![]() |
my profile |
register |
faq |
search upload photo | donate | calendar |
![]() |
#1 |
New User
Join Date: Jul 2018
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]()
Which brand carries the correct bullets for my P08? The ones I am buying (in a variety of grain weights) seem to have a slightly tapered case so that as I load more and more bullets in the clip the angle becomes flatter so that by the time I have 4 shells in, the angle of the bullet in the clip is so flat that the front of the bullet is touching the magazine itself and won't push out. I have two clips -- they both exhibit the same problem.
And looking at the shells through the side slit it is clear that the first to be laded still have a steep angle -- each shell has a flatter angle than the previous one. A friend's home-loads do not exhibit this problem - and it is evidently the fault of the brands I am purchasing. Any advice highly appreciated. Last edited by Edward Tinker; 07-30-2018 at 10:12 PM. |
![]() |
![]() |
![]() |
#2 |
User
Join Date: Mar 2018
Location: Newnan, GA
Posts: 141
Thanks: 280
Thanked 48 Times in 30 Posts
|
![]()
All 9mm Luger cases have a slight taper from base to front. Use Winchester white box 115 gr standard load. Sounds like there is an issue with the magazines or followers. Good luck, Mike
|
![]() |
![]() |
![]() |
#3 |
Patron
LugerForum Patron Join Date: Nov 2008
Posts: 4,047
Thanks: 578
Thanked 1,414 Times in 887 Posts
|
![]()
115 gr. FMJ should not exceed the maximum length. As Mike said, Winchester white box is a good go-to. If those are too long there is no doubt some magazine problem and further discussion and photos will be required.
dju |
![]() |
![]() |
![]() |
#4 |
Moderator
Lifetime Forum Patron Join Date: Jun 2002
Location: Arizona/Colorado
Posts: 7,763
Thanks: 4,865
Thanked 3,105 Times in 1,429 Posts
|
![]()
"bullets" themselves hang out into space compared to the shell casings they rest in. The bullets should have NO affect on the angle of an inserted cartridge..Unless the LENGTH is causing them to rub the front face of the magazine. If this is the case, the bullet will cause lift and separation of the cartridge cases. Get a dial caliper and measure the length of your cartridges.
__________________
Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 lugerholsterrepair@earthlink.net 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) ![]() "For those who Fight For It, Life has a flavor the protected will never know." |
![]() |
![]() |
The following 3 members says Thank You to lugerholsterrepair for your post: |
![]() |
#5 |
User
Join Date: Jul 2003
Location: New York, NY
Posts: 1,575
Thanks: 2,124
Thanked 400 Times in 249 Posts
|
![]()
Hi:
Proper O.A.L. of the specific cartridge is vital to proper Luger function. With a round nose bullet, 1.173 is what DWM called for. You "might" get away with the standard SAAMI maximum of 1.169, maybe. Yes, the Luger, with its highly slanted grip, was designed to "slide" its cartridges up the magazine at a very steep angle. To fully understand why, in the Shooting Reloading section, please read my Sticky titled "Determining Proper Cartridge O.A.L.. If you are a reloader, this would make your Luger shooting much easier for you. I hope this helps. Sieger |
![]() |
![]() |
![]() |
#6 |
Super Moderator
Eternal Lifer LugerForum Patron Join Date: Jun 2002
Location: North of Spokane, WA
Posts: 15,916
Thanks: 1,992
Thanked 4,506 Times in 2,080 Posts
|
![]()
I added a subscription for this so you'll get notified.
Just in case - If you are asking what cartridges work well for it - I have found that standard 115 grain, such as Winchester White box works well. Although I personally have found that most factory full metal jacket (FMJ) works fine, although some lugers are just finicky.
__________________
Edward Tinker ************ Co-Author of Police Lugers - Co-Author of Simson Lugers Author of Veteran Bring Backs Vol I, Vol II, Vol III and Vol IV |
![]() |
![]() |
![]() |
#7 |
User
Join Date: Apr 2016
Location: Newburgh,IN
Posts: 768
Thanks: 372
Thanked 603 Times in 320 Posts
|
![]()
I know far less than most of the folks that are regulars on this forum. But, like Ed above commented, I have found with my two shooter grade Lugers that most off the shelf 115gn FMJ ammo feeds and functions well.
However, I tend to choose WWB 115gn FMJ, if for no other reason than it is the choice of the majority of Lugermeisters here. ![]()
__________________
“God created war so that Americans would learn geography.” ― Mark Twain |
![]() |
![]() |
![]() |
#8 |
Lifer
Lifetime Forum Patron Join Date: Dec 2003
Location: PORT ST LUCIE, FLORIDA
Posts: 12,216
Thanks: 6,209
Thanked 4,133 Times in 2,173 Posts
|
![]()
Walmart sells the white Winchester luger bullets here in Florida~
|
![]() |
![]() |
![]() |
#9 |
Super Moderator - Patron
LugerForum Life Patron Join Date: Dec 2009
Location: Eastern North Carolina, USA
Posts: 3,900
Thanks: 1,372
Thanked 3,094 Times in 1,503 Posts
|
![]()
Hi Rudy, and welcome to the forum.
It isn't clear what country you live in. If you're in a country like Italy that prohibits 9mm Luger ammunition to civilians, you may be dealing with another caliber like 9x23mm. If you're in the USA, stick with what they recommended above. Other places, look for standard velocity 9mm Luger (Parabellum) ammunition. Most of us don't try and fully load Luger magazines. Perhaps 5 cartridges maximum. Yes - they are designed for more, but it's often not wise to stress things in older components. As Sieger mentioned, the ammunition overal cartridge length is important for proper Luger cycling. SAAMI has exact specifications that are modern, and generally describe ammunition that should conform and work properly. Remember that Lugers were hand fitted by the factory. If things have been changed out and refit by someone with less familiarity with the Luger mechanism, all bets are off.
__________________
- Therefore if you want peace, prepare for war. |
![]() |
![]() |
![]() |
#10 |
User
Join Date: Aug 2008
Location: Virginia
Posts: 197
Thanks: 26
Thanked 315 Times in 112 Posts
|
![]()
As other have said, Winchester White box FMJ have worked well for me, although I use a lot of PMC 9mm in my Lugers and modern 9mm handguns. I generally use MecGar mags with the Lugers, 100 year old DWM mags have 100 year old springs and may need a trip to GT to correct issues with the tube and/or feed lips. I always use 115 grain FMJ, regardless of brand.
__________________
- Mike Life member: NRA, OVMS, VGCA Member: NAPCA, N-SSA(Veteran) Si vis pacem, para bellum |
![]() |
![]() |
![]() |
#11 | |
User
Join Date: Sep 2007
Posts: 1,225
Thanks: 2,679
Thanked 929 Times in 509 Posts
|
![]() Quote:
But 9x21 OAL is the same as the 9 para. |
|
![]() |
![]() |
![]() |
|
|