Safety Repair

captcraig · 05-04-2011, 12:14 AM

I just picked up a 1940 Vet Bring back, one problem the inside safety lever is broken off. If I can find another safety can this be replaced?

alanint · 05-04-2011, 06:34 AM

Yes, the safety can be removed by driving out a small internal pin. If it is a question of welding back the little link, this is preferable as the outside thumb lever will most likely be numbered to the gun. Replacing the part entirely would make this a mismatched part, unless you are lucky enough to locate a similarly numbered part.

LugerDoc, (Tom Heller) here on the boards can most likely repair this part or possibly have a matching part as replacement.
Good Luck!

jamese · 05-04-2011, 08:37 AM

I have a few, what number are you looking for ? I might have an unnumbered one as well

Jim

Lugerdoc · 05-04-2011, 10:05 AM

Capt. Craig, I do have a lot of exc Mauser safety levers & bars in stock. Just be sure that you get a Mauser one to match your PO8, as any other maker will use a different die numbering set and earlier ones have their serial in a slightly different location. TH

Ron Wood · 05-04-2011, 11:20 AM

I am not sure what you mean by "inside" safety lever. Do you mean the bottom part of the safety lever that is under the grip?

captcraig · 05-04-2011, 11:23 AM

Thank You to every one for your replies. The Safety is numberd 04. I am also looking for a side plate with the same number.

captcraig · 05-04-2011, 11:25 AM

Yes, I am refering to the lever on the inside under the grip.

05-04-2011, 12:14 AM	#1
captcraig User Join Date: Mar 2008 Posts: 27 Thanks: 5 Thanked 0 Times in 0 Posts	Safety Repair I just picked up a 1940 Vet Bring back, one problem the inside safety lever is broken off. If I can find another safety can this be replaced?

05-04-2011, 08:37 AM	#3
jamese User Join Date: Jan 2003 Location: South Florida Posts: 792 Thanks: 0 Thanked 86 Times in 36 Posts	I have a few, what number are you looking for ? I might have an unnumbered one as well Jim __________________ The "truth" is a matter of Perception

05-04-2011, 10:05 AM	#4
Lugerdoc Patron LugerForum Patron Join Date: Jun 2002 Location: POB 398 St.Charles,MO. 63302 Posts: 5,089 Thanks: 6 Thanked 737 Times in 484 Posts	Capt. Craig, I do have a lot of exc Mauser safety levers & bars in stock. Just be sure that you get a Mauser one to match your PO8, as any other maker will use a different die numbering set and earlier ones have their serial in a slightly different location. TH __________________ Tom Heller POB 398 ST.Charles, MO. 63302 Tel 636-447-3006 lugerdoc@charter.net

05-04-2011, 11:20 AM	#5
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 7,040 Thanks: 1,106 Thanked 5,257 Times in 1,724 Posts	I am not sure what you mean by "inside" safety lever. Do you mean the bottom part of the safety lever that is under the grip? __________________ If it's made after 1918...it's a reproduction

05-04-2011, 11:23 AM	#6
captcraig User Join Date: Mar 2008 Posts: 27 Thanks: 5 Thanked 0 Times in 0 Posts	Luger Safety Thank You to every one for your replies. The Safety is numberd 04. I am also looking for a side plate with the same number.

05-04-2011, 06:34 AM	#2
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,917 Times in 1,193 Posts	Yes, the safety can be removed by driving out a small internal pin. If it is a question of welding back the little link, this is preferable as the outside thumb lever will most likely be numbered to the gun. Replacing the part entirely would make this a mismatched part, unless you are lucky enough to locate a similarly numbered part. LugerDoc, (Tom Heller) here on the boards can most likely repair this part or possibly have a matching part as replacement. Good Luck!

05-04-2011, 11:25 AM	#7
captcraig User Join Date: Mar 2008 Posts: 27 Thanks: 5 Thanked 0 Times in 0 Posts	Safety Yes, I am refering to the lever on the inside under the grip.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode