,010
Thanks: 1,088
Thanked 5,149 Times in 1,694 Posts
Post

Balder, (Edited: While I was composing this masterpiece you have already discovered my observation. I must really try to be more speedy)

Actually, on my Type III example the spring does protrude a wee bit, but from the slightly elevated angle I took the picture it isn't visible.

Your photography is quite good. Unless my eyes deceive me, I do detect the end of the spring that has been finished flush with the frame, and the expected hole is present, just cleverly disguised.

__________________
If it's made after 1918...it's a reproduction
Ron Wood is offline  
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:54 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Lugerforum.com