C-96 holes

k98mike · 05-27-2019, 03:14 PM

I have a C-96 Mauser in 7.63. A few years ago When I bought it, I put 40 rounds through it, and while it functioned perfectly, many- or most of the ejected brass had black holes in the primers. The firing pin was undamaged. I didn't finish the box, and cleaned the pistol and put it back in the safe. (The ammo was PPU, the only 7.63 I could find on the internet. Since then I've asked a number of people, and gotten just as many different answers. The people on this forum seem very knowledgeable; I bet I'll get a good answer here. Thanks in advance for any replies.

gunnertwo · 05-27-2019, 04:55 PM

Probably a sign of over pressure. Lots of surplus com-bloc ammo is too hot for the C96. You should only use 7.63 Mauser ammo in those pistols.

G2

k98mike · 05-27-2019, 05:02 PM

The PPU box was labeled 7.63 Mauser, but being from Serbia, who knows? Are there other brands available that you know of?

DonVoigt · 05-27-2019, 05:07 PM

Pierced primers are caused by a too long firing pin, or one with a rough tip.
In a Broomhandle there should be a spring on the front of the firing pin to cushion the impact and retract the pin, if it is broken, short, or missing, it could contribute to a pierced primer.

High pressure does not cause a pierced primer; perhaps a flattened primer.

PPU ammo should be just fine; assuming your broomhandle is in proper condition and the headspace is correct.

gunnertwo · 05-27-2019, 05:09 PM

Here's a link to what I found on Ammoseek.com:

https://ammoseek.com/ammo/7.63x25mm-mauser

I'd still be careful and look for velocity ratings. You don't want to risk harming your pistol.

G2

05-27-2019, 03:14 PM	#1
k98mike User Join Date: Mar 2018 Location: Newnan, GA Posts: 141 Thanks: 280 Thanked 48 Times in 30 Posts	C-96 holes I have a C-96 Mauser in 7.63. A few years ago When I bought it, I put 40 rounds through it, and while it functioned perfectly, many- or most of the ejected brass had black holes in the primers. The firing pin was undamaged. I didn't finish the box, and cleaned the pistol and put it back in the safe. (The ammo was PPU, the only 7.63 I could find on the internet. Since then I've asked a number of people, and gotten just as many different answers. The people on this forum seem very knowledgeable; I bet I'll get a good answer here. Thanks in advance for any replies.

05-27-2019, 05:02 PM	#3
k98mike User Join Date: Mar 2018 Location: Newnan, GA Posts: 141 Thanks: 280 Thanked 48 Times in 30 Posts	Ppu The PPU box was labeled 7.63 Mauser, but being from Serbia, who knows? Are there other brands available that you know of?

05-27-2019, 05:07 PM	#4
DonVoigt User Join Date: Apr 2015 Location: near Charlotte NC Posts: 4,681 Thanks: 1,443 Thanked 4,354 Times in 2,041 Posts	Pierced primers are caused by a too long firing pin, or one with a rough tip. In a Broomhandle there should be a spring on the front of the firing pin to cushion the impact and retract the pin, if it is broken, short, or missing, it could contribute to a pierced primer. High pressure does not cause a pierced primer; perhaps a flattened primer. PPU ammo should be just fine; assuming your broomhandle is in proper condition and the headspace is correct. __________________ 03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie

05-27-2019, 04:55 PM	#2
gunnertwo User Join Date: Jan 2010 Location: Nampa, Idaho Posts: 626 Thanks: 839 Thanked 941 Times in 367 Posts	Probably a sign of over pressure. Lots of surplus com-bloc ammo is too hot for the C96. You should only use 7.63 Mauser ammo in those pistols. G2

05-27-2019, 05:09 PM	#5
gunnertwo User Join Date: Jan 2010 Location: Nampa, Idaho Posts: 626 Thanks: 839 Thanked 941 Times in 367 Posts	Here's a link to what I found on Ammoseek.com: https://ammoseek.com/ammo/7.63x25mm-mauser I'd still be careful and look for velocity ratings. You don't want to risk harming your pistol. G2