Gunparts

HÃ?Â¥kan Spuhr · 06-02-2001, 11:48 PM

As we are rebuild lugers for target shooting we do often need certain gunparts as extractors and ejectors.

We have earlyer orderd such from Gunparts corporation and just recived cast ****.

Parts that made just to make money on and not to shot with.

I don't mind if the parts is new as its only for target guns, but they have to be good.

Do anyone here have any ideas, is here someone that make their own extractors and ejectors?

I will maybe have the extractors made up, and replace the little hook that always breaks with a small ring, like the swiss extractors. But this is an expensive way.

I have also orderd new manufactured rear toggles with the sightbase for a Bomar sight in one piece with the toggle.

Those toggles are also greatly imporve both in steelquality ( worst swedish tooolsteel) and thicker material where the toggles normally crack.

Regards HÃ?Â¥kan

http://www.vapensmedjan.com

Thor · 06-03-2001, 12:43 AM

Tom Heller can supply you with original parts! I have bought lots of spare parts from him and they are quality parts! ~Thor~

Patrick · 06-03-2001, 03:19 AM

H. At the recent Berlin gun show, I saw a rack full of ex-VoPo rear toggle links that had, I suppose, been made in ex-East Germany. And also about twenty half-finished extruded mags (I now wish I had bought some). You can get quite good extractors here - BUT - not all of them fit without having to be touched up a bit. Patrick

06-03-2001, 07:00 AM

I agree that most large firms that just advertise one price for these items, is probably going to send you either a new repro or an original with a grade 2 finish, unless you are extreemly lucky. That's why my prices vary based on type and quality. Extractors: original externally numbered military @$40 exc, $30 vg, unnumbered unissued spares $50. Internally numbered DWM commericals @$50 exc. Also have new unissued Mauser Parabellum (same loop design as M29 Swiss) @$60 or with Swiss proof $75. Also have Erfurt or Simson proofed ones in this price range. New repros that require a lot of fitting @$25. Same basic prices & types will apply to ejectors, but these of course are all unnumbered.

HÃ?Â¥kan Spuhr · 06-03-2001, 11:40 AM

Thanks a lot for the responses.

Will the Mauser parabellum extractors with loop fit a P08?

I don't care so much about the condition of the parts as the quality, though we are rebuilding and rebluing all of them anyway.

About magazines I have been extremely happy with tripple K stainless mags, they have proved to work great in our guns.

Regards HÃ?Â¥kan

http://www.vapensmedjan.com

Kyrie · 06-03-2001, 01:12 PM

Hi HÃ?Â¥kan,

Thank you *very* much for your comments on the Triple K Luger magazines. IÃ¢??ve been buying Megar magazines, but they can be hard to find. IÃ¢??ll have to order a half dozen or so Triple K magazines

One can never have too many spare magazines

Best regards,

Kyrie

06-03-2001, 03:04 PM

Both Mauser Parabellum extractors & ejectors will interchange with the PO8. As when mixing several manufacturer's parts minor fitting may be required in DWMs & Erfurts, etc. At the moment, I've forgotten whidh parts house purchases Mauser's Pararabellum parts, but I bought all that Interarms had in stock and they are new. It's very difficult to find well used Parabellums here in US, at a price that I can justify parting them out.

06-02-2001, 11:48 PM	#1
HÃ?Â¥kan Spuhr User Join Date: Jun 2002 Location: Sweden Posts: 282 Thanks: 0 Thanked 0 Times in 0 Posts	Gunparts As we are rebuild lugers for target shooting we do often need certain gunparts as extractors and ejectors. We have earlyer orderd such from Gunparts corporation and just recived cast ****. Parts that made just to make money on and not to shot with. I don't mind if the parts is new as its only for target guns, but they have to be good. Do anyone here have any ideas, is here someone that make their own extractors and ejectors? I will maybe have the extractors made up, and replace the little hook that always breaks with a small ring, like the swiss extractors. But this is an expensive way. I have also orderd new manufactured rear toggles with the sightbase for a Bomar sight in one piece with the toggle. Those toggles are also greatly imporve both in steelquality ( worst swedish tooolsteel) and thicker material where the toggles normally crack. Regards HÃ?Â¥kan http://www.vapensmedjan.com

06-03-2001, 12:43 AM	#2
Thor User Join Date: Jun 2002 Location: Rio Rancho, New Mexico Posts: 4,583 Thanks: 958 Thanked 970 Times in 276 Posts	Re: Gunparts Tom Heller can supply you with original parts! I have bought lots of spare parts from him and they are quality parts! ~Thor~

06-03-2001, 03:19 AM	#3
Patrick User Join Date: Jul 2002 Posts: 241 Thanks: 0 Thanked 1 Time in 1 Post	Re: Gunparts H. At the recent Berlin gun show, I saw a rack full of ex-VoPo rear toggle links that had, I suppose, been made in ex-East Germany. And also about twenty half-finished extruded mags (I now wish I had bought some). You can get quite good extractors here - BUT - not all of them fit without having to be touched up a bit. Patrick

06-03-2001, 07:00 AM	#4
tom h Guest Posts: n/a	Re: EXTRACTORS & EJECTORS I agree that most large firms that just advertise one price for these items, is probably going to send you either a new repro or an original with a grade 2 finish, unless you are extreemly lucky. That's why my prices vary based on type and quality. Extractors: original externally numbered military @$40 exc, $30 vg, unnumbered unissued spares $50. Internally numbered DWM commericals @$50 exc. Also have new unissued Mauser Parabellum (same loop design as M29 Swiss) @$60 or with Swiss proof $75. Also have Erfurt or Simson proofed ones in this price range. New repros that require a lot of fitting @$25. Same basic prices & types will apply to ejectors, but these of course are all unnumbered.

06-03-2001, 11:40 AM	#5
HÃ?Â¥kan Spuhr User Join Date: Jun 2002 Location: Sweden Posts: 282 Thanks: 0 Thanked 0 Times in 0 Posts	Re: EXTRACTORS & EJECTORS Thanks a lot for the responses. Will the Mauser parabellum extractors with loop fit a P08? I don't care so much about the condition of the parts as the quality, though we are rebuilding and rebluing all of them anyway. About magazines I have been extremely happy with tripple K stainless mags, they have proved to work great in our guns. Regards HÃ?Â¥kan http://www.vapensmedjan.com

06-03-2001, 01:12 PM	#6
Kyrie User Join Date: Jun 2002 Posts: 757 Thanks: 0 Thanked 212 Times in 101 Posts	Thank you for the Magazine tip! Hi HÃ?Â¥kan, Thank you very much for your comments on the Triple K Luger magazines. IÃ¢??ve been buying Megar magazines, but they can be hard to find. IÃ¢??ll have to order a half dozen or so Triple K magazines One can never have too many spare magazines Best regards, Kyrie

06-03-2001, 03:04 PM	#7
tom h Guest Posts: n/a	Re: EXTRACTORS & EJECTORS Both Mauser Parabellum extractors & ejectors will interchange with the PO8. As when mixing several manufacturer's parts minor fitting may be required in DWMs & Erfurts, etc. At the moment, I've forgotten whidh parts house purchases Mauser's Pararabellum parts, but I bought all that Interarms had in stock and they are new. It's very difficult to find well used Parabellums here in US, at a price that I can justify parting them out.