LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Repairs, Restoration & Refinishing

Closed Thread
Thread Tools Display Modes
Unread 04-17-2015, 06:17 PM   #1
G.T.
Lifer
Lifetime Forum
Patron
 
Join Date: Jun 2002
Location: Chandler Arizona
Posts: 3,483
Thanks: 1,282
Thanked 3,579 Times in 988 Posts
Default mainspring identification?

Hello to all, I have been diligently repairing Luger magazines and sometimes lugers over the last few years, and I'm getting to where I've seen quite a bit of weird stuff? Handmade, homemade, shade tree gunsmith kinda stuff? I have learned that the three most important aspects for good function are, correct mainspring, new or excellent extractor spring, and proper magazine spring, in a good to excellent magazine. Well, the question I have here, is about mainsprings.. I remember seeing, in either an early book by Datig, or Smith, a small chart where he list some of the more common spring dimensions... As I no longer have the books, I was wondering if someone in the membership could look for me? The spring I have has 17 coils, is approx. 2.900" long, and has a wire dia. of .057" Let me know if anyone has any idea as to it's origin??... Best to all, til...latr....GT...
G.T. is offline  
The following member says Thank You to G.T. for your post:
Unread 04-17-2015, 06:58 PM   #2
mrerick
Super Moderator - Patron
LugerForum
Life Patron
 
mrerick's Avatar
 
Join Date: Dec 2009
Location: Eastern North Carolina, USA
Posts: 3,900
Thanks: 1,370
Thanked 3,094 Times in 1,503 Posts
Default

Wolff springs has three weights of recoil spring:

http://www.gunsprings.com/index.cfm?...s&cID=1&mID=38

I believe that the one you have is the 36lb spring.

IIRC, these would be appropriate for 7.65mm Luger pistols and early 9mm guns.

Sturgess, on page 905, discusses spring versions. He says early P.04 and P.08 guns had 18 turns of 1.5mm wire. 1916-1917 dated pistols had a new standard P.08 mainspring 22 turns of 1.4mm wire. There were also changes to the mainspring well.

On page 1093 there is extensive discussion.

The LP08 started out prototyped with 22 turns of 1.4mm wire, was produced in 1914 with 18 turns of 1.4mm wire, and then in 1916 with 22 turns of 1.4mm wire.

The P08 in 1913 had 18 turns of 1.5mm wire and then in 1915 had 22 turns of 1,4mm wire. The frame wells were shaped differently near the bottom of the grips.

The changes relate mainly to the mass of the receiver and the power of the cartridge. It all relates to the balance of the action's operation.

On page 1061 he lists specifications:

3.2 Recoil Spring
Luger 1899 (double) Spring steel, spring hard, finished as sample (Old Model)
DWM 1904 19 turns. Load at a length of 50 mm: 7 to 8 kg. Load at a length of 34 mm: 15 to 16.5 kg.
I.K.B. 1913 Cast crucible steel wire, spring hard, or naturally hard crucible steel wire. 22 turns, both ends bent even.
Mauser 1934 Cast steel spring wire “Extra-Extra”, carbon content 0.8 %. Anneal to yellow colour.
Mauser 1942 Spring steel, carbon content 0.8 %. Anneal to yellow colour.
__________________
Igitur si vis pacem, para bellum -
- Therefore if you want peace, prepare for war.
mrerick is offline  
The following member says Thank You to mrerick for your post:
Unread 04-17-2015, 07:10 PM   #3
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,181
Thanks: 1,394
Thanked 4,438 Times in 2,327 Posts
Default

Somebody else usually posts exactly the same thing right after I do, so when they do, I'll delete this...
Attached Thumbnails
Click image for larger version

Name:	mainsprings.jpg
Views:	97
Size:	98.6 KB
ID:	48101  

__________________
I like my coffee the
way I like my women...
...Cold and bitter...
sheepherder is offline  
The following 10 members says Thank You to sheepherder for your post:
Unread 04-17-2015, 08:25 PM   #4
G.T.
Lifer
Lifetime Forum
Patron
 
Join Date: Jun 2002
Location: Chandler Arizona
Posts: 3,483
Thanks: 1,282
Thanked 3,579 Times in 988 Posts
Default That's it!

Closest is the 08 one? funny thing is, the 08 was issued without a hold open... they added them later... The particular frame this spring came out of is a Mauser 1938, but obviously not original to the gun.... But, it had issues with inconsistent hold open on the last round.. Put a WW2 Mauser mainspring in it, and boom! 100% hold open function........ I wonder if a mainspring change wasn't performed along with the hold open added operation?... Best to all, til...lat'r...GT ...... Thanks Rich!
G.T. is offline  
The following member says Thank You to G.T. for your post:
Unread 04-17-2015, 10:18 PM   #5
Edward Tinker
Super Moderator
Eternal Lifer
LugerForum
Patron
 
Edward Tinker's Avatar
 
Join Date: Jun 2002
Location: North of Spokane, WA
Posts: 15,902
Thanks: 1,981
Thanked 4,487 Times in 2,071 Posts
Default

whew, closed the thread before Rich could delete his stuff
Edward Tinker is offline  
The following 2 members says Thank You to Edward Tinker for your post:
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:29 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Lugerforum.com