LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Repairs, Restoration & Refinishing

Reply
Thread Tools Display Modes
Unread 07-11-2011, 08:29 PM   #1
Ronfromflorida
User
 
Join Date: Jul 2011
Posts: 6
Thanks: 6
Thanked 0 Times in 0 Posts
Default Trigger sometimes does not work

Please I know someone here can help me but I am not sue how to post and naviagte the site.
My 1917 Mauser developed a triger problem I can't seem to fix.
Sometimes the weapon fires several shots without problem.
Then sometimes you have to pull the trigger 2 or 3 times before it fires.
Then sometimes I have to pull the bolt back just enough to see the catridge close it up and then it will always fire.
Please someone must know the cause and the fix???
Help Me...
Ronfromflorida is offline   Reply With Quote
Unread 07-11-2011, 09:24 PM   #2
alanint
User
 
alanint's Avatar
 
Join Date: Mar 2008
Location: Marco Island, Florida
Posts: 4,867
Thanks: 1,685
Thanked 1,916 Times in 1,192 Posts
Default

The most probable issue is that the plunger in the end of your sear is not resetting properly. Does it move freely? There may be dirt or debris, which has accumulated in, under or around this little plunger. Clean it thoroughly and see what happens.
alanint is offline   Reply With Quote
The following member says Thank You to alanint for your post:
Unread 07-11-2011, 09:42 PM   #3
lugerholsterrepair
Moderator
Lifetime Forum
Patron
 
lugerholsterrepair's Avatar
 
Join Date: Jun 2002
Location: Arizona/Colorado
Posts: 7,772
Thanks: 4,940
Thanked 3,124 Times in 1,434 Posts
Default

sometimes I have to pull the bolt back just enough to see the cartridge, close it up and then it will always fire.

It does not take much pull back on the toggle to recock the weapon. It might not be recocking after fireing.

I agree a thorough cleaning and lubricating would be a first step.
__________________
Jerry Burney
11491 S. Guadalupe Drive

Yuma AZ 85367-6182


lugerholsterrepair@earthlink.net

928 342-7583 (CO & AZ) Year Round
719 207-3331 (cell)


"For those who Fight For It, Life has a flavor the protected will never know."
lugerholsterrepair is offline   Reply With Quote
The following member says Thank You to lugerholsterrepair for your post:
Unread 07-11-2011, 10:37 PM   #4
command450
User
 
command450's Avatar
 
Join Date: Jun 2011
Location: West Michigan
Posts: 38
Thanks: 16
Thanked 6 Times in 4 Posts
Default

It does sound like a typical(intermittent FTF) gummed up firing pin assembly,inside the toggle.
command450 is offline   Reply With Quote
The following member says Thank You to command450 for your post:
Unread 07-11-2011, 10:52 PM   #5
Ronfromflorida
User
 
Join Date: Jul 2011
Posts: 6
Thanks: 6
Thanked 0 Times in 0 Posts
Default

Thanks guys, I did throughly clean it already and did clean the little plunder in the side of the Toggle assemply but did not clean the firing pin assembly as far as I know 1917 was the last time anyone was in there.
I will try it all thanks guys though I was hoping this was a typical problem others would immediatly recognize.
But I shall try it all thanks for your prompt replys.
Love my Lugar, I was using it a s a carry gun here in Florida but his reliablity problem nixed that. Thanks Ron
Ronfromflorida is offline   Reply With Quote
Unread 07-13-2011, 11:38 AM   #6
SIGP2101
User
 
SIGP2101's Avatar
 
Join Date: Sep 2006
Location: Canada
Posts: 256
Thanks: 74
Thanked 67 Times in 32 Posts
Default

Quote:
Originally Posted by Ronfromflorida View Post
... but did not clean the firing pin assembly as far as I know 1917 was the last time anyone was in there.
wow, remember - trouble shooting starts with a clean gun only.
SIGP2101 is offline   Reply With Quote
The following member says Thank You to SIGP2101 for your post:
Unread 07-15-2011, 11:21 AM   #7
Lugerdoc
Patron
LugerForum
Patron
 
Lugerdoc's Avatar
 
Join Date: Jun 2002
Location: POB 398 St.Charles,MO. 63302
Posts: 5,089
Thanks: 6
Thanked 736 Times in 483 Posts
Default

