Shot my Borchardt replica today!

TennBill2 · 07-21-2011, 03:20 PM

After so much time having gone into building this, I was soooo anxious to fire it. I tried yesterday and had a misfire, having used an old 30 Mauser round. Today, I used a newly primed starline shell, loaded with 3.4 grains of the old Mauser powder and the original 30 Mauser bullet....86gr.(?). I used the shoulder stock because I was hoping to observe the action, though it was too fast. I would guess 3.0 to 3.3 would be adequate to cycle the action. Tests to be done later will tell. Of course, I have no clue as to the original Mauser cartridge's powder type. Anyway, it was a thrill to shoot this thing! I'm going to try several loads and try to set up my movie cam to hopefully capture the action.

lugerholsterrepair · 07-21-2011, 03:23 PM

Bill, For those who followed your thread on this ...it's fantastic news! Did the action cycle and feed another round?

alanint · 07-21-2011, 03:28 PM

Congratulations!!!

I'm really looking forward to close up photos of the finished pistol and stock!

Ron Wood · 07-21-2011, 03:46 PM

Wow! More photos, more photos, more photos, more photos....!

TennBill2 · 07-21-2011, 04:51 PM

Like Barney, I only issued myself ONE round! Even though I have an almost 4 acre lot, I live in a subdivision where they frown on discharging guns. Fortuitous as it was, we were having a thunderstorm and I opined a single 'crack' would go unnoticed! I need to order some bullets, probably from Buffalo Arms, to make up some cartridges. I've only a handful of the old Mauser rounds left and can't really measure the charge without knowing what was loaded in the originals. In retrospect, I did feel the recoil in my shoulder, though I noticed no muzzle climb. I guess, Ron, you're the only guy...here.. who has shot the original. I read somewhere, the originals had to be matched to the ammo at the factory so as to properly tweak the mainspring. I guess that's why the later (30's) ammo for both the Mauser and Borchardt may have led to comments the Borchordt had a nasty recoil. I'm using a double layer riveted, but the upper piece ends at the main pivot, at the rear of the springbox...if that's clear. Still, that gives a healthy cocking action!

lugerholsterrepair · 07-21-2011, 05:09 PM

Bill, I guess, Ron, you're the only guy...here.. who has shot the original. HAHA! Bill you must be sadly misinformed..Heck even my Wife Ellie has shot an original Borchardt..Her and 20 guys I know cause I handed the pistol to them personally. David Eash was kind enough to loan us a beautyful Borchardt, David Borjes loaded the ammunition we shot. This all took place at a private estate...our Host was Mr. George Anderson. A good time was had by all. Not many people can lay claim to fireing a genuine original Borchardt it's true...

The recoil was minimal..we fired with the stock attached. Dave had 2 power settings on his loads..one mild and one not so much mild. The first kicked the cartridge fairly close to the shooter. The more powerful loading kicked them some 10-12 feet to the rear.

I suspect the recoil is milder than a stocked Luger due to the spring type and weight of the Borchardt. I have fired untold rounds from stocked pistols and you will not see any appreciable muzzle rise ...even when fireing fast.

TennBill2 · 07-21-2011, 06:41 PM

In my relatively short time in the forum, Ron was the only one I was aware of by name. I'm sure the Borchardt 'party' was, indeed, a good time! As the price of an original seems to become astronomical, I'm guessing fewer and fewer will risk firing one. Since I've never seen one, or wrapped my hands around one.....let alone, shot one, I have only what you guys 'tell' me regarding how they handle. Nevertheless, the build has been an adventure. Kind of like being Herr Borchardt. I know a whole bunch of ways that DON'T work! Didn't Edison say that about the lightbulb? I have several stocked pistols also, don't shoot this stuff much. Look at 'em, clean them, handle them, wrap them up, lock 'em up............

