Luger Parts

Bob51 · 07-19-2011, 09:27 AM

I have the following lugar parts can anyone give me a value and description? these parts have the number 88 stamped on them with the exception of the thumb bolt which has the number 100 stamped on it. The main bolt has DMC engraveing

Edward Tinker · 07-19-2011, 09:43 AM

top is a DWM Luger toggle, does it have the firing pin, do all the parts match (push in with a screw driver, and slightly turn, don't force), or pull toggle down so it knees and look and see if you can see the sn value $100-$150, but its in rougher shape so... (see spelling, common mistake)

The L shaped and the one below it go to the recoil spring, $30 maybe

then left, down, then right and down
Hold-open, if numbered and not pitted, $45

Sear worth around $25

Take down, depends on how good of shape, $45-$55

Magazine latch, $20

ed_tinker@hotmail.com

I am always looking for parts

Ed

alanint · 07-19-2011, 09:53 AM

These parts look like they survived a fire, so temper may be an issue.

Bob51 · 07-19-2011, 10:18 AM

Yes the firing pin is there but I can see no number on it. The hold open is numbered 88

Thanks

sheepherder · 07-19-2011, 11:59 AM

Quote:

Originally Posted by Edward Tinker

top is a DWM Luger toggle, does it have the firing pin, do all the parts match (push in with a screw driver, and slightly turn, don't force), or pull toggle down so it knees and look and see if you can see the sn value $100-$150, but its in rougher shape so...

Ed- that's a Navy toggle; complete with sight...I should think it would be worth a bit more than $150...

lugerholsterrepair · 07-19-2011, 12:00 PM

Bob, Can you confirm if these have been in a fire?

Bob51 · 07-19-2011, 12:44 PM

Thanks Guys for the information

I do not know about any fire but who knows.... the parts were in the bottom of his ww2 dufflebag wrapped in waxed paper. Thanks for the explanation about the sight.....it is a 2 position sight. I could not figure the 100 stamp...now..... I know 100 meters and 200 meters I would say it that it is somewhat unsual as my lugar does not have this feature. Maybe why dad wanted to save it.

Bob51

lugerholsterrepair · 07-19-2011, 01:00 PM

Bob, There may be a way to determine this. Open the sight by pushing the button on the right side..slide the sight back..on a Navy sight the interior should be in the white. If it is in the white and perhaps either rusty or corroded OK. If it is fire blued or black it has achieved a temperature 5-600 degrees or higher.

Bob51 · 07-19-2011, 01:36 PM

Everything looks ok.....not blue or black just a little rusty

Edward Tinker · 07-19-2011, 02:07 PM

Quote:

Originally Posted by postino

Ed- that's a Navy toggle; complete with sight...I should think it would be worth a bit more than $150...

Thats nice. Venture a guess as to value, instead of pointing out a mistake

Ron Wood · 07-19-2011, 02:38 PM

Wrong answer Ed. Postino didn't appraise the toggle, you did, and mistakenly. He only politely gave you a chance to amend your value.

Edward Tinker · 07-19-2011, 03:40 PM

Ron, a PM or email and tell me I made a mistake instead of publicly pointing it out would have been nice.

You are welcome to give a value, as is anyone else here, but I am not going to; others can do the moderating.

Ron Wood · 07-19-2011, 04:12 PM

Quote:

Originally Posted by Edward Tinker

Ron, a PM or email and tell me I made a mistake instead of publicly pointing it out would have been nice.

You are welcome to give a value, as is anyone else here, but I am not going to; others can do the moderating.

I apologize Ed. Rest assured I will not do it again. I think a lot of you and the efforts you put into both forums...not many people would sacrifice their time to do the job you do. A PM would have been a better alternative, so thank you for pointing that out.

Having said that, you are quick to call out someone that has erred, so I guess we are birds of a feather. To my mind, the proper response to Postino's post would have been: "oops, I didn't notice that, thank you for pointing it out", and then, in your experience you might have given an alternative value if you wanted to.

