1937 Luger Info

lwikeyl · 06-26-2010, 09:17 PM

Hey all...
I usually spend more time in other gun forums, they told me this is the spot for Luger info... My uncle has a Luger and he was looking for more info on it. I think he plans on selling it but it does not fire. He says when he pulls the trigger nothing happens. I told him to not get it fixed yet. As far as I can tell, all the number match, but I am not sure where all the stampings would be located. Thanks guys...

He said the gun shop thought that the part marked 58 in the pic above was broken causing it to not fire...

Does anybody know if this is the correct holster for this pistol? He actually has another one but he forgot which pistol was in the holster.

alanint · 06-27-2010, 04:07 PM

The holster is for an Artillery Luger.
Unfortunately, the gun you picture never left the factory that way. The long barrel is not original to the gun. It may still be a good shooter, but it has lost much of its collector value.
The part your gunshop people pointed out as perhaps being the culprit in the failure to fire is actually the extractor. A broken extractor may prevent a round from being properly removed from the chamber after firing, but will not influence a fire/no fire situation.
You need to have a competent gunsmith, with experience with Lugers determine why it will not fire.

HTHs

Ron Wood · 06-27-2010, 04:32 PM

The holster is a reproduction.

sheepherder · 06-27-2010, 04:45 PM

The barrel is stamped "7.65"...He's not trying to shoot 9mm cartridges in it, is he???

Any other markings on that barrel??? How about a side pic of the front sight???

Might be a good idea to post your location; someone knowledgeable may be able to recommend a member familiar with Lugers close to you...

lwikeyl · 06-27-2010, 06:48 PM

Thanks for the info guys. The gun is in the Minneapolis area. Any recommendations for a good smith to look at it?
As far as the extractor, that was what I thought, it would only affect ejecting the spent case, but I did not know for sure.
If the gun was in working condition, any idea of approximately what it would be worth?
Thanks for the help...

lwikeyl · 07-02-2010, 03:15 PM

Bump for approximate price if the pistol was in working order with holster?
Thanks guys

zinfull · 07-02-2010, 03:57 PM

I would guess that it would sell in CA for $6-$750. But a lot of people do not understand lugers.

jerry

sheepherder · 07-02-2010, 07:08 PM

There have been people on this site looking for a "target" Luger...Yours might be the basis for a paper punching Luger...Add a micrometer rear sight, a set of sculpted grips, and some careful tuning, and it just might turn out to be an accurate shooter...

Edward Tinker · 07-03-2010, 06:52 AM

I would say in its present condition $550-$650 as many folks would want to "tinker" with it.

With the problem fixed probably $700-$800

I would think that it could be several things, and yes, someone who KNOWSlugers should mess with it; most gunsmiths won't know what to check for.

Firing pin tip broken
Sideplate misalingment and it won't fire (most likely for my guns that I've had problems with)
Dirty as hell on the inside and things are just gummed.

Might be cheaper to sell as -is ??

Ed

tommyjoe · 07-03-2010, 11:39 AM

In it's present condition as pictured, the safty bar is blocking the sear.
Tom

lwikeyl · 07-03-2010, 01:36 PM

Wow, thanks guys, I really appreciate the info. I will let him know and see what he says. I am starting to like these pistols, I might have to get one or 20...

06-26-2010, 09:17 PM	#1
lwikeyl New User Join Date: Jun 2010 Posts: 4 Thanks: 7 Thanked 0 Times in 0 Posts	1937 Luger Info Hey all... I usually spend more time in other gun forums, they told me this is the spot for Luger info... My uncle has a Luger and he was looking for more info on it. I think he plans on selling it but it does not fire. He says when he pulls the trigger nothing happens. I told him to not get it fixed yet. As far as I can tell, all the number match, but I am not sure where all the stampings would be located. Thanks guys... He said the gun shop thought that the part marked 58 in the pic above was broken causing it to not fire... Does anybody know if this is the correct holster for this pistol? He actually has another one but he forgot which pistol was in the holster.

