Malfunction

Don · 12-19-2002, 12:47 PM

My 1917 DWM shooter is developing a problem. Every few rounds or so the cannon seems to go too far back and the pin slides out just a hair, which freezes the cannon in the rearward position. Has anybody had this happen to them? Thanks, guys.

unspellable · 12-19-2002, 01:49 PM

This is the reason for the frame hump on the vintage Mausers, and the oversized pin head on the Swiss and re-intro Mausers. But, on the other hand, I have never encountered an actual case of this problem in a DWM.

Are the receiver and frame matched? Is the pin in good condition? Especially the head flange?

Don · 12-19-2002, 02:58 PM

The receiver & frame are "matched," but I put that in quotes because I think that some parts on the gun have been renumbered. I'll check the pin tonight, but I think it was OK. The problem seems to be with the fact that the cannon goes back so far that the pin is completely exposed.

John Sabato · 12-19-2002, 03:40 PM

As unspellable has said, the problem you have described is the reason for the later production changes of "bumps" on the back of the Luger frame, and a larger flange on the pin...

I think it is possible that your main/recoil spring may have been shortened or at the very least weakened so that the slide travel past the frame ears... Solution? a new proper length Wolfe spring.

Don · 12-19-2002, 03:44 PM

a #38?

Doubs · 12-19-2002, 07:03 PM

[quote]Originally posted by Don:
<strong>a #38?</strong><hr></blockquote>

The 38# spring is "standard" and rated to replace the factory spring. Wolffe also makes a 36 and a 40# spring and sells all three as a "set". I'd try the 38# first.

12-19-2002, 12:47 PM	#1
Don User Join Date: Jun 2002 Location: Texas Posts: 146 Thanks: 0 Thanked 0 Times in 0 Posts	Malfunction My 1917 DWM shooter is developing a problem. Every few rounds or so the cannon seems to go too far back and the pin slides out just a hair, which freezes the cannon in the rearward position. Has anybody had this happen to them? Thanks, guys.

12-19-2002, 03:40 PM	#4
John Sabato Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: The Capital of the Free World Posts: 10,156 Thanks: 3,003 Thanked 2,309 Times in 1,098 Posts	As unspellable has said, the problem you have described is the reason for the later production changes of "bumps" on the back of the Luger frame, and a larger flange on the pin... I think it is possible that your main/recoil spring may have been shortened or at the very least weakened so that the slide travel past the frame ears... Solution? a new proper length Wolfe spring. __________________ regards, -John S "...We hold these truths to be self-evident that ALL men are created EQUAL *and are endowed by their Creator* with certain UNALIENABLE* rights, and among these are life, LIBERTY, and the pursuit of happiness..."*

12-19-2002, 01:49 PM	#2
unspellable User Join Date: Jun 2002 Location: Iowa Posts: 769 Thanks: 0 Thanked 20 Times in 12 Posts	This is the reason for the frame hump on the vintage Mausers, and the oversized pin head on the Swiss and re-intro Mausers. But, on the other hand, I have never encountered an actual case of this problem in a DWM. Are the receiver and frame matched? Is the pin in good condition? Especially the head flange?

12-19-2002, 02:58 PM	#3
Don User Join Date: Jun 2002 Location: Texas Posts: 146 Thanks: 0 Thanked 0 Times in 0 Posts	The receiver & frame are "matched," but I put that in quotes because I think that some parts on the gun have been renumbered. I'll check the pin tonight, but I think it was OK. The problem seems to be with the fact that the cannon goes back so far that the pin is completely exposed.

12-19-2002, 03:44 PM	#5
Don User Join Date: Jun 2002 Location: Texas Posts: 146 Thanks: 0 Thanked 0 Times in 0 Posts	a #38?

12-19-2002, 07:03 PM	#6
Doubs User Join Date: Jun 2002 Location: Byron, Georgia Posts: 1,742 Thanks: 826 Thanked 1,788 Times in 590 Posts	[quote]Originally posted by Don: <strong>a #38?</strong><hr></blockquote> The 38# spring is "standard" and rated to replace the factory spring. Wolffe also makes a 36 and a 40# spring and sells all three as a "set". I'd try the 38# first.