07-21-2011, 03:20 PM	#1
TennBill2 RIP Join Date: Feb 2011 Posts: 101 Thanks: 0 Thanked 17 Times in 6 Posts	Shot my Borchardt replica today! After so much time having gone into building this, I was soooo anxious to fire it. I tried yesterday and had a misfire, having used an old 30 Mauser round. Today, I used a newly primed starline shell, loaded with 3.4 grains of the old Mauser powder and the original 30 Mauser bullet....86gr.(?). I used the shoulder stock because I was hoping to observe the action, though it was too fast. I would guess 3.0 to 3.3 would be adequate to cycle the action. Tests to be done later will tell. Of course, I have no clue as to the original Mauser cartridge's powder type. Anyway, it was a thrill to shoot this thing! I'm going to try several loads and try to set up my movie cam to hopefully capture the action. Attached Images

07-21-2011, 03:23 PM	#2
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,933 Thanked 3,124 Times in 1,434 Posts	Bill, For those who followed your thread on this ...it's fantastic news! Did the action cycle and feed another round? __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 lugerholsterrepair@earthlink.net 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

07-21-2011, 03:46 PM	#4
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 7,022 Thanks: 1,090 Thanked 5,178 Times in 1,703 Posts	Wow! More photos, more photos, more photos, more photos....! __________________ If it's made after 1918...it's a reproduction

07-21-2011, 04:51 PM	#5
TennBill2 RIP Join Date: Feb 2011 Posts: 101 Thanks: 0 Thanked 17 Times in 6 Posts	Barney Fife! Like Barney, I only issued myself ONE round! Even though I have an almost 4 acre lot, I live in a subdivision where they frown on discharging guns. Fortuitous as it was, we were having a thunderstorm and I opined a single 'crack' would go unnoticed! I need to order some bullets, probably from Buffalo Arms, to make up some cartridges. I've only a handful of the old Mauser rounds left and can't really measure the charge without knowing what was loaded in the originals. In retrospect, I did feel the recoil in my shoulder, though I noticed no muzzle climb. I guess, Ron, you're the only guy...here.. who has shot the original. I read somewhere, the originals had to be matched to the ammo at the factory so as to properly tweak the mainspring. I guess that's why the later (30's) ammo for both the Mauser and Borchardt may have led to comments the Borchordt had a nasty recoil. I'm using a double layer riveted, but the upper piece ends at the main pivot, at the rear of the springbox...if that's clear. Still, that gives a healthy cocking action!

07-21-2011, 05:09 PM	#6
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,933 Thanked 3,124 Times in 1,434 Posts	Bill, I guess, Ron, you're the only guy...here.. who has shot the original. HAHA! Bill you must be sadly misinformed..Heck even my Wife Ellie has shot an original Borchardt..Her and 20 guys I know cause I handed the pistol to them personally. David Eash was kind enough to loan us a beautyful Borchardt, David Borjes loaded the ammunition we shot. This all took place at a private estate...our Host was Mr. George Anderson. A good time was had by all. Not many people can lay claim to fireing a genuine original Borchardt it's true... The recoil was minimal..we fired with the stock attached. Dave had 2 power settings on his loads..one mild and one not so much mild. The first kicked the cartridge fairly close to the shooter. The more powerful loading kicked them some 10-12 feet to the rear. I suspect the recoil is milder than a stocked Luger due to the spring type and weight of the Borchardt. I have fired untold rounds from stocked pistols and you will not see any appreciable muzzle rise ...even when fireing fast. __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 lugerholsterrepair@earthlink.net 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

07-21-2011, 03:28 PM	#3
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,916 Times in 1,192 Posts	Congratulations!!! I'm really looking forward to close up photos of the finished pistol and stock!

07-21-2011, 06:41 PM	#7
TennBill2 RIP Join Date: Feb 2011 Posts: 101 Thanks: 0 Thanked 17 Times in 6 Posts	a good time........ In my relatively short time in the forum, Ron was the only one I was aware of by name. I'm sure the Borchardt 'party' was, indeed, a good time! As the price of an original seems to become astronomical, I'm guessing fewer and fewer will risk firing one. Since I've never seen one, or wrapped my hands around one.....let alone, shot one, I have only what you guys 'tell' me regarding how they handle. Nevertheless, the build has been an adventure. Kind of like being Herr Borchardt. I know a whole bunch of ways that DON'T work! Didn't Edison say that about the lightbulb? I have several stocked pistols also, don't shoot this stuff much. Look at 'em, clean them, handle them, wrap them up, lock 'em up............