my profile |
register |
faq |
search upload photo | donate | calendar |
03-08-2004, 08:36 PM | #1 |
Moderator
2010 LugerForum Patron Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,019
Thanks: 1,090
Thanked 5,173 Times in 1,701 Posts
|
Early Frame Tutorial
Most of our Luger Forum members are familiar with the designation of"Long Frame" and "Short Frame". The "long" frame and receiver is 2mm longer than the "short" frame and receiver, with the extra length occurring in front of the takedown lever. The threaded portion of the long and short frame barrels are also 2mm different in length and therefore are not interchangeable.
However, some beginning Luger fans may not be aware that during early Luger development there were several transition steps from the old model "long" frame to the new model "short" frame. Here are Type categorizations of these transition steps that I have made into a little guide. These are my observations and I am sure this list may not be totally comprehensive and that exceptions do exist (all bets are off on 1920 era Lugers), but it is by and large representative. I welcome any recommended corrections, changes or comments. Type I - Old model long frame, thick rounded frame and trigger guard the full width of the frame. Type I is found on 1900 military and commercial Lugers, 1900 and 1902 Carbines, some 1902 Prototypes, and the 1904 Navy (with the addition of a stock lug). Type II - Old model short frame, squared off frame, trigger guard the full width of the frame, and "thin" frame below the takedown lever. Type II is found on 1902 commercial, American Eagle, and test Lugers (Dutch, German, and American Eagle), some 1902 Prototypes, and 1903 Commercial. Type III - New model long frame, rounded frame with rebated trigger guard (trigger guard machined narrower than the frame). Type III is found on 1906 Navy, early 1906 commercial and American Eagle (some safety marked and some with stock lug), 1906 Swiss (DWM Cross in Sunburst, DWM Cross in Shield and Waffenfabrik Bern produced). Type IV - New model short frame, squared off thin frame, rebated trigger guard. Type IV is found on early 1906 9mm Lugers (Commercial, American Eagle, Russian) and the 1907 .45 Caliber Test Luger. Also found on 1906 7.65mm Lugers such as: 1906 Bulgarian, M2 Portuguese, some Commercial, and some Swiss. Type V - New model short frame, squared off thick frame (with the thicker area below the takedown lever), rebated trigger guard. Type V is found on virtually all Lugers produced after 1908, to include commercial and contract Lugers of the 1906 pattern with grip safety.
__________________
If it's made after 1918...it's a reproduction Last edited by Ron Wood; 06-15-2020 at 04:27 PM. |
The following 25 members says Thank You to Ron Wood for your post: |
03-09-2004, 12:05 AM | #2 |
User
Join Date: Jun 2002
Location: Portland, Oregon
Posts: 3,900
Thanks: 0
Thanked 1,312 Times in 430 Posts
|
Ron,
Thanks for the really excellent and informative tutorial. I have a couple of questions. What frame details would one find on a 1904 Navy? In Type II, to what 1902 American Eagle Test Lugers do you refer? --Dwight |
03-09-2004, 03:29 AM | #3 |
Moderator
2010 LugerForum Patron Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,019
Thanks: 1,090
Thanked 5,173 Times in 1,701 Posts
|
Dwight,
The 1904 Navy frame is the old model flat laminated mainspring type "long" frame BUT with the addition of a stock lug. I will add the 1904 Navy to the Type I examples. Thank you. The 1902 US Test Cartridge Counter Lugers had the American Eagle over the chamber.
__________________
If it's made after 1918...it's a reproduction |
The following 3 members says Thank You to Ron Wood for your post: |
11-28-2010, 05:54 PM | #4 |
Super Moderator - Patron
LugerForum Life Patron Join Date: Dec 2009
Location: Eastern North Carolina, USA
Posts: 3,909
Thanks: 1,374
Thanked 3,110 Times in 1,510 Posts
|
PDF of Ron's Excellent Tutorial
I've attached a PDF format file of Ron's excellent tutorial:
__________________
Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war. |
The following 9 members says Thank You to mrerick for your post: |
11-28-2010, 07:31 PM | #5 |
Patron
LugerForum Patron Join Date: Mar 2009
Location: Colorado
Posts: 978
Thanks: 68
Thanked 127 Times in 108 Posts
|
Thank you, Marc!
