LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Repairs, Restoration & Refinishing

Reply
 
Thread Tools Display Modes
Unread 10-27-2020, 06:26 PM   #1
spangy
Lifer
Lifetime Forum
Patron
 
spangy's Avatar
 
Join Date: Sep 2020
Location: Winnipeg, Canada
Posts: 632
Thanks: 3,206
Thanked 1,068 Times in 437 Posts
Default

Quote:
Originally Posted by DonVoigt View Post
You should replace the damaged breechblock. the missing areas serve to retain and limit
motion of the extractor and are a likely source of your problem.

Breechblocks are not inexpensive, but important for function and safety.

GT can do this for you.
100% agree DV .... A long shot but make sure you have a fluted firing pin ... The non fluted is original, due to primer rupture and blow back that would destroy the firing pin and sometimes the toggle. They replaced them with a fluted pin that has a grove to allow gas to escape and this might have accounted for the original breech block damage if it occurred.
And having Dr.GT look @ it is an offer too good to refuse in my book .... good luck M8
spangy is offline   Reply With Quote
The following 2 members says Thank You to spangy for your post:
Unread 10-27-2020, 08:35 PM   #2
RWBlue01
User
 
Join Date: Oct 2020
Posts: 20
Thanks: 17
Thanked 8 Times in 5 Posts
Default

Quote:
Originally Posted by spangy View Post
100% agree DV .... A long shot but make sure you have a fluted firing pin ... The non fluted is original, due to primer rupture and blow back that would destroy the firing pin and sometimes the toggle. They replaced them with a fluted pin that has a grove to allow gas to escape and this might have accounted for the original breech block damage if it occurred.
And having Dr.GT look @ it is an offer too good to refuse in my book .... good luck M8
I have the flutted firing pin. Thanks

All this taking apart and putting together, I have gone from 15 minutes to less than 5. I feel like I should be speaking german.
RWBlue01 is offline   Reply With Quote
The following member says Thank You to RWBlue01 for your post:
Unread 10-29-2020, 02:50 PM   #3
DonVoigt
User
 
DonVoigt's Avatar
 
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,683
Thanks: 1,444
Thanked 4,358 Times in 2,042 Posts
Default

Quote:
Originally Posted by spangy View Post
They replaced them with a fluted pin that has a grove to allow gas to escape and this might have accounted for the original breech block damage if it occurred.
And having Dr.GT look @ it is an offer too good to refuse in my book .... good luck M8
Sprangy,
That is not the original or intended purpose of the grooves, they are there to collect gunk, dirt, trash and allow the striker to still function.
It is however often repeated "common knowledge" that is just not accurate.

This subject has been the focus of several threads, but if one simply observes the location and extent of the grooves, it is clear that there is nowhere for any trapped gas to go, even with the striker to its full rear position.
__________________
03man(Don Voigt); Luger student and collector.
Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie
DonVoigt is offline   Reply With Quote
The following 2 members says Thank You to DonVoigt for your post:
Unread 10-29-2020, 04:53 PM   #4
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,753
Thanks: 849
Thanked 1,827 Times in 601 Posts
Default

Quote:
Originally Posted by DonVoigt View Post
Sprangy,
That is not the original or intended purpose of the grooves, they are there to collect gunk, dirt, trash and allow the striker to still function.
It is however often repeated "common knowledge" that is just not accurate.

This subject has been the focus of several threads, but if one simply observes the location and extent of the grooves, it is clear that there is nowhere for any trapped gas to go, even with the striker to its full rear position.
Don, while Gortz & Sturgess acknowledge that the flutes had the primary purpose of allowing oil and dirt to flow past the firing pin to prevent build up of residue that reduced the impact force of the firing pin, they also point out that the flutes do, in fact, allow gasses from a punctured primer to bleed off and reduce the rearward thrust of the firing pin that would otherwise cause damage if the firing pin was not fluted. G&S point out that it is a benefit but, as you state, not the purpose for which the flutes were intended. G&S red books, pages 1115 & 1116.
Doubs is offline   Reply With Quote
The following 2 members says Thank You to Doubs for your post:
Unread 10-31-2020, 11:20 PM   #5
DonVoigt
User
 
