ejecter re install side plate assembly

anchor24 · 07-21-2014, 08:08 AM

1914 eurfert took this luger apart to clean i am having trouble re installing ejecter also non matching #s luger am having trouble with side plate gun fires extracts ejects does not **** gun for next round i change side plate with club member works fine. i believe the frame is ww1 barrel ww2 are there a difference in the side plate thickness between ww1 ww2 side plate thank you for all your help

DavidJayUden · 07-21-2014, 08:21 AM

Search YouTube for ejector re-assembly details. Seems like you insert one end and then press it in as you move either fore, or aft, with thumb pressure. But it has been a long time.
Others will help you with the side plate issue.
dju

alanint · 07-21-2014, 08:22 AM

The rear of the ejector needs to be gently lifted in order to clear a small seating/locking protrusion on the frame.

The problem with the gun not resetting the firing pin is most likely related to the plunger at the end of the sear bar. make sure there is no debris around the sear and that the plunger moves freely. I have buffed the side of the plunger that faces farthest outward to make sure it both clears and resets the firing pin.

mrerick · 07-21-2014, 10:05 AM

Check the side plate to ensure that it is laying flat and level with the side of the receiver and frame.

This part was hand fit by armorers when it was installed. That's why it is uniquely numbered.

The one you're trying to use may require some fitting. I would not recommend that you try it yourself unless you have experience.

Marc

07-21-2014, 08:08 AM	#1
anchor24 User Join Date: Oct 2012 Posts: 6 Thanks: 1 Thanked 0 Times in 0 Posts	ejecter re install side plate assembly 1914 eurfert took this luger apart to clean i am having trouble re installing ejecter also non matching #s luger am having trouble with side plate gun fires extracts ejects does not **** gun for next round i change side plate with club member works fine. i believe the frame is ww1 barrel ww2 are there a difference in the side plate thickness between ww1 ww2 side plate thank you for all your help

07-21-2014, 10:05 AM	#4
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,925 Thanks: 1,377 Thanked 3,139 Times in 1,520 Posts	Check the side plate to ensure that it is laying flat and level with the side of the receiver and frame. This part was hand fit by armorers when it was installed. That's why it is uniquely numbered. The one you're trying to use may require some fitting. I would not recommend that you try it yourself unless you have experience. Marc __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

07-21-2014, 08:21 AM	#2
DavidJayUden Patron LugerForum Patron Join Date: Nov 2008 Posts: 4,047 Thanks: 578 Thanked 1,414 Times in 887 Posts	Search YouTube for ejector re-assembly details. Seems like you insert one end and then press it in as you move either fore, or aft, with thumb pressure. But it has been a long time. Others will help you with the side plate issue. dju

07-21-2014, 08:22 AM	#3
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,917 Times in 1,193 Posts	The rear of the ejector needs to be gently lifted in order to clear a small seating/locking protrusion on the frame. The problem with the gun not resetting the firing pin is most likely related to the plunger at the end of the sear bar. make sure there is no debris around the sear and that the plunger moves freely. I have buffed the side of the plunger that faces farthest outward to make sure it both clears and resets the firing pin.