LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > Luger Discussion Forums > All P-08 Military Lugers

Reply
 
Thread Tools Display Modes
Unread 08-24-2020, 08:17 PM   #1
LightWeaponsGuy
User
 
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
Default Issues with reassembly

Hello all,

I recently came into the possession of two 1914 DWM produced Lugers and require some input regarding reassembly. One Luger is a standard size while the other is an Artillery Luger. Both were stored in less than ideal conditions which prompted me to field strip and clean them. (Thankfully no major rust or no damage!)

However, I've run into issues during reassembly. On the standard Luger I've noticed that the slide is loose and slides back and forth after I reattach the receiver to the frame and lock the toggle (It does this when the locking bolt and takedown plate are in place, as well as not in place.) I've ensured the coupling link and recoil spring level are properly seated together.

For the Artillery Luger I've notice the same thing but also that when I attempt to lock the toggle back after reattaching the receiver to the frame, it gets hung up/stuck and will not go back to allow me to engage the locking bolt.

I've tried following several YouTube videos and the official manual with no luck. An inspection of both shows no missing or damaged parts so I'm at a bit of a loss... Any help is appreciated!

(I'll see about getting some pictures as well.)

Last edited by LightWeaponsGuy; 08-24-2020 at 08:17 PM. Reason: note about photos
LightWeaponsGuy is offline   Reply With Quote
Unread 08-24-2020, 08:41 PM   #2
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,696
Thanks: 792
Thanked 1,679 Times in 552 Posts
Default

The first issue sounds like the "S" arm is overriding the main spring hook. Elevate the muzzle a bit, pull the receiver forward until the "S" arm clears the main spring hook. Then gently slide the receiver back and watch for the "S" arm to engage the hook. Replace the side plate, place the muzzle against a soft pad, push the top assembly rearward against the spring pressure and raise the locking block into place.

If the top assembly gets stuck to the rear, it's a good indication that the "S" arm is NOT engaging the main spring hook. If properly engaged, pushing or pulling the top assembly rearward will be against spring pressure.

It is not necessary to retract the toggles in order to rotate the locking block into position. Simply push the muzzle against a soft surface to move everything rearward. For short barrels, I hook my fingers in the trigger guard and place the muzzle against my palm and squeeze.
Doubs is offline   Reply With Quote
The following 6 members says Thank You to Doubs for your post:
Unread 08-25-2020, 10:40 AM   #3
LightWeaponsGuy
User
 
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
Default

Quote:
Originally Posted by Doubs View Post
The first issue sounds like the "S" arm is overriding the main spring hook. Elevate the muzzle a bit, pull the receiver forward until the "S" arm clears the main spring hook. Then gently slide the receiver back and watch for the "S" arm to engage the hook. Replace the side plate, place the muzzle against a soft pad, push the top assembly rearward against the spring pressure and raise the locking block into place.

If the top assembly gets stuck to the rear, it's a good indication that the "S" arm is NOT engaging the main spring hook. If properly engaged, pushing or pulling the top assembly rearward will be against spring pressure.

It is not necessary to retract the toggles in order to rotate the locking block into position. Simply push the muzzle against a soft surface to move everything rearward. For short barrels, I hook my fingers in the trigger guard and place the muzzle against my palm and squeeze.
I'll definitely give this a shot! Keeping my fingers crossed it works
LightWeaponsGuy is offline   Reply With Quote
Unread 09-02-2020, 02:54 PM   #4
LightWeaponsGuy
User
 
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
Default

Quote:
Originally Posted by Doubs View Post
The first issue sounds like the "S" arm is overriding the main spring hook. Elevate the muzzle a bit, pull the receiver forward until the "S" arm clears the main spring hook. Then gently slide the receiver back and watch for the "S" arm to engage the hook. Replace the side plate, place the muzzle against a soft pad, push the top assembly rearward against the spring pressure and raise the locking block into place.

If the top assembly gets stuck to the rear, it's a good indication that the "S" arm is NOT engaging the main spring hook. If properly engaged, pushing or pulling the top assembly rearward will be against spring pressure.

