LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Shooting and Reloading

Reply
Thread Tools Display Modes
Unread 12-23-2020, 02:03 PM   #1
JONABI
User
 
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
Default Gauging a dial caliper for reloading (9mm)

I know a lot of you guys reload for the magnificent Luger. Can you give me a hint how to gauge a caliper so that I'll be certain for any measure that I make. My caliper is swiss made, 5" brand new from 30 yars ago. It has a vernier in mm and 10 th of a mm also the vernier has provision for the measure inches and tenthof inches coupled with a dial covering a hundred and thoudand of an inch. I tried to find a simple gauge block but instead they could only sale me a complete set at 1900.00$. Too much for me. Any idear ? Thanks!
JONABI is offline   Reply With Quote
Unread 12-23-2020, 02:19 PM   #2
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,662
Thanks: 762
Thanked 1,586 Times in 517 Posts
Default

If you close your caliper and zero the dial, you should be good to go.

Even if you use cases with the same headstamp and bullets from the same lot, there will be minor differences in your loads because there are differences in the components. Not all cases will be identical in length and not all bullets will have the same nose to ogive distance. The differences will be a few thousands of an inch but they will be there. You'll find the same differences in factory loaded cartridges.
Doubs is offline   Reply With Quote
The following member says Thank You to Doubs for your post:
Unread 12-23-2020, 02:41 PM   #3
DonVoigt
User
 
DonVoigt's Avatar
 
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,674
Thanks: 1,435
Thanked 4,341 Times in 2,036 Posts
Default

You can buy a 1" precision standard for less than $20 if you want.
Search ebay or amazon.
I bought mine from Amazon, it's made by Mitutoyo/Japan.

But like Doubs said, if it "zeros" when closed- you are good to go for most work!
__________________
03man(Don Voigt); Luger student and collector.
Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie
DonVoigt is offline   Reply With Quote
The following 2 members says Thank You to DonVoigt for your post:
Unread 12-23-2020, 04:11 PM   #4
JONABI
User
 
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
Default

Thank you for the answer. Well I understand your arguments. But, since I'm only starting the reloading process I think it's good idear to start square.
JONABI is offline   Reply With Quote
Unread 12-23-2020, 04:43 PM   #5
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,662
Thanks: 762
Thanked 1,586 Times in 517 Posts
Default

Quote:
Originally Posted by JONABI View Post
Thank you for the answer. Well I understand your arguments. But, since I'm only starting the reloading process I think it's good idea to start square.
Forgive me for being a bit confused but I don't understand what you're trying to say. A normal dial caliper as sold by places such as Midway, Graf's etc. will be accurate enough for your reloading needs.

I shoot competition centerfire rifle benchrest and few people in this world are more anal about precision than benchrest shooters.

If you reload to an overall length, you'll discover that the difference in your cartridges will be + or - more than you might think. That's due to a number of factors. I load my cartridges for an ogive-to-lands setting that is zero + or - .001". I turn the outside neck to a consistent thickness and load for .005" neck tension. Case length is trimmed, flash holes reamed to remove flashing and primer pockets uniformed. Others take it much farther than I do.

Reloading 9mm or .30 Luger does NOT require that level of precision... especially if you're shooting them in a Luger. Between manufacturers, cases can have thicker or thinner walls and vary in length. Bullets of the same weight and general design from different makers will have different ogive lengths.

I don't want to make it seem that reloading 9mm is difficult because it isn't but if you expect to keep all your measurements within .001", you won't. There are simply too many variables.
Doubs is offline   Reply With Quote
The following 3 members says Thank You to Doubs for your post:
Unread 12-23-2020, 05:43 PM   #6
JONABI
User
 
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
Default Comparing measures in 2 units-caliper

I've lost my first reply( took too long, I was logged out).
Now I've zeroed my caliper: good. Measured a 9mm cartridge first reading mm=29,15 converted in inches= 1.1476 rounded to 1.148 compared to vernier combined with dial measurment= 1.145. Difference of at least .003 inche. That's why I want to calibrate my caliper because I won't be sure of any measurment until I can gauge it. I understand that I will face many variables while reloading. But at least I should know for sure what's the real reading before I start reloading to expect some kind of accuracy.
Attached Thumbnails
Click image for larger version

Name:	IMG_1451.jpg
Views:	69
Size:	136.2 KB
ID:	81532  

Click image for larger version

Name:	IMG_1452.jpg
Views:	78
Size:	138.1 KB
ID:	81533  


Last edited by JONABI; 12-23-2020 at 05:48 PM. Reason: Pictures didn't load
JONABI is offline   Reply With Quote
Unread 12-23-2020, 05:53 PM   #7
JONABI
User
 
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
Default Gauge block

Thanks! I'll find a gauge block somewhere else than Amazon or Ebay. I prefer to be local when it's possible. Thank you anyway!.