FN |
11-29-2010, 02:31 AM | #6 |
User
Join Date: Oct 2007
Location: Maryland
Posts: 353
Thanks: 44
Thanked 119 Times in 58 Posts
|
Thanks Ron. WOW!! on the picture quality!!
|
The following member says Thank You to Wilhelm for your post: |
11-29-2010, 04:45 PM | #7 |
Guest
Posts: n/a
|
Very nice. Thanks.
|
11-29-2010, 06:36 PM | #8 |
Lifer
Lifetime Forum Patron Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,182
Thanks: 1,400
Thanked 4,442 Times in 2,330 Posts
|
+ 1
Right click; Save...
__________________
I like my coffee the way I like my women... ...Cold and bitter... |
The following 2 members says Thank You to sheepherder for your post: |
11-30-2010, 12:48 PM | #9 |
Moderator
2010 LugerForum Patron Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,019
Thanks: 1,090
Thanked 5,173 Times in 1,701 Posts
|
Hard to believe it has been six years already since that tutorial was first posted. Since then it has been published in Jan Still's last book and now is having a relook on this forum. Kind of like a bad penny...it keeps turning up!
__________________
If it's made after 1918...it's a reproduction |
11-30-2010, 12:52 PM | #10 |
Super Moderator
Eternal Lifer LugerForum Patron Join Date: Jun 2002
Location: North of Spokane, WA
Posts: 15,929
Thanks: 2,029
Thanked 4,527 Times in 2,090 Posts
|
A very nice penny Ron
Sometimes an effort that seemed easy for you, helps so many others. Well done. |
The following member says Thank You to Edward Tinker for your post: |
11-30-2010, 01:01 PM | #11 |
Moderator
2010 LugerForum Patron Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,019
Thanks: 1,090
Thanked 5,173 Times in 1,701 Posts
|
Stuff like this gets buried in the “Research Archives” section because only the last posting is directly accessible. The topics of “Early Lugers (1900-1906)”, “Military Lugers “, and “Commercial Lugers” have some neat information but you have to click on the main topic and then select “From the beginning” and “Show Threads” so see everything that is hidden there. New folks (and probably a bunch of regulars) are unaware of what is available.
__________________
If it's made after 1918...it's a reproduction |
The following member says Thank You to Ron Wood for your post: |
11-30-2010, 02:23 PM | #12 |
User
Join Date: Dec 2002
Location: Malta
Posts: 570
Thanks: 74
Thanked 12 Times in 12 Posts
|
As matter of fact I had to ask about the frame variations because I forgot about your tutorial, then I was directed to it.
Alf.
__________________
I prefer a Luger |
06-15-2020, 03:36 PM | #13 |
User
Join Date: Apr 2020
Location: The Mountains of Western North Carolina
Posts: 38
Thanks: 563
Thanked 33 Times in 21 Posts
|
Although I'm getting to this post somewhat after-the-fact, it's the kind of thing I'm eating up right now, as I dig deeper and learn more about my favorite firearm. Thanks, Ron, for all of the great information you've put up on the forum to help new members like me.
__________________
Cursum Perficio |
06-15-2020, 10:59 PM | #14 |
User
Join Date: Jan 2019
Location: Pa.
Posts: 157
Thanks: 535
Thanked 338 Times in 90 Posts
|
Never Old Info
Thanks Ron valuable information for those who crave details.
|
06-16-2020, 10:40 AM | #15 |
User
Join Date: Jan 2019
Location: Pa.
Posts: 157
Thanks: 535
Thanked 338 Times in 90 Posts
|
21 or 19
Ron is that 2mm difference directly related to the difference of the 7.65x21 and the 9x19 bullet lengths.?
|
06-16-2020, 12:52 PM | #16 |
Moderator
2010 LugerForum Patron Join Date: Jun 2002
Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso
Posts: 7,019
Thanks: 1,090
Thanked 5,173 Times in 1,701 Posts
|
I rather doubt it, there are examples of both frame types in either caliber. Almost certainly going to the short frame was an effort to reduce weight (and possibly a little aesthetics). I think the Swiss stayed with the long frame just because they didn't feel the necessity to re-tool.
Ron
__________________
If it's made after 1918...it's a reproduction |
The following 5 members says Thank You to Ron Wood for your post: |
05-14-2022, 06:21 PM | #17 |
Lifer
Lifetime Forum Patron Join Date: Sep 2020
Location: Winnipeg, Canada
Posts: 617
Thanks: 3,065
Thanked 1,057 Times in 429 Posts
|
Lucky penny ... not bad penny
Thanks so much Ron absolutely excellent.
__________________
Whoever said that "money can't buy you happiness" never bought a Luger. WTB - Take Down Lever & Trigger Plate (#90) for an Imperial Artillery.
|
|
|