Question Regarding Imperial Rod

[cirelaw]

Why would anyone bother!!!

[sheepherder]

I am interested in knowing how the machinist that did this grease barrel knurled it with a single-direction knurl???

I've attached a pic of the grease barrel and a scan of knurling rollers...there is basically only two knurls; the crosshatch, and the straight knurl...In different pitches, but that's about it...

The only way I can think of to get a single-direction knurl is using two identical sets of knurl rollers, and use both right rollers or both left rollers, of the cross hatch set...

Even then they would have a tendency to 'ride off' to the side while knurling...

(The clamp type tool post knurling tool in the pic is the one I received; replaces the 'run it in' knurling tool I've used up to now - it is much better)...

And looking close, Neil hit it on the head...That grease barrel is crude...

[sheepherder]

Originally Posted by cirelaw

Why would anyone bother!!!

...Because it is there...

[Norme]

Originally Posted by postino

...???...Patrice's original screws into the barrel as well...

Hi Rich, The shafts on original rods are hard soldered to the handles. I don't know whether they are threaded or not.
Regards, Norm

[sheepherder]

Originally Posted by Norme

Hi Rich, The shafts on original rods are hard soldered to the handles. I don't know whether they are threaded or not.
Regards, Norm

OK, I need a little help here...Are you talking about the entire full length of the rod being soldered to the grease pot clamp??? Or just the stub that I can see the rod being inserted into??? Whether or not the brass rod is soldered or threaded into the stub...

Is the brass rod w/auger supposed to be removable???

I don't think I can understand this without looking at/inspecting one...

[LU1900]

Easy with paint , so , new light
About the inside , the rod go to be level , flush(dictionary) so , only we see the brass cercle for 4 or 5 mm
/
Got also a french rod for the "manufacture" luger , with also like the gun have inventory number stamped , and the milling brass is 45 ° from standard one's .

[lugerholsterrepair]

Why would anyone bother!!!

Eric..One good reason and one only that I can think of. The 02 Carbine was a civilian Pistol /rifle and as such it employed the grease barrel type cleaning rod. It would really be magical to be able to reproduce an accurate rod for Carbines.

Original Carbine grease barrel rods are like hens teeth and would cost you about $800-1,000. That's IF you ever find one for sale in your lifetime.

[cirelaw]

Do we know who produced these wonderful accessories?

[Neil Young]

You would bother because it is a challenge. If you successfully build a sterling example, you have accomplished something that very few people could do. It would make you very proud. I know that that sounds a little like BS (or maybe a lot), but it is true.

[Neil Young]

..I would guess it would be a tad difficult to accurately make one of these grease barrel rods?

I think you are absolutely right Jerry--it would really be difficult.

Jerry, I can do pretty good on some small, tedious projects, but I am not a really good craftsman. There are people on this forum who are, in my estimation, Master Craftsmen. The two that I can think of offhand are Olle and Postino. I know that there are others that I am forgetting, or just don't know about. Check out some of their work--it's awesome!

[sheepherder]

Originally Posted by Neil Young

There are people on this forum who are, in my estimation, Master Craftsmen. The two that I can think of offhand are Olle and Postino.

... ...

Speed kills, Neil!!!

[cirelaw]

The 1906 French Commercial as seen in Kenyans' book, Lugers At Random, page 106 includes the subject of debate!~~~Eric

[lugerholsterrepair]

Neil, I am sure you are too bashful..I have seen your work. Having asked you and others to do the impossible..I know.

I should make a list someday..I have done a lot of projects that took real skill.. My Trommel magazine box, wood.. Kris Antzak metal hardware Craig Creswell. Carbine rods and small loop Luger rods, Neil Young. Dutch pin punch, Craig again. I generally take on rare projects and only accept the best. I have many more but will have to put it all together someday.

I will have to say there are many masters of their craft out there. Always a joy to see the fantastic stuff they make.

[Ron Wood]

Man, I love this hobby! The master craftsmen listed in the previous posts, including Jerry, contribute so much to the continued enjoyment, preservation and augmentation of items that are part of history. And they are real gentlemen. If you have ever met any of them in person or through correspondence you know that you are in rare company. Thanks guys!

[lugerholsterrepair]

Rich..The single knurling is proclaimed by some in the past to be original and correct but I have never been a proponent of that line of thinking.

Any rod I ever inspected I thought was real had a crosshatch knurl, a fixed rod to the barrel and was finely made. I believe I have one around here..but it's missing the top. I always thought I would stumble across an orphan top but I never have.

[sheepherder]

Originally Posted by lugerholsterrepair

Rich..The single knurling is proclaimed by some in the past to be original and correct but I have never been a proponent of that line of thinking...

The knurl on the barrel top you mean??? Do you know how they did it???

[cirelaw]

Does the fact that both are different make any difference in anyones' opinion? Do we know from who produced them and when?

[lugerholsterrepair]

Rich..No I don't.

Eric, Both or your rods screw into the barrel and that is what concerns me about them.

[sheepherder]

Originally Posted by lugerholsterrepair

Eric, Both or your rods screw into the barrel and that is what concerns me about them.

...???...Patrice's original screws into the barrel as well...

[cirelaw]

A good point!!!