Last edited by JONABI; 12-23-2020 at 05:54 PM. Reason: correction
JONABI is offline   Reply With Quote
Unread 12-23-2020, 06:11 PM   #8
lugerholsterrepair
Moderator
Lifetime Forum
Patron
 
lugerholsterrepair's Avatar
 
Join Date: Jun 2002
Location: Arizona/Colorado
Posts: 7,756
Thanks: 4,821
Thanked 3,087 Times in 1,423 Posts
Default

Your Einsteining the thing and making problems for yourself. Like a pilot on instruments..BELIEVE the gauges.
__________________
Jerry Burney
11491 S. Guadalupe Drive

Yuma AZ 85367-6182


lugerholsterrepair@earthlink.net

928 342-7583 (CO & AZ) Year Round
719 207-3331 (cell)


"For those who Fight For It, Life has a flavor the protected will never know."
lugerholsterrepair is offline   Reply With Quote
The following 2 members says Thank You to lugerholsterrepair for your post:
Unread 12-23-2020, 06:21 PM   #9
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,662
Thanks: 762
Thanked 1,586 Times in 517 Posts
Default

WHY are you converting anything? Your calipers read directly in inches and thousands of an inch.

The bottom picture shows your 9mm cartridge COL measurement to be exactly 1.045"

Jerry is exactly right; you're over complicating things.
Doubs is offline   Reply With Quote
The following 3 members says Thank You to Doubs for your post:
Unread 12-23-2020, 06:28 PM   #10
gunbugs
Lifetime Forum
Patron
 
gunbugs's Avatar
 
Join Date: Sep 2013
Location: Fairbanks, Alaska. Home of the best moose.
Posts: 626
Thanks: 332
Thanked 1,106 Times in 370 Posts
Default

I'd ditch the plastic caliper, and get a Mitutoyo, or Starrett caliper. They aren't that expensive, and are much better tools. That's just me, though.
gunbugs is offline   Reply With Quote
The following 3 members says Thank You to gunbugs for your post:
Unread 12-23-2020, 07:59 PM   #11
mrerick
Super Moderator - Patron
LugerForum
Life Patron
 
mrerick's Avatar
 
Join Date: Dec 2009
Location: Eastern North Carolina, USA
Posts: 3,900
Thanks: 1,370
Thanked 3,094 Times in 1,503 Posts
Default

The easy way to make and gauge 9mm Luger is to use a calibrated chamber case gauge like one of these:

https://www.midwayusa.com/product/1018249683?pid=793368

These cartridge gauges are inexpensive, and will save you more in time as you reload than any other method.

They come from a number of companies.

I 100% inspect my reloaded ammo with these gauges. Drop in the cartridge, Let it fall out and put the finished gauged cartridge in the box.

https://www.youtube.com/watch?v=hIraXq6u0VY
__________________
Igitur si vis pacem, para bellum -
- Therefore if you want peace, prepare for war.
mrerick is offline   Reply With Quote
Unread 12-23-2020, 10:13 PM   #12
lugerholsterrepair
Moderator
Lifetime Forum
Patron
 
lugerholsterrepair's Avatar
 
Join Date: Jun 2002
Location: Arizona/Colorado
Posts: 7,756
Thanks: 4,821
Thanked 3,087 Times in 1,423 Posts
Default

Here's the one I use. https://www.ebay.com/itm/Lyman-Ammo-...72.m2749.l2649
__________________
Jerry Burney
11491 S. Guadalupe Drive

Yuma AZ 85367-6182


lugerholsterrepair@earthlink.net

928 342-7583 (CO & AZ) Year Round
719 207-3331 (cell)


"For those who Fight For It, Life has a flavor the protected will never know."
lugerholsterrepair is offline   Reply With Quote
Unread 12-24-2020, 02:40 AM   #13
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,662
Thanks: 762
Thanked 1,586 Times in 517 Posts
Default

As I've explained in another thread, my loads for my 9mm Lugers are fine... in my Lugers. OTOH, my newer 9mm handguns have different chambers and will jam with the Luger loads. The bullets engage the lands too early and the bullets must be seated deeper. The same problem exists with .30 Luger loads for my Lugers and my newer .30 Luger pistols... a Benelli B80 and a Browning High Power.
Doubs is offline   Reply With Quote
The following 2 members says Thank You to Doubs for your post:
Unread 12-24-2020, 09:50 AM   #14
Kiwi
User
 