06-27-2010, 04:32 PM	#3
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 7,005 Thanks: 1,087 Thanked 5,139 Times in 1,689 Posts	The holster is a reproduction. __________________ If it's made after 1918...it's a reproduction

06-27-2010, 04:45 PM	#4
sheepherder Lifer Lifetime Forum Patron Join Date: Feb 2009 Location: ...on the 'ol Erie Canal... Posts: 8,182 Thanks: 1,400 Thanked 4,441 Times in 2,329 Posts	The barrel is stamped "7.65"...He's not trying to shoot 9mm cartridges in it, is he??? Any other markings on that barrel??? How about a side pic of the front sight??? Might be a good idea to post your location; someone knowledgeable may be able to recommend a member familiar with Lugers close to you... __________________ I like my coffee the way I like my women... ...Cold and bitter...

07-02-2010, 07:08 PM	#8
sheepherder Lifer Lifetime Forum Patron Join Date: Feb 2009 Location: ...on the 'ol Erie Canal... Posts: 8,182 Thanks: 1,400 Thanked 4,441 Times in 2,329 Posts	There have been people on this site looking for a "target" Luger...Yours might be the basis for a paper punching Luger...Add a micrometer rear sight, a set of sculpted grips, and some careful tuning, and it just might turn out to be an accurate shooter... __________________ I like my coffee the way I like my women... ...Cold and bitter...

06-27-2010, 04:07 PM	#2
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,916 Times in 1,192 Posts	The holster is for an Artillery Luger. Unfortunately, the gun you picture never left the factory that way. The long barrel is not original to the gun. It may still be a good shooter, but it has lost much of its collector value. The part your gunshop people pointed out as perhaps being the culprit in the failure to fire is actually the extractor. A broken extractor may prevent a round from being properly removed from the chamber after firing, but will not influence a fire/no fire situation. You need to have a competent gunsmith, with experience with Lugers determine why it will not fire. HTHs

06-27-2010, 06:48 PM	#5
lwikeyl New User Join Date: Jun 2010 Posts: 4 Thanks: 7 Thanked 0 Times in 0 Posts	Thanks for the info guys. The gun is in the Minneapolis area. Any recommendations for a good smith to look at it? As far as the extractor, that was what I thought, it would only affect ejecting the spent case, but I did not know for sure. If the gun was in working condition, any idea of approximately what it would be worth? Thanks for the help...

07-02-2010, 03:15 PM	#6
lwikeyl New User Join Date: Jun 2010 Posts: 4 Thanks: 7 Thanked 0 Times in 0 Posts	Bump for approximate price if the pistol was in working order with holster? Thanks guys

07-02-2010, 03:57 PM	#7
zinfull Lifer Lifetime Forum Patron Join Date: Dec 2004 Location: Sonoma County CA Posts: 243 Thanks: 4 Thanked 33 Times in 16 Posts	I would guess that it would sell in CA for $6-$750. But a lot of people do not understand lugers. jerry

07-03-2010, 06:52 AM	#9
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,924 Thanks: 2,014 Thanked 4,518 Times in 2,087 Posts	I would say in its present condition $550-$650 as many folks would want to "tinker" with it. With the problem fixed probably $700-$800 I would think that it could be several things, and yes, someone who KNOWSlugers should mess with it; most gunsmiths won't know what to check for. Firing pin tip broken Sideplate misalingment and it won't fire (most likely for my guns that I've had problems with) Dirty as hell on the inside and things are just gummed. Might be cheaper to sell as -is ?? Ed

07-03-2010, 11:39 AM	#10
tommyjoe User Join Date: Jul 2002 Location: Gray Ga. Posts: 13 Thanks: 0 Thanked 1 Time in 1 Post	In it's present condition as pictured, the safty bar is blocking the sear. Tom

07-03-2010, 01:36 PM	#11
lwikeyl New User Join Date: Jun 2010 Posts: 4 Thanks: 7 Thanked 0 Times in 0 Posts	Wow, thanks guys, I really appreciate the info. I will let him know and see what he says. I am starting to like these pistols, I might have to get one or 20...