Ejector gave up the ghost today

kurusu · 08-15-2016, 02:53 PM

Went shooting today (it's an holiday here). The ejector of shooter number two (S/42) gave up on me.

Luckily it's not a numbered part and I have spares.

Just finished installing it.

sheepherder · 08-15-2016, 03:07 PM

Quote:

Originally Posted by kurusu

Went shooting today (it's an holiday here). The ejector of shooter number two (S/42) gave up on me.

Luckily it's not a numbered part and I have spares.

Just finished installing it.

I am curious; did it break right at the pivot??? (Where it locks into the barrel extension/receiver). That seems like where the stress would concentrate...Kind of like bending a coat hanger...

kurusu · 08-15-2016, 03:17 PM

It broke the front tip just where it enters the barrel extension to do it's ejecting stuff.

rhuff · 08-15-2016, 04:14 PM

Quote:

Originally Posted by kurusu

It broke the front tip just where it enters the barrel extension to do it's ejecting stuff.

This is where I have experienced breakage on Luger extractors. I have had two(2) break in that area over the years.

kurusu · 08-15-2016, 04:28 PM

Quote:

Originally Posted by rhuff

This is where I have experienced breakage on Luger extractors. I have had two(2) break in that area over the years.

What's ironic is:

Shooter number 1 (a BYF 41) has had gazillion shots through it and the ejector still holds (knock on wood, cause I only have one other spare), shooter number 2 is quite recent in my hands and only has about 1k through it since I got it. But I suspect it's ejector was a newly made replacement. The one I installed now is an original. Let's wait and see.

sheepherder · 08-15-2016, 04:29 PM

Quote:

Originally Posted by rhuff

This is where I have experienced breakage on Luger extractors. I have had two(2) break in that area over the years.

So his ejector broke at the same place where your extractor broke??? Just want to get that straight in my mind's eye...

It would be some coincidence if both parts broke at the same time...

kurusu · 08-15-2016, 04:34 PM

Quote:

Originally Posted by sheepherder

So his ejector broke at the same place where your extractor broke??? Just want to get that straight in my mind's eye...

It would be some coincidence if both parts broke at the same time...

Now, don't you be mean. If I had a dollar bill for every time I said extractor meaning ejector. I wouldn't be rich... But I'd have enough money for a lobster dinner with a Champagne magnum to go with.

sheepherder · 08-15-2016, 05:02 PM

Quote:

Originally Posted by kurusu

Now, don't you be mean...

Just being snarky.

Rhuff could be talking about his extractor; I have one that broke/chipped the corner off at the forward end...

I hate the ejectors; It always seems like I'm going to break one whenever I remove/replace it...

kurusu · 08-15-2016, 05:20 PM

Quote:

Originally Posted by sheepherder

I hate the ejectors; It always seems like I'm going to break one whenever I remove/replace it...

Mine wasn't easy going into place either.

DonVoigt · 08-15-2016, 08:00 PM

I've had one or two with the "arm" the part that does the ejecting, too short.
Look ok on inspection, but don't work well at all.

Seems most of the ejectors I've installed required some tweaking to snap in correctly; usually at the round "retainer" at the back of the ejector that fits into the receiver hole to lock it in fore and aft. Sometimes the overall length is too long at the back too.

Kind of hard to tell original from used reproductions, but I'm sure some were/are that I have used.

lugerholsterrepair · 08-15-2016, 09:34 PM

Who's on first? Hard to filter out what you guys are talking about..Ejector, extractor, extractor, ejector...

alanint · 08-16-2016, 09:23 AM

" Let's call the whole thing off"!

kurusu · 08-16-2016, 01:18 PM

Quote:

Originally Posted by DonVoigt

I've had one or two with the "arm" the part that does the ejecting, too short.
Look ok on inspection, but don't work well at all.