Kiwi's Avatar
 
Join Date: Mar 2019
Location: Wrong side of the Delaware river
Posts: 279
Thanks: 184
Thanked 394 Times in 154 Posts
Default

What are you measuring? girth or OAL
For Girth the measuring blocks are faster and error free, you can't make a mistake

For OAL I use a micrometer a 1-2" covers almost all pistol cartridges (.380 is under 1")
E-Bay has (1,837 results for micrometer 1-2) mostly $20 -$30 but with a few about $10

I do have Vernier calipers but no dial and no plastic. I find the micrometer much easier to use for measurement, but then just set a caliper to that measured length and lock the caliper.

I have several Vernier's as I pick them up at Garage sales for $1
Kiwi is offline   Reply With Quote
Unread 12-24-2020, 10:21 AM   #15
calibrator
User
 
calibrator's Avatar
 
Join Date: Feb 2009
Location: Cave Creek
Posts: 315
Thanks: 55
Thanked 242 Times in 92 Posts
Default

As a Machinist, I use dial calipers a LOT. I also reload and have a "Lyman" stainless steel caliper just for that. Calipers are perfect for reloading issues. I certainly DON'T use them for grinding a crankshaft or honing a cylinder bore when accurate readings to .0001" (a tenth of a thousandth) are required.

Of the dozens of dial calipers I've used (and it doesn't matter if Starrett or something Chinese), I often re-check my zero, as it seems as they wear, the needle will loose it's press fit on the pinion shaft and move slightly when the caliper is opened and closed quickly. In a low stress environment like reloading slowly opening and closing the jaws is more doable .

I also like using the case gages for checking re-loads before boxing them, however, they only check case sizing NOT COAL. Recently came across these my employer got in a box of supplies he bought from an estate;

https://www.topbrass-inc.com/collect...12832996851765

You get instant feedback regarding min/max SAMMI Specs for a caliber.
calibrator is offline   Reply With Quote
Unread 12-24-2020, 10:36 AM   #16
calibrator
User
 
calibrator's Avatar
 
Join Date: Feb 2009
Location: Cave Creek
Posts: 315
Thanks: 55
Thanked 242 Times in 92 Posts
Default

Maybe I complicate things here for you by adding this. I don't re-load for pistol, just precision high power centerfire rifle. Knowing how far the bullet "jumps" into the rifling is critical for load development. If the rifle is magazine fed, what will just fit into the mag is usually the limit unless rds are single loaded by hand.

I use this gage by Hornady to determine this dimension;

https://www.bing.com/videos/search?q...3&&FORM=VDRVRV
calibrator is offline   Reply With Quote
The following member says Thank You to calibrator for your post:
Unread 12-24-2020, 01:29 PM   #17
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,662
Thanks: 762
Thanked 1,586 Times in 517 Posts
Default

Quote:
Originally Posted by calibrator View Post
Maybe I complicate things here for you by adding this. I don't re-load for pistol, just precision high power centerfire rifle. Knowing how far the bullet "jumps" into the rifling is critical for load development. If the rifle is magazine fed, what will just fit into the mag is usually the limit unless rds are single loaded by hand.

I use this gage by Hornady to determine this dimension;

https://www.bing.com/videos/search?q...3&&FORM=VDRVRV
I have the same Hornady set but with the anvil in addition to the items you show. For Christmas my sons gave me the new Forster set that I like for measuring cases and ogive-to-lands.

https://www.midsouthshooterssupply.c...in-storage-box
Doubs is offline   Reply With Quote
Unread 12-24-2020, 05:36 PM   #18
rhuff
Patron
LugerForum
Patron
 
rhuff's Avatar
 
Join Date: Mar 2011
Location: Az.
Posts: 2,269
Thanks: 2,678
Thanked 956 Times in 702 Posts
Default

For my handloading I keep both a set of digital calipers and dial calipers handy on my bench. Either will get the job done. I don't own a plastic caliper, and likely will never purchase one. Maybe I am just too "old school"!!
__________________
Need DWM breechblock #21
rhuff is offline   Reply With Quote
Unread 12-24-2020, 10:22 PM   #19
JONABI
User
 
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
Default

Thank you for the suggestion and link.
JONABI is offline   Reply With Quote
Unread 12-24-2020, 10:25 PM   #20
JONABI
User
 
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
Default

Thanks for the link!
JONABI is offline   Reply With Quote
Reply

Tags
preps to start reloading

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:35 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Lugerforum.com