![]() |
my profile |
register |
faq |
search upload photo | donate | calendar |
|
|
|
|
#1 |
|
User
Join Date: Feb 2009
Location: Cave Creek
Posts: 347
Thanks: 72
Thanked 276 Times in 111 Posts
|
As a Machinist, I use dial calipers a LOT. I also reload and have a "Lyman" stainless steel caliper just for that. Calipers are perfect for reloading issues. I certainly DON'T use them for grinding a crankshaft or honing a cylinder bore when accurate readings to .0001" (a tenth of a thousandth) are required.
Of the dozens of dial calipers I've used (and it doesn't matter if Starrett or something Chinese), I often re-check my zero, as it seems as they wear, the needle will loose it's press fit on the pinion shaft and move slightly when the caliper is opened and closed quickly. In a low stress environment like reloading slowly opening and closing the jaws is more doable .I also like using the case gages for checking re-loads before boxing them, however, they only check case sizing NOT COAL. Recently came across these my employer got in a box of supplies he bought from an estate; https://www.topbrass-inc.com/collect...12832996851765 You get instant feedback regarding min/max SAMMI Specs for a caliber. |
|
|
|
|
|
#2 |
|
User
Join Date: Feb 2009
Location: Cave Creek
Posts: 347
Thanks: 72
Thanked 276 Times in 111 Posts
|
Maybe I complicate things here for you by adding this. I don't re-load for pistol, just precision high power centerfire rifle. Knowing how far the bullet "jumps" into the rifling is critical for load development. If the rifle is magazine fed, what will just fit into the mag is usually the limit unless rds are single loaded by hand.
I use this gage by Hornady to determine this dimension; https://www.bing.com/videos/search?q...3&&FORM=VDRVRV |
|
|
|
| The following member says Thank You to calibrator for your post: |
|
|
#3 | |
|
User
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,753
Thanks: 849
Thanked 1,827 Times in 601 Posts
|
Quote:
https://www.midsouthshooterssupply.c...in-storage-box |
|
|
|
|
|
|
#4 |
|
Patron
LugerForum Patron Join Date: Mar 2011
Location: Az.
Posts: 2,316
Thanks: 2,768
Thanked 1,000 Times in 735 Posts
|
For my handloading I keep both a set of digital calipers and dial calipers handy on my bench. Either will get the job done. I don't own a plastic caliper, and likely will never purchase one. Maybe I am just too "old school"!!
__________________
Need DWM breechblock #21 |
|
|
|
|
|
#5 |
|
User
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
|
The caliper shown in the pictures is brand new but over 30 years old. It's Swiss made (45.00 $ CND) bought aound the time i got my reloading press. I can tell that it feels very thight altough it's slides smoothly. And you have to put much pressure to measure (instructions). I don't know if my caliper will endure but, with what I've read here, I'll take great care when I use it. Thank you all.
|
|
|
|
|
|
#6 |
|
User
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
|
Thanks for the link. I'll have to check in that a little bit more.
|
|
|
|
|
|
#7 |
|
User
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
|
Thank you again. I've read on the subject a little and find it very inetresting. Eventually, I'll be relaoding for my 7 mm Rem Mag; which is why I bought a reloading press in the first place.
|
|
|
|
|
|
#8 |
|
User
Join Date: Nov 2020
Location: Québec, Canada
Posts: 36
Thanks: 57
Thanked 15 Times in 7 Posts
|
Thanks for your knowledge and the link.
|
|
|
|
![]() |
| Tags |
| preps to start reloading |
| Thread Tools | |
| Display Modes | |
|
|