DonVoigt's Avatar
 
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,683
Thanks: 1,444
Thanked 4,358 Times in 2,042 Posts
Default

Quote:
Originally Posted by Doubs View Post
Don, while Gortz & Sturgess acknowledge that the flutes had the primary purpose of allowing oil and dirt to flow past the firing pin to prevent build up of residue that reduced the impact force of the firing pin, they also point out that the flutes do, in fact, allow gasses from a punctured primer to bleed off and reduce the rearward thrust of the firing pin that would otherwise cause damage if the firing pin was not fluted. G&S point out that it is a benefit but, as you state, not the purpose for which the flutes were intended. G&S red books, pages 1115 & 1116.
Doubs,
I know G&S "say" that, but it is a physical impossibility.
"They" got that statement wrong; it just is not physically possible, there is no where for the gas to escape to!

Marc,
The reference to the fluted, or gapped alignment disc shown in the drawing for the rifle bolt is an entirely different situation, and those channels do lead to an "expansion" area and eventually to the outside of the bolt.

Carefully observe the length of the grooves in the luger striker, and how far they extend, and find where the closest gas "escape" route is- the two do not intersect.
There is a slight possibility that some grooves cut by hand, when an old style striker was modified to include the grooves, "Might" be cut deep enough, and long enough, and in the correct alignment with the sear tab opening to "connect" just a bit-
But that condition is only met if all three requirements were met by accident !

Such a co-incidence was not intended and is not observed in machine/jigged production strikers.

I know the presence of the grooves just begs for the answer to be "gas management", but it just is not so.

Just an addition note, the Finns added a "real" gas escape hole in the bottom of their breech blocks, that hole is far enough forward to allow gas to escape.
Swiss strikers have a flat milled into the front and rear bearing surfaces of the striker to allow gas to pass along the length of the striker and exit the breech block.

Both of these later techniques/modifications do serve to allow gas to escape from the front of the striker in event of a pierced primer.

Attached Images
File Type: jpg 2018-07-07 15.46.59.jpg (126.5 KB, 1939 views)
File Type: jpg 20190428_191134.jpg (139.1 KB, 2039 views)
__________________
03man(Don Voigt); Luger student and collector.
Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie
DonVoigt is offline   Reply With Quote
The following 8 members says Thank You to DonVoigt for your post:
Unread 11-01-2020, 05:32 PM   #6
Doubs
User
 
Doubs's Avatar
 
Join Date: Jun 2002
Location: Byron, Georgia
Posts: 1,753
Thanks: 849
Thanked 1,827 Times in 601 Posts
Default

Quote:
Originally Posted by DonVoigt View Post
Doubs, I know G&S "say" that, but it is a physical impossibility. "They" got that statement wrong; it just is not physically possible, there is no where for the gas to escape to!

Don, I understand. It's somewhat surprising that the flutes weren't extended past the collar to allow gases from a ruptured primer to escape. I've actually had a FP keeper shear the small lug off when a primer ruptured. I've often wondered if the keeper was made of softer metal for that very purpose.

I also once owned a Finnish M23 that had been modified with a hole in the breechblock to allow gas to escape. A logical and good idea IMO.
Doubs is offline   Reply With Quote
The following 3 members says Thank You to Doubs for your post:
Unread 11-02-2020, 05:56 AM   #7
kurusu
User
 
Join Date: Sep 2007
Posts: 1,225
Thanks: 2,679
Thanked 930 Times in 509 Posts
Default

Quote:
Originally Posted by DonVoigt View Post
Doubs,
I know G&S "say" that, but it is a physical impossibility.
"They" got that statement wrong; it just is not physically possible, there is no where for the gas to escape to!
I'm sorry to say but I don't agree