It is not necessary to retract the toggles in order to rotate the locking block into position. Simply push the muzzle against a soft surface to move everything rearward. For short barrels, I hook my fingers in the trigger guard and place the muzzle against my palm and squeeze.
Your trick work perfectly! I'm glad to have them all back together again Now to hopefully get some good photos and post them here.
LightWeaponsGuy is offline   Reply With Quote
The following member says Thank You to LightWeaponsGuy for your post:
Unread 08-24-2020, 09:49 PM   #5
Edward Tinker
Super Moderator
Eternal Lifer
LugerForum
Patron
 
Edward Tinker's Avatar
 
Join Date: Jun 2002
Location: North of Spokane, WA
Posts: 15,929
Thanks: 2,029
Thanked 4,527 Times in 2,090 Posts
Default

Is the Artillery dated 1914?

If it is - it is very uncommon
Edward Tinker is offline   Reply With Quote
Unread 08-25-2020, 10:44 AM   #6
LightWeaponsGuy
User
 
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
Default

Quote:
Originally Posted by Edward Tinker View Post
Is the Artillery dated 1914?

If it is - it is very uncommon
Just double checked and it is indeed stamped '1914' on the barrel, serial #1373. Unfortunately I do not have the snail magazine for it but was able to find a stock/holster along with it too.
LightWeaponsGuy is offline   Reply With Quote
Unread 08-25-2020, 05:44 PM   #7
HerrKaiser
User
 
HerrKaiser's Avatar
 
Join Date: Feb 2018
Location: South Carolina
Posts: 845
Thanks: 782
Thanked 860 Times in 410 Posts
Default

Pictures of the rig please! The 32 round drums were not issued until later in the war as I recall.
__________________
-QM

Looking for Mauser S/42 toggle train #22
HerrKaiser is offline   Reply With Quote
Unread 08-26-2020, 06:13 PM   #8
LightWeaponsGuy
User
 
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
Default

Quote:
Originally Posted by HerrKaiser View Post
Pictures of the rig please! The 32 round drums were not issued until later in the war as I recall.
I'll definitely post some once I get them back together No drum with it sadly and don't have the spare cash to get one (even the $500 repo ones...)
LightWeaponsGuy is offline   Reply With Quote
Unread 08-28-2020, 10:26 AM   #9
mrerick
Super Moderator - Patron
LugerForum
Life Patron
 
mrerick's Avatar
 
Join Date: Dec 2009
Location: Eastern North Carolina, USA
Posts: 3,909
Thanks: 1,374
Thanked 3,110 Times in 1,510 Posts
Default

Often, with correct positioning you can engage the "S" hook withe the recoil lever "hooks" properly in the toggle mechanism.

Sometimes, turning the Luger upside down will help you clear the area and position the parts for correct engagement when you turn it back over. Gravity is your friend.
__________________
Igitur si vis pacem, para bellum -
- Therefore if you want peace, prepare for war.
mrerick is offline   Reply With Quote
The following 3 members says Thank You to mrerick for your post:
Unread 09-02-2020, 02:56 PM   #10
LightWeaponsGuy
User
 
Join Date: Aug 2020
Location: United States of America
Posts: 6
Thanks: 1
Thanked 1 Time in 1 Post
Default

Quote:
Originally Posted by mrerick View Post
Often, with correct positioning you can engage the "S" hook withe the recoil lever "hooks" properly in the toggle mechanism.

Sometimes, turning the Luger upside down will help you clear the area and position the parts for correct engagement when you turn it back over. Gravity is your friend.
I'm definitely slowly learn the reassembly gymnastics one has to do with the Luger Oddly though I find them easier to deal with in terms of cleaning and disassembly than most modern handguns.
LightWeaponsGuy is offline   Reply With Quote
Unread 09-02-2020, 05:18 PM   #11
Fla.Mallard
User
 
Fla.Mallard's Avatar
 
Join Date: Jun 2020
Posts: 99
Thanks: 244
Thanked 95 Times in 37 Posts
Default

Quote:
Originally Posted by LightWeaponsGuy View Post
Oddly though I find them easier to deal with in terms of cleaning and disassembly than most modern handguns.
They aren't as easy as a Glock or Sig but after watching one video, I found that I can strip and re-assemble a Luger with little or no difficulty.
Fla.Mallard is offline   Reply With Quote
Reply

Tags
1914 dwm, help need, issues, new luger, reassembly

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:30 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Lugerforum.com