GB Auction Luger Carbine

aldo35 · 02-26-2015, 06:56 PM

GB has a nice looking Carbine for sale at #370080030 Starting price is $9999.

spacecoast · 02-26-2015, 08:11 PM

http://www.gunbroker.com/Auction/Vie...Item=470080030

No stock and quite a bit of wear on the grips, but I know very little about these.

Here are some others for comparison - http://www.simpsonltd.com/advanced_s...tion=1&x=0&y=0

The hole in the back of the receiver was likely not there to start.

Ben M. · 02-27-2015, 12:25 PM

hole is at back of frame. not receiver

sheepherder · 02-27-2015, 12:45 PM

Quote:

Originally Posted by spacecoast

http://www.gunbroker.com/Auction/Vie...Item=470080030

Thanks for tracking it down!

Looking at pic #8 (the closeup of the hole), that is a fairly pitted area...Lanyard loop & frame area around hole...

spacecoast · 02-27-2015, 01:47 PM

Quote:

hole is at back of frame. not receiver

You're correct of course, my bad.

cirelaw · 02-27-2015, 02:43 PM

A mystery hole!! Sergio nice work!!

cirelaw · 02-27-2015, 02:58 PM

PS! I would needs pictures of the insides and behind the grips! "Rust Never Sleeps" Eric

Lugerdoc · 03-02-2015, 11:25 AM

I've seen similarly located holes in other pre 1914 lugers (without stock lug) for centering a non factory type stock that attached to the lanyard loop. TH

ithacaartist · 03-02-2015, 05:52 PM

Quote:

Originally Posted by Lugerdoc

I've seen similarly located holes in other pre 1914 lugers (without stock lug) for centering a non factory type stock that attached to the lanyard loop. TH

Interesting, Tom. I can see, also, that there are two small horizontal grooves--one on each side--on the back end, just above the lanyard loop. I'd wager that these are the bearing areas against which the stock was tightened. Whether they occurred from simple wear, in interaction with such an apparatus, or were filed in, to locate the stock vertically...? The lanyard loop appears to have short legs in this pic--or, it may simply be foreshortening due to camera angle...

One of my '06 AEs has a small tapped hole near the bottom of the back-strap, and it arrived with a knurl-headed screw installed there. An aftermarket or home-made butt-stock setup. I think also, was the inspiration for this tapping and screw.

02-26-2015, 06:56 PM	#1
aldo35 User Join Date: Jul 2010 Location: Northern GA Posts: 343 Thanks: 2,214 Thanked 146 Times in 76 Posts	GB Auction Luger Carbine GB has a nice looking Carbine for sale at #370080030 Starting price is $9999.

02-27-2015, 02:43 PM	#6
cirelaw Lifer Lifetime Forum Patron Join Date: Dec 2003 Location: PORT ST LUCIE, FLORIDA Posts: 12,216 Thanks: 6,209 Thanked 4,133 Times in 2,173 Posts	A mystery hole!! Sergio nice work!! Attached Thumbnails

02-26-2015, 08:11 PM	#2
spacecoast User Join Date: Dec 2013 Location: FL and PA Posts: 332 Thanks: 276 Thanked 243 Times in 109 Posts	http://www.gunbroker.com/Auction/Vie...Item=470080030 No stock and quite a bit of wear on the grips, but I know very little about these. Here are some others for comparison - http://www.simpsonltd.com/advanced_s...tion=1&x=0&y=0 The hole in the back of the receiver was likely not there to start.

02-27-2015, 12:25 PM	#3
Ben M. User Join Date: Dec 2009 Location: Retired to Naples, FL. Posts: 488 Thanks: 87 Thanked 123 Times in 83 Posts	hole is at back of frame. not receiver

02-27-2015, 02:58 PM	#7
cirelaw Lifer Lifetime Forum Patron Join Date: Dec 2003 Location: PORT ST LUCIE, FLORIDA Posts: 12,216 Thanks: 6,209 Thanked 4,133 Times in 2,173 Posts	PS! I would needs pictures of the insides and behind the grips! "Rust Never Sleeps" Eric

03-02-2015, 11:25 AM	#8
Lugerdoc Patron LugerForum Patron Join Date: Jun 2002 Location: POB 398 St.Charles,MO. 63302 Posts: 5,089 Thanks: 6 Thanked 736 Times in 483 Posts	I've seen similarly located holes in other pre 1914 lugers (without stock lug) for centering a non factory type stock that attached to the lanyard loop. TH __________________ Tom Heller POB 398 ST.Charles, MO. 63302 Tel 636-447-3006 lugerdoc@charter.net