my profile |
register |
faq |
search upload photo | donate | calendar |
08-24-2020, 08:17 PM | #1 |
User
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
|
Issues with reassembly
Hello all,
I recently came into the possession of two 1914 DWM produced Lugers and require some input regarding reassembly. One Luger is a standard size while the other is an Artillery Luger. Both were stored in less than ideal conditions which prompted me to field strip and clean them. (Thankfully no major rust or no damage!) However, I've run into issues during reassembly. On the standard Luger I've noticed that the slide is loose and slides back and forth after I reattach the receiver to the frame and lock the toggle (It does this when the locking bolt and takedown plate are in place, as well as not in place.) I've ensured the coupling link and recoil spring level are properly seated together. For the Artillery Luger I've notice the same thing but also that when I attempt to lock the toggle back after reattaching the receiver to the frame, it gets hung up/stuck and will not go back to allow me to engage the locking bolt. I've tried following several YouTube videos and the official manual with no luck. An inspection of both shows no missing or damaged parts so I'm at a bit of a loss... Any help is appreciated! (I'll see about getting some pictures as well.) Last edited by LightWeaponsGuy; 08-24-2020 at 08:17 PM. Reason: note about photos |
08-24-2020, 08:41 PM | #2 |
User
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,696
Thanks: 792
Thanked 1,679 Times in 552 Posts
|
The first issue sounds like the "S" arm is overriding the main spring hook. Elevate the muzzle a bit, pull the receiver forward until the "S" arm clears the main spring hook. Then gently slide the receiver back and watch for the "S" arm to engage the hook. Replace the side plate, place the muzzle against a soft pad, push the top assembly rearward against the spring pressure and raise the locking block into place.
If the top assembly gets stuck to the rear, it's a good indication that the "S" arm is NOT engaging the main spring hook. If properly engaged, pushing or pulling the top assembly rearward will be against spring pressure. It is not necessary to retract the toggles in order to rotate the locking block into position. Simply push the muzzle against a soft surface to move everything rearward. For short barrels, I hook my fingers in the trigger guard and place the muzzle against my palm and squeeze. |
The following 6 members says Thank You to Doubs for your post: |
08-24-2020, 09:49 PM | #3 |
Super Moderator
Eternal Lifer LugerForum Patron Join Date: Jun 2002
Location: North of Spokane, WA
Posts: 15,931
Thanks: 2,030
Thanked 4,527 Times in 2,090 Posts
|
Is the Artillery dated 1914?
If it is - it is very uncommon |
08-25-2020, 10:40 AM | #4 | |
User
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
|
Quote:
|
|
08-25-2020, 10:44 AM | #5 |
User
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
|
|
08-25-2020, 05:44 PM | #6 |
User
Join Date: Feb 2018
Location: South Carolina
Posts: 847
Thanks: 782
Thanked 860 Times in 410 Posts
|
Pictures of the rig please! The 32 round drums were not issued until later in the war as I recall.
__________________
-QM Looking for Mauser S/42 toggle train #22 |
08-26-2020, 06:13 PM | #7 |
User
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
|
|
08-28-2020, 10:26 AM | #8 |
Super Moderator - Patron
LugerForum Life Patron Join Date: Dec 2009
Location: Eastern North Carolina, USA
Posts: 3,909
Thanks: 1,374
Thanked 3,110 Times in 1,510 Posts
|
Often, with correct positioning you can engage the "S" hook withe the recoil lever "hooks" properly in the toggle mechanism.
Sometimes, turning the Luger upside down will help you clear the area and position the parts for correct engagement when you turn it back over. Gravity is your friend.
__________________
Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war. |
The following 3 members says Thank You to mrerick for your post: |
09-02-2020, 02:54 PM | #9 | |
User
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
|
Quote:
|
|
The following member says Thank You to LightWeaponsGuy for your post: |
09-02-2020, 02:56 PM | #10 | |
User
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
|
Quote:
|
|
09-02-2020, 05:18 PM | #11 |
User
Join Date: Jun 2020
Posts: 99
Thanks: 244
Thanked 95 Times in 37 Posts
|
|
Tags |
1914 dwm, help need, issues, new luger, reassembly |
Thread Tools | |
Display Modes | |
|
|