9mm loads with Clays

GOATSNGUNS · 08-13-2014, 12:04 AM

I will be loading for a 1939 s/42 and would like to use Hodgdon clays. I am looking for a safe functioning load with 115 gr FMJ . I also have an older P-38 and would like to use the same loads. Comments, recommendations????

Thanks, Gary

cliffdropover1 · 08-13-2014, 02:47 AM

I had a Kimber Solo that no reload would work in. I found that 3.6 grains of Clays would work perfectly in this gun and felt surprisingly light. No signs of excessive pressure. Of course use any advice with caution. I am not responsible for this load. All I know is that it worked very well for me and proved to be remarkably accurate too. Forgot to mention this was for the 124 grain bullet only. I do believe this is the max load even though it felt light.

GOATSNGUNS · 08-16-2014, 12:48 AM

Loaded up 32 rounds of 9mm 115 gr. Win FMJ/HB with 3.5 gr. of clays with a COL of 1.170", using a light Lee factory crimp. Fired 16 in the PO8 and 16 in the P38. No signs of high pressure, but had numerous stove pipes and FTF in both guns. The primers all looked good, no pressure signs. I have two mags for the PO8 and one Mag for the P38, same results with both the PO8 mags. I did not have time to set up the chronograph but recoil was mild. I will have to duplicate these and fire over the chronograph before upping the charge weight. Any comments or suggestions would be greatly appreciated.

Thanks,
Gary

noylj · 09-02-2014, 07:00 PM

Your charges are slightly too light for your pistol.
Personal opinion only: Clays would not be amongst my first 20 powders I would select for 9x19. It, N310, and TiteGroup can show sudden pressure increases from one round to another even with all rounds using the same weight charges.
That being said, starting loads for Clays and 115gn jacketed bullets is 3.6-3.7gn, with a max load in two manuals of 3.9gn.
Personally, again, that is too small a range for me to play in.

Edward Tinker · 09-02-2014, 10:47 PM

No idea Gary, but continue to talk about reloading, I need to learn more

rhuff · 09-03-2014, 04:30 PM

Gary,

Of course, by running these rounds over a chrono, you will get a good idea of where you are with this loading. I have no experience with using Clays Powder, but according to my manuals, and what you describe, you are producing too soft of a recoil impulse for your handguns to function reliably....short stroking.

Your approach is the safest one, by starting out low and "sneaking up" on your loads watching for pressure signs. I hope that you will be able to find the combo of components that your handguns require. Keep us informed, and good luck.

kurusu · 09-22-2014, 01:18 PM

Quote:

Originally Posted by noylj

Your charges are slightly too light for your pistol.
Personal opinion only: Clays would not be amongst my first 20 powders I would select for 9x19. It, N310, and TiteGroup can show sudden pressure increases from one round to another even with all rounds using the same weight charges.
That being said, starting loads for Clays and 115gn jacketed bullets is 3.6-3.7gn, with a max load in two manuals of 3.9gn.
Personally, again, that is too small a range for me to play in.

Plus one for slower powders (N340 or Unique). It's very easy to go overboard with fast powders.

08-13-2014, 12:04 AM	#1
GOATSNGUNS User Join Date: Nov 2012 Location: Nortwest Arkansas Posts: 22 Thanks: 9 Thanked 0 Times in 0 Posts	9mm loads with Clays I will be loading for a 1939 s/42 and would like to use Hodgdon clays. I am looking for a safe functioning load with 115 gr FMJ . I also have an older P-38 and would like to use the same loads. Comments, recommendations???? Thanks, Gary Last edited by GOATSNGUNS; 08-14-2014 at 01:15 PM.

09-02-2014, 10:47 PM	#5
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,932 Thanks: 2,032 Thanked 4,528 Times in 2,091 Posts	No idea Gary, but continue to talk about reloading, I need to learn more __________________ Edward Tinker ************ Co-Author of Police Lugers - Co-Author of Simson Lugers Author of Veteran Bring Backs Vol I, Vol II, Vol III and Vol IV

08-13-2014, 02:47 AM	#2
cliffdropover1 User Join Date: Aug 2007 Location: Kentucky Posts: 65 Thanks: 1 Thanked 9 Times in 5 Posts	I had a Kimber Solo that no reload would work in. I found that 3.6 grains of Clays would work perfectly in this gun and felt surprisingly light. No signs of excessive pressure. Of course use any advice with caution. I am not responsible for this load. All I know is that it worked very well for me and proved to be remarkably accurate too. Forgot to mention this was for the 124 grain bullet only. I do believe this is the max load even though it felt light.

08-16-2014, 12:48 AM	#3
GOATSNGUNS User Join Date: Nov 2012 Location: Nortwest Arkansas Posts: 22 Thanks: 9 Thanked 0 Times in 0 Posts	Loaded up 32 rounds of 9mm 115 gr. Win FMJ/HB with 3.5 gr. of clays with a COL of 1.170", using a light Lee factory crimp. Fired 16 in the PO8 and 16 in the P38. No signs of high pressure, but had numerous stove pipes and FTF in both guns. The primers all looked good, no pressure signs. I have two mags for the PO8 and one Mag for the P38, same results with both the PO8 mags. I did not have time to set up the chronograph but recoil was mild. I will have to duplicate these and fire over the chronograph before upping the charge weight. Any comments or suggestions would be greatly appreciated. Thanks, Gary

09-02-2014, 07:00 PM	#4
noylj User Join Date: Mar 2013 Posts: 41 Thanks: 0 Thanked 13 Times in 12 Posts	Your charges are slightly too light for your pistol. Personal opinion only: Clays would not be amongst my first 20 powders I would select for 9x19. It, N310, and TiteGroup can show sudden pressure increases from one round to another even with all rounds using the same weight charges. That being said, starting loads for Clays and 115gn jacketed bullets is 3.6-3.7gn, with a max load in two manuals of 3.9gn. Personally, again, that is too small a range for me to play in.

09-03-2014, 04:30 PM	#6
rhuff Patron LugerForum Patron Join Date: Mar 2011 Location: Az. Posts: 2,291 Thanks: 2,709 Thanked 972 Times in 717 Posts	Gary, Of course, by running these rounds over a chrono, you will get a good idea of where you are with this loading. I have no experience with using Clays Powder, but according to my manuals, and what you describe, you are producing too soft of a recoil impulse for your handguns to function reliably....short stroking. Your approach is the safest one, by starting out low and "sneaking up" on your loads watching for pressure signs. I hope that you will be able to find the combo of components that your handguns require. Keep us informed, and good luck.