You are in the business of buying, selling and trading all the time, much more than me. I occasionally will venture a guess on the value of a scarce/rare early item, but for the most part have no idea of what the current market is on anything. I rely on guys like you to keep me informed, and when you obviously have mis-valued something, I think you should have the opportunity to use your enviable expertise to make a correction.
Very respectfully,
Ron

Bob51 · 07-19-2011, 05:00 PM

Hang on Guys........any and all advise, comments, and suggestions are welcome. The knowledge of the least of you guys is more than I can ever hope to have. I am researching these parts form a number of sources and seeing lots of different opinions on their value. But the truth of the matter is this these parts are not doing anyone any good sitting in my drawer. My father was not a collector just an infantryman turned mechanic. The only pistol he ever owned was this old 1914 lugar. I do know there was a reason he kept the parts for all these years......not for replacement parts but maybe for their unsualness. Who knows. I also know he would roll over in his grave if I did not do the research and find a good home and a fair price. He would want these to go to someone who knows their value and could put then back into action. So having said that I really appreciate all the comments so far and hope to see more. Thank-you guys for your forum and your help

Bob51

Kitkat041836 · 07-19-2011, 05:11 PM

Hi Bob
I sent you a private PM could you please call me at 1-(510)-523-6682.
Thank you George

sheepherder · 07-19-2011, 05:27 PM

Quote:

Originally Posted by Edward Tinker

Ron, a PM or email and tell me I made a mistake instead of publicly pointing it out would have been nice.

Sorry Ed; my bad.

Not trying to embarrass you; just thought that the original pics were so dark that you didn't immediately notice the '100' on the second pic (which led me to download & lighten the first pic to be sure).

I don't have any experience with Navy Lugers; haven't even seen one. It was my thought that you could give a better estimate than I could. I'm pretty sure I've seen Rich/rwc on GB sell Navy toggles for $350 (or at least ask that much). Seems high to me, but he seems to thrive...

Edit: Correction - The BIN on the GB Navy toggle is $550...

http://www.gunbroker.com/Auction/Vie...Item=242495399

Lugerdoc · 07-20-2011, 01:21 PM

Bob, It's a shame that your Navy toggle assy got rusted. I'm afraid that the pits in the knurlled area with be near impossible to get out and restore properly. Not that an expert restorer couldn't do it, but it probably would cost more to restore than you are asking. I'd still be willing to take a closer look and make you an offer. TH

Bob51 · 07-20-2011, 01:56 PM

Thanks Tom I appreciate the input....... can't change what they are......wish they were brand new still in the oil cloth....would make things a lot easier.

Bob51 · 07-20-2011, 05:33 PM

Thanks Again everone for your comments and advice. I must say I have had some interesting offers some some worth serious consideration.= and some obviously not. I am in no real hurry here as the real or percieved value can in no way equal the memories and storys behind these found pieces. This is a one time effort on my part as they will never show up again in my lifetime. Lets let this thread play out and give it time to find the intrested parties and i am sure the true value will be seen. It is not about the money as this sale will not effectively change my life its all about finding the real value and getting these parts into the hands of who can best utilize them. Like I said before they are what they are.

Bob51 · 07-20-2011, 06:28 PM

some have ask for more pictures... Here goes. These were taken after cleaning with wd40 and paper towel

07-19-2011, 09:27 AM	#1
Bob51 User Join Date: Jul 2011 Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts	Luger Parts I have the following lugar parts can anyone give me a value and description? these parts have the number 88 stamped on them with the exception of the thumb bolt which has the number 100 stamped on it. The main bolt has DMC engraveing Attached Thumbnails

07-19-2011, 12:00 PM	#6
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,775 Thanks: 4,995 Thanked 3,133 Times in 1,439 Posts	Bob, Can you confirm if these have been in a fire? __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 lugerholsterrepair@earthlink.net 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

07-19-2011, 12:44 PM	#7
Bob51 User Join Date: Jul 2011 Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts	Thanks for the replys Thanks Guys for the information I do not know about any fire but who knows.... the parts were in the bottom of his ww2 dufflebag wrapped in waxed paper. Thanks for the explanation about the sight.....it is a 2 position sight. I could not figure the 100 stamp...now..... I know 100 meters and 200 meters I would say it that it is somewhat unsual as my lugar does not have this feature. Maybe why dad wanted to save it. Bob51

07-19-2011, 01:00 PM	#8
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,775 Thanks: 4,995 Thanked 3,133 Times in 1,439 Posts	Bob, There may be a way to determine this. Open the sight by pushing the button on the right side..slide the sight back..on a Navy sight the interior should be in the white. If it is in the white and perhaps either rusty or corroded OK. If it is fire blued or black it has achieved a temperature 5-600 degrees or higher. __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 lugerholsterrepair@earthlink.net 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

07-19-2011, 01:36 PM	#9
Bob51 User Join Date: Jul 2011 Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts	Everything looks ok.....not blue or black just a little rusty Attached Thumbnails

