EG Breechblocks! Issues!

G.T. · 05-05-2023, 01:29 PM

Hi To all, I have quite a few EG post war made breechblocks, the are marked on the bottom with a part number, bo stamped or engraved, and another electro penciled on. Anyway, they look nice, and although you still need to fit the parts somewhat, they can be used, it would seem, as a nice replacement for the blown out blocks from past history. Well, it turns out, not so much!!!!

The problem with them is that they will strip a round from the mag and feed it anywhere from half to two thirds of the way into the chamber and then it will stop, SOLIDLY, and that's it, a tight jam? If you swap out an original toggle train, or original breechblock, it will work fine, kind of, sort of, eliminating the barreled receiver, feed ramp possibilities. Anyway, if any of you have run into this, please feel free to join in on the discussion! In the meantime, when my hands heal up from the toggle pulls, I will revisit

... best to all, til....lat'r....GT

Edward Tinker · 05-05-2023, 03:47 PM

I need to experiment - when they were selling them on ebay, I ended up buying 18 or 20 of them, only a handful are actual DDR made, the rest are imperial, weimar and mauser made

G.T. · 05-06-2023, 02:01 PM

Well, another sleepless night in the Hobbit Luger repair village!! Soooo, this morning, with calipers in hand, I went out to face my old nemisis, the dragon of ignorance! After a few minuted I decided that dimension difference couldn't be the issue, because even though there were variances, they were all well within the tolerances on the print, and identical to my few examples of original breechblocks! Soooo, I eliminated all the other possible culprits, extractor, firing pin,, ejector so it was just breechblock and feed ramp and any contact areas inbetween? I learned a long time ago that when trouble shooting, you need to eliminate variables, and focus on the task at hand, and so that's what I did! I turned my attention to the rim of the breechblock and decided that the inside part of the breechface rim was too sharp? So, out come the dremel with the most coarse polishing buff I could find and with that, polished the breechblock face enough to redius the sharp edge, but not change the dimensions overall.. To be truthfull, I didn't think it was the issue, but when I installed it into my test pistol, it worked great! So, they can be made to work? I might try to make a chamfer tool to just break the edge as I have quite a few of these problem child EG parts! But for now, we are aware and most of the elves are smiling...Hands are healing, and the next project is coming up! And then an afternoon of drum revision!

best to all, til....lat'r....GT

Edward Tinker · 05-06-2023, 02:18 PM

I wonder if a bunch of these EG parts were rejects and why they were left over?

G.T. · 05-06-2023, 03:01 PM

That's what I'm starting to think as well? They all seem to have something not quite right? But, I'm starting to think they may be usable down the road as we learn more about their shortcomings! I'm kind of excited to get to the range and see if they work dynamically? That's the real test.. Now I'm also going to go back and retry the initial receiver and see if it was just the EG breechblock the whole time????

I got my best elves on it... Hobbits couldn't quite figure it out!

More soon, best to you Ed, til.....lat'r....GT

Edward Tinker · 05-06-2023, 04:21 PM

I'll send you a couple of mine, I have 3 or 4 and can send all?
You measure and test with them?

Doubs · 05-06-2023, 04:59 PM

G.T., as you figure each one out and get it to work, you need a Crown/RC stamp to show that they're OK to use.

Ron Wood · 05-06-2023, 05:35 PM

Better, a Crown/GT stamp. Masterworks should be properly signed.
Ron

Doubs · 05-07-2023, 12:07 PM

Quote:

Originally Posted by Ron Wood

Better, a Crown/GT stamp. Masterworks should be properly signed. Ron

I like it. That's an even better idea.

