![]() |
my profile |
register |
faq |
search upload photo | donate | calendar |
![]() |
#1 |
New User
Join Date: Jul 2023
Posts: 2
Thanks: 0
Thanked 2 Times in 1 Post
|
![]()
I recently inherited a Luger and would appreciate any help in identifying it. Attached are photos of the markings I could find.
|
![]() |
![]() |
The following 2 members says Thank You to bloungo for your post: |
![]() |
#2 |
Lifer
Lifetime Forum Patron Join Date: Apr 2015
Location: Austin, Texas
Posts: 698
Thanks: 2,062
Thanked 573 Times in 307 Posts
|
![]()
Welcome to the Forum.
Thanks for sharing your luger What have you found out about it, so far? Was there a story about where it came from? |
![]() |
![]() |
![]() |
#3 |
Patron
LugerForum Patron Join Date: Mar 2011
Location: Az.
Posts: 2,282
Thanks: 2,702
Thanked 969 Times in 714 Posts
|
![]()
It is obviously a "parts" Luger....made up of different parts from different Lugers. I believe that parts of it have been refinished. It should make a good shooter, but not a collector piece. Congrats!!
__________________
Need DWM breechblock #21 |
![]() |
![]() |
![]() |
#4 |
New User
Join Date: Jul 2023
Posts: 2
Thanks: 0
Thanked 2 Times in 1 Post
|
![]()
What makes it a parts Luger? All the numbers seem to match.
|
![]() |
![]() |
![]() |
#5 |
User
Join Date: Feb 2023
Posts: 132
Thanks: 81
Thanked 149 Times in 63 Posts
|
![]()
All of the parts should have 44 on them not 59...the last two digits of the Serial number on the frame. The toggle assembly does not match the frame number. It is a parts pistol.
Given that it is mismatched and seriously pitted and re blued it is on the bottom end of the shooter class.... not an heirloom. If you attempted to sell it, well, no idea but it would go on the cheap side. |
![]() |
![]() |
![]() |
#6 |
Lifer - Twice Over
Lifetime Forum Patron Join Date: Jun 2002
Location: Savannah
Posts: 517
Thanks: 0
Thanked 255 Times in 113 Posts
|
![]()
Bloungo,
It appears from your photographs that the retaining pin for the rear toggle pin is missing. I suggest that you check this and rectify any problem before attempting to fire the gun. Karl |
![]() |
![]() |
The following 2 members says Thank You to Karl for your post: |
![]() |
#7 |
User
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,692
Thanks: 789
Thanked 1,670 Times in 548 Posts
|
![]()
It's a military Luger that has been refinished using parts from different pistols. The notch at the front of the receiver shows that the receiver was on either a DWM Artillery Luger or a 1914 Erfurt Artillery Luger or a 1916 ~ 1918 Erfurt short barrel Luger. The date and proof/inspection stamps have been scrubbed so there's no way to tell.
The toggle train - or parts of it - are Erfurt while the frame is DWM. Your Luger falls into the shooter grade category. It has no collector value but if you inherited it, the sentimental value may outweigh all other considerations... as it should. |
![]() |
![]() |
The following 2 members says Thank You to Doubs for your post: |
![]() |
|
|