07-19-2011, 09:43 AM	#2
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,967 Thanks: 2,066 Thanked 4,595 Times in 2,116 Posts	top is a DWM Luger toggle, does it have the firing pin, do all the parts match (push in with a screw driver, and slightly turn, don't force), or pull toggle down so it knees and look and see if you can see the sn value $100-$150, but its in rougher shape so... (see spelling, common mistake) The L shaped and the one below it go to the recoil spring, $30 maybe then left, down, then right and down Hold-open, if numbered and not pitted, $45 Sear worth around $25 Take down, depends on how good of shape, $45-$55 Magazine latch, $20 ed_tinker@hotmail.com I am always looking for parts Ed

07-19-2011, 09:53 AM	#3
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,917 Times in 1,193 Posts	These parts look like they survived a fire, so temper may be an issue.

07-19-2011, 10:18 AM	#4
Bob51 User Join Date: Jul 2011 Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts	Yes the firing pin is there but I can see no number on it. The hold open is numbered 88 Thanks

07-19-2011, 02:38 PM	#11
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 7,040 Thanks: 1,106 Thanked 5,257 Times in 1,724 Posts	Wrong answer Ed. Postino didn't appraise the toggle, you did, and mistakenly. He only politely gave you a chance to amend your value. __________________ If it's made after 1918...it's a reproduction

07-19-2011, 03:40 PM	#12
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,967 Thanks: 2,066 Thanked 4,595 Times in 2,116 Posts	Ron, a PM or email and tell me I made a mistake instead of publicly pointing it out would have been nice. You are welcome to give a value, as is anyone else here, but I am not going to; others can do the moderating.

07-19-2011, 05:00 PM	#14
Bob51 User Join Date: Jul 2011 Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts	Hang on Guys........any and all advise, comments, and suggestions are welcome. The knowledge of the least of you guys is more than I can ever hope to have. I am researching these parts form a number of sources and seeing lots of different opinions on their value. But the truth of the matter is this these parts are not doing anyone any good sitting in my drawer. My father was not a collector just an infantryman turned mechanic. The only pistol he ever owned was this old 1914 lugar. I do know there was a reason he kept the parts for all these years......not for replacement parts but maybe for their unsualness. Who knows. I also know he would roll over in his grave if I did not do the research and find a good home and a fair price. He would want these to go to someone who knows their value and could put then back into action. So having said that I really appreciate all the comments so far and hope to see more. Thank-you guys for your forum and your help Bob51

07-19-2011, 05:11 PM	#15
Kitkat041836 RIP Join Date: Feb 2009 Posts: 195 Thanks: 0 Thanked 21 Times in 18 Posts	Navy parts Hi Bob I sent you a private PM could you please call me at 1-(510)-523-6682. Thank you George

07-20-2011, 01:21 PM	#17
Lugerdoc Patron LugerForum Patron Join Date: Jun 2002 Location: POB 398 St.Charles,MO. 63302 Posts: 5,089 Thanks: 6 Thanked 737 Times in 484 Posts	Bob, It's a shame that your Navy toggle assy got rusted. I'm afraid that the pits in the knurlled area with be near impossible to get out and restore properly. Not that an expert restorer couldn't do it, but it probably would cost more to restore than you are asking. I'd still be willing to take a closer look and make you an offer. TH __________________ Tom Heller POB 398 ST.Charles, MO. 63302 Tel 636-447-3006 lugerdoc@charter.net

07-20-2011, 01:56 PM	#18
Bob51 User Join Date: Jul 2011 Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts	Thanks Tom I appreciate the input....... can't change what they are......wish they were brand new still in the oil cloth....would make things a lot easier.

07-20-2011, 05:33 PM	#19
Bob51 User Join Date: Jul 2011 Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts	Thanks Again everone for your comments and advice. I must say I have had some interesting offers some some worth serious consideration.= and some obviously not. I am in no real hurry here as the real or percieved value can in no way equal the memories and storys behind these found pieces. This is a one time effort on my part as they will never show up again in my lifetime. Lets let this thread play out and give it time to find the intrested parties and i am sure the true value will be seen. It is not about the money as this sale will not effectively change my life its all about finding the real value and getting these parts into the hands of who can best utilize them. Like I said before they are what they are.

07-20-2011, 06:28 PM	#20
Bob51 User Join Date: Jul 2011 Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts	More Pictures some have ask for more pictures... Here goes. These were taken after cleaning with wd40 and paper towel Attached Thumbnails

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode