New/Old Commercial Model - Info Requested

calibrator · 04-21-2009, 10:44 PM

Apparently the Abyss of Lost Replies. I was posting the above to something else that seems to have vanished. Good Luck Whoever you are!! Joe

sheepherder · 04-21-2009, 10:51 PM

Looks pretty clean inside...No rust...Goodly amount of bluing left, except where you would expect a holster to wear...

Barrel is a darker black than the rest of the pistol...and the rear slant of the front sight isn't lined up in a straight line like my other Luger barrels...

Numbers all match [82], except no number on breechblock or firing pin...Aftermarket mag w/steel extruded body & plastic 2-pin base...

sheepherder · 04-21-2009, 11:15 PM

No corrosion under grips...and aftermarket grips fit very snug, and are thinner than the Indian grips so prevalent nowadays...

sheepherder · 04-21-2009, 11:17 PM

Well maintained, as far as I can tell...

sheepherder · 04-21-2009, 11:19 PM

Import stamp on left gripframe rail...Crown/N on left chamber side...lazy Crown/N on breechblock...

sheepherder · 04-21-2009, 11:34 PM

Sorry for all the confusion!!! I had all my comments in post #1, and I could only upload 2-3 pics per post, so I tried to go back in and switch pics around and add the comments with the pics...

...It didn't work...

Anyway...Any comments, info, flames etc please post!!!

Oh, it's 30 cal/7.65 Luger...

The trigger, ejector, mag release, safety, and takedown lever still show strawing...Sideplate is worst worn, but has correct number on bottom...All edges are nice & sharp, doesn't appear to have been refinished...

sheepherder · 04-21-2009, 11:36 PM

Quote:

Originally Posted by calibrator

Apparently the Abyss of Lost Replies. I was posting the above to something else that seems to have vanished. Good Luck Whoever you are!! Joe

Don't give up, Joe!!! I seem to be experiencing technical difficulties...

Ice · 04-22-2009, 08:20 AM

That is a very nice Commercial. The little wear just adds character and the aftermarket grips look very good. Good deal; bet it was hard to wait for so long before you picked it up.

sheepherder · 04-22-2009, 06:10 PM

Quote:

Originally Posted by Ice

Good deal; bet it was hard to wait for so long before you picked it up.

Didn't have a choice...The dealers' State Sales Permit expired and he had to re-apply all over again...Couldn't buy or sell handguns until it was re-issued. I had bought it on AuctionArms.com and had it shipped to him...Just when the permit expired...

It, and about 20+ other pistols, sat for three months...

Rifles, shotguns, and ammo were unaffected...New York State has a separate sales permit just for pistols/handguns...

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

04-21-2009, 10:44 PM	#1
calibrator User Join Date: Feb 2009 Location: Cave Creek Posts: 340 Thanks: 67 Thanked 271 Times in 108 Posts	Apparently the Abyss of Lost Replies. I was posting the above to something else that seems to have vanished. Good Luck Whoever you are!! Joe

04-21-2009, 11:34 PM	#6
sheepherder Lifer Lifetime Forum Patron Join Date: Feb 2009 Location: ...on the 'ol Erie Canal... Posts: 8,208 Thanks: 1,425 Thanked 4,474 Times in 2,343 Posts	Sorry for all the confusion!!! I had all my comments in post #1, and I could only upload 2-3 pics per post, so I tried to go back in and switch pics around and add the comments with the pics... ...It didn't work... Anyway...Any comments, info, flames etc please post!!! Oh, it's 30 cal/7.65 Luger... The trigger, ejector, mag release, safety, and takedown lever still show strawing...Sideplate is worst worn, but has correct number on bottom...All edges are nice & sharp, doesn't appear to have been refinished...

04-22-2009, 08:20 AM	#8
Ice User Join Date: Mar 2009 Location: Texas Posts: 552 Thanks: 13 Thanked 69 Times in 57 Posts	That is a very nice Commercial. The little wear just adds character and the aftermarket grips look very good. Good deal; bet it was hard to wait for so long before you picked it up.