05-05-2023, 01:29 PM	#1
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,506 Thanks: 1,318 Thanked 3,652 Times in 1,004 Posts	EG Breechblocks! Issues! Hi To all, I have quite a few EG post war made breechblocks, the are marked on the bottom with a part number, bo stamped or engraved, and another electro penciled on. Anyway, they look nice, and although you still need to fit the parts somewhat, they can be used, it would seem, as a nice replacement for the blown out blocks from past history. Well, it turns out, not so much!!!! The problem with them is that they will strip a round from the mag and feed it anywhere from half to two thirds of the way into the chamber and then it will stop, SOLIDLY, and that's it, a tight jam? If you swap out an original toggle train, or original breechblock, it will work fine, kind of, sort of, eliminating the barreled receiver, feed ramp possibilities. Anyway, if any of you have run into this, please feel free to join in on the discussion! In the meantime, when my hands heal up from the toggle pulls, I will revisit ... best to all, til....lat'r....GT

05-05-2023, 03:47 PM	#2
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,929 Thanks: 2,029 Thanked 4,527 Times in 2,090 Posts	I need to experiment - when they were selling them on ebay, I ended up buying 18 or 20 of them, only a handful are actual DDR made, the rest are imperial, weimar and mauser made __________________ Edward Tinker ************ Co-Author of Police Lugers - Co-Author of Simson Lugers Author of Veteran Bring Backs Vol I, Vol II, Vol III and Vol IV

05-06-2023, 02:01 PM	#3
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,506 Thanks: 1,318 Thanked 3,652 Times in 1,004 Posts	Following ahead of my self! Well, another sleepless night in the Hobbit Luger repair village!! Soooo, this morning, with calipers in hand, I went out to face my old nemisis, the dragon of ignorance! After a few minuted I decided that dimension difference couldn't be the issue, because even though there were variances, they were all well within the tolerances on the print, and identical to my few examples of original breechblocks! Soooo, I eliminated all the other possible culprits, extractor, firing pin,, ejector so it was just breechblock and feed ramp and any contact areas inbetween? I learned a long time ago that when trouble shooting, you need to eliminate variables, and focus on the task at hand, and so that's what I did! I turned my attention to the rim of the breechblock and decided that the inside part of the breechface rim was too sharp? So, out come the dremel with the most coarse polishing buff I could find and with that, polished the breechblock face enough to redius the sharp edge, but not change the dimensions overall.. To be truthfull, I didn't think it was the issue, but when I installed it into my test pistol, it worked great! So, they can be made to work? I might try to make a chamfer tool to just break the edge as I have quite a few of these problem child EG parts! But for now, we are aware and most of the elves are smiling...Hands are healing, and the next project is coming up! And then an afternoon of drum revision! best to all, til....lat'r....GT

05-06-2023, 03:01 PM	#5
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,506 Thanks: 1,318 Thanked 3,652 Times in 1,004 Posts	Hi Ed! That's what I'm starting to think as well? They all seem to have something not quite right? But, I'm starting to think they may be usable down the road as we learn more about their shortcomings! I'm kind of excited to get to the range and see if they work dynamically? That's the real test.. Now I'm also going to go back and retry the initial receiver and see if it was just the EG breechblock the whole time???? I got my best elves on it... Hobbits couldn't quite figure it out! More soon, best to you Ed, til.....lat'r....GT

05-06-2023, 05:35 PM	#8
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 7,019 Thanks: 1,090 Thanked 5,173 Times in 1,701 Posts	Better, a Crown/GT stamp. Masterworks should be properly signed. Ron __________________ If it's made after 1918...it's a reproduction

05-06-2023, 02:18 PM	#4
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,929 Thanks: 2,029 Thanked 4,527 Times in 2,090 Posts	I wonder if a bunch of these EG parts were rejects and why they were left over?

05-06-2023, 04:21 PM	#6
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,929 Thanks: 2,029 Thanked 4,527 Times in 2,090 Posts	I'll send you a couple of mine, I have 3 or 4 and can send all? You measure and test with them?

05-06-2023, 04:59 PM	#7
Doubs User Join Date: Jun 2002 Location: Byron, Georgia Posts: 1,696 Thanks: 792 Thanked 1,679 Times in 552 Posts	G.T., as you figure each one out and get it to work, you need a Crown/RC stamp to show that they're OK to use.