Seems most of the ejectors I've installed required some tweaking to snap in correctly; usually at the round "retainer" at the back of the ejector that fits into the receiver hole to lock it in fore and aft. Sometimes the overall length is too long at the back too.

Kind of hard to tell original from used reproductions, but I'm sure some were/are that I have used.

The replacement had visually the same dimensions. After installed I ran manually a full magazine and it ejected positively. Next weekend I'll know for sure if it works fine.

And yes, it did take some "persuasion" (and a few selected words)

to snap into place.

rhuff · 08-16-2016, 03:45 PM

Quote:

Originally Posted by rhuff

This is where I have experienced breakage on Luger extractors. I have had two(2) break in that area over the years.

Sorry all. I read ejector and brain said extractor......brain fade!!! I am sure that this has nothing to do with a "senior brain malfunction". I will try to do better, but no guarentees.

sheepherder · 08-16-2016, 04:17 PM

Quote:

Originally Posted by rhuff

....brain fade!!! I am sure that this has nothing to do with a "senior brain malfunction".

So...I am not alone...

kurusu · 08-16-2016, 04:18 PM

Quote:

Originally Posted by sheepherder

So...I am not alone...

You wish.

kurusu · 08-20-2016, 12:06 PM

Just finished a training session. The new ejector works flawlessly.

Zorba · 08-21-2016, 12:56 PM

Quote:

Originally Posted by lugerholsterrepair

Who's on first? Hard to filter out what you guys are talking about..Ejector, extractor, extractor, ejector...

But is it a magazine or a clip?

*runs away*

sheepherder · 08-21-2016, 03:29 PM

Quote:

Originally Posted by Zorba

But is it a magazine or a clip?

Is it a barrel extension or a receiver???

kurusu · 08-21-2016, 05:14 PM

Quote:

Originally Posted by Zorba

But is it a magazine or a clip?

*runs away*

Come back!!

I'll tell you.

Listen very carefully, I shall say this only once.

In a Luger pistol it's a magazine.

In a C96 you load it's magazine (fixed in most models) from a clip.

Was that clear?

08-15-2016, 02:53 PM	#1
kurusu User Join Date: Sep 2007 Posts: 1,225 Thanks: 2,679 Thanked 930 Times in 509 Posts	Ejector gave up the ghost today Went shooting today (it's an holiday here). The ejector of shooter number two (S/42) gave up on me. Luckily it's not a numbered part and I have spares. Just finished installing it.

08-15-2016, 08:00 PM	#10
DonVoigt User Join Date: Apr 2015 Location: near Charlotte NC Posts: 4,681 Thanks: 1,443 Thanked 4,355 Times in 2,041 Posts	I've had one or two with the "arm" the part that does the ejecting, too short. Look ok on inspection, but don't work well at all. Seems most of the ejectors I've installed required some tweaking to snap in correctly; usually at the round "retainer" at the back of the ejector that fits into the receiver hole to lock it in fore and aft. Sometimes the overall length is too long at the back too. Kind of hard to tell original from used reproductions, but I'm sure some were/are that I have used. __________________ 03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie

08-15-2016, 09:34 PM	#11
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,775 Thanks: 4,995 Thanked 3,133 Times in 1,439 Posts	Who's on first? Hard to filter out what you guys are talking about..Ejector, extractor, extractor, ejector... __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 lugerholsterrepair@earthlink.net 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

08-20-2016, 12:06 PM	#17
kurusu User Join Date: Sep 2007 Posts: 1,225 Thanks: 2,679 Thanked 930 Times in 509 Posts	Update Just finished a training session. The new ejector works flawlessly.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-15-2016, 03:17 PM	#3
kurusu User Join Date: Sep 2007 Posts: 1,225 Thanks: 2,679 Thanked 930 Times in 509 Posts	It broke the front tip just where it enters the barrel extension to do it's ejecting stuff.

08-16-2016, 09:23 AM	#12
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,917 Times in 1,193 Posts	" Let's call the whole thing off"!