Ron et al, By definition a 1917 Mauser PO8 would have to be a mismatched shooter. Quite often when putting together such a luger, the parts will not be properly hand fitted. I agree that it sounds like it is not disconnecting properly on recoil. Most likely the trigger lever in the side plate is not allowing the disconnector plunger to pass under it for a second shot. This is common on parts guns and usually requires some fitting of the trigger lever. TH
__________________
Tom Heller POB 398 ST.Charles, MO. 63302
Tel 636-447-3006 lugerdoc@charter.net
Lugerdoc is offline   Reply With Quote
The following 2 members says Thank You to Lugerdoc for your post:
Unread 07-15-2011, 12:25 PM   #8
Thor
User
 
Thor's Avatar
 
Join Date: Jun 2002
Location: Rio Rancho, New Mexico
Posts: 4,583
Thanks: 958
Thanked 970 Times in 276 Posts
Default

Lugerdoc and Alanint are right. Also does the spring power of that small plunger on the end of the sear bar have plenty of power, sometimes those need to be replaced if they are weak or the plunger sticks. The top of the lever Lugerdoc mentioned is probably not moving away from the plunger enough to allow it to reset. Lugerdoc can fix many of these problems.
__________________
Thor's Luger Clinic http://members.rennlist.com/lugerman/
Ted Green (Thor Yaller Boots)
725 Western Hills Dr SE, Rio Rancho, NM 87124
915-526-8925 Email
thor340@aol.com
-----------------------------------
John3:3
Jesus answered and said to him, "Most assuredly, I say to you, unless one is born again, he cannot see the kingdom of God."
Thor is offline   Reply With Quote
Unread 07-15-2011, 02:57 PM   #9
marshombre
User
 
marshombre's Avatar
 
Join Date: Jan 2006
Location: W Central FL
Posts: 98
Thanks: 12
Thanked 20 Times in 11 Posts
Default

You have a Mauser with a 1917 chamber date? I'm no expert, but Mauser did not produce Lugers until the 1930s.
It sounds to me like you have a mixed parts gun with faulty firing pin to sear engagement.
This guy is #1. Lugerdoc aka Tom Heller at <hellerarms@webtv.net>
PM me if you live near Tampa, maybe I can help. Good luck, MR


Marshombre- you post was moved because the original poster duplicated his original message, so you answer may or maynot seem in order as it is the last post on this thread and the first response on the duplicate message. Moderator
__________________
Tempus edax rerum

Last edited by Thor; 07-15-2011 at 05:47 PM. Reason: moved from duplicate post
marshombre is offline   Reply With Quote
The following member says Thank You to marshombre for your post:
Unread 08-03-2011, 10:56 PM   #10
Ronfromflorida
User
 
Join Date: Jul 2011
Posts: 6
Thanks: 6
Thanked 0 Times in 0 Posts
Default Hi marshombre

Yes I live in St Pete. I am going to take it apart tonight and clean the firing pin area.
But I might want your help and would drive over to Tampa for it.\
Thanks for the offer. Ronnie
Ronfromflorida is offline   Reply With Quote
Unread 09-14-2011, 09:04 PM   #11
Ronfromflorida
User
 
Join Date: Jul 2011
Posts: 6
Thanks: 6
Thanked 0 Times in 0 Posts
Default

marshombre is your offer still valid?
I have completely cleaned the thing reassembled it to no avail.
I'll drive where ever in Tampa or St Pete if you will just look at it with me.
Ronnie (727) 471-8936
or rndubs@hotmail.com
Ronfromflorida is offline   Reply With Quote
Unread 09-14-2011, 09:08 PM   #12
Ronfromflorida
User
 
Join Date: Jul 2011
Posts: 6
Thanks: 6
Thanked 0 Times in 0 Posts
Default

Can anyone give me the step by step firing sequence from trigger pull to the reset for the next firing?
Ronfromflorida is offline   Reply With Quote
Unread 09-15-2011, 04:51 PM   #13
SIGP2101
User
 
SIGP2101's Avatar
 
Join Date: Sep 2006
Location: Canada
Posts: 256
Thanks: 74
Thanked 67 Times in 32 Posts
Default

If I could only attach .AVI files you would be able to see entire step by step firing sequence.
SIGP2101 is offline   Reply With Quote
Reply

Tags
1917, fire, mauser, problems, trigger

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:04 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Lugerforum.com