Opinions of this byf 41? 2M/M mags, holster/tool, capture papers

Garandy · 06-03-2012, 07:41 PM

Edward Tinker · 06-03-2012, 08:40 PM

I don't have any opinion than I stated on Jan Still's board, but be advised, 2M/M equals TWO matching magazines.

ed

alanint · 06-03-2012, 08:54 PM

Welcome!

You don't show the front of the lower frame serial number nor the bases of the two magazines. Although they may be "correct" for the gun, they are only matching if the numbers, (suffix in other cases) an proofs are all consistent. Also, the condition of the holster is worrysome as opposed to the balance of the pistol.

mrerick · 06-03-2012, 09:36 PM

I can't make out detail on the toggle train retention axle. Was it renumbered?

Garandy · 06-03-2012, 10:22 PM

It [toggle pin] wasnt renumbered, the mags are M/M, and its possible the holster was added, as its not mentioned in the capture paper text..

Garandy · 06-03-2012, 10:43 PM

Lower frame SN is 273..
Pin has something under it, but its still numbered 73..font the same?

DavidJayUden · 06-03-2012, 11:50 PM

Well it certainly hasn't seen much action.
I'm not concerned with the well used holster as I suspect that new guns were not necessarily issued with new holsters, so their level of wear need not be similar.
While someone may find fault with it, I'd be glad to have it in my safe...
dju

Garandy · 06-04-2012, 07:16 AM

Fonts? Note the pins 3 is flat headed, where the rest are rounded..there was something under it..being hardened steel, is it supposed to be different, or not Mauserwerke's manufacture?

alanint · 06-04-2012, 08:06 AM

The axle pin looks like a restamp to me..the three is much larger than the 7 and there is clearly another number under the 7 and perhaps as well under the 3. Axle pin stamps should be crisp and clear while this whole area looks very "busy" on your pin.

This is not a huge deal as you may find another, correct one.

06-03-2012, 07:41 PM	#1
Garandy New User Join Date: Jun 2012 Posts: 4 Thanks: 0 Thanked 1 Time in 1 Post	Opinions of this byf 41? 2M/M mags, holster/tool, capture papers

06-03-2012, 09:36 PM	#4
mrerick Super Moderator - Patron LugerForum Life Patron Join Date: Dec 2009 Location: Eastern North Carolina, USA Posts: 3,901 Thanks: 1,372 Thanked 3,094 Times in 1,503 Posts	I can't make out detail on the toggle train retention axle. Was it renumbered? __________________ Igitur si vis pacem, para bellum - - Therefore if you want peace, prepare for war.

06-03-2012, 08:40 PM	#2
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,916 Thanks: 1,995 Thanked 4,507 Times in 2,081 Posts	I don't have any opinion than I stated on Jan Still's board, but be advised, 2M/M equals TWO matching magazines. ed

06-03-2012, 08:54 PM	#3
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,916 Times in 1,192 Posts	Welcome! You don't show the front of the lower frame serial number nor the bases of the two magazines. Although they may be "correct" for the gun, they are only matching if the numbers, (suffix in other cases) an proofs are all consistent. Also, the condition of the holster is worrysome as opposed to the balance of the pistol.

06-03-2012, 10:22 PM	#5
Garandy New User Join Date: Jun 2012 Posts: 4 Thanks: 0 Thanked 1 Time in 1 Post	It [toggle pin] wasnt renumbered, the mags are M/M, and its possible the holster was added, as its not mentioned in the capture paper text..

06-03-2012, 10:43 PM	#6
Garandy New User Join Date: Jun 2012 Posts: 4 Thanks: 0 Thanked 1 Time in 1 Post	Lower frame SN is 273.. Pin has something under it, but its still numbered 73..font the same?

06-03-2012, 11:50 PM	#7
DavidJayUden Patron LugerForum Patron Join Date: Nov 2008 Posts: 4,047 Thanks: 578 Thanked 1,414 Times in 887 Posts	Well it certainly hasn't seen much action. I'm not concerned with the well used holster as I suspect that new guns were not necessarily issued with new holsters, so their level of wear need not be similar. While someone may find fault with it, I'd be glad to have it in my safe... dju

06-04-2012, 07:16 AM	#8
Garandy New User Join Date: Jun 2012 Posts: 4 Thanks: 0 Thanked 1 Time in 1 Post	Fonts? Note the pins 3 is flat headed, where the rest are rounded..there was something under it..being hardened steel, is it supposed to be different, or not Mauserwerke's manufacture?

06-04-2012, 08:06 AM	#9
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,916 Times in 1,192 Posts	The axle pin looks like a restamp to me..the three is much larger than the 7 and there is clearly another number under the 7 and perhaps as well under the 3. Axle pin stamps should be crisp and clear while this whole area looks very "busy" on your pin. This is not a huge deal as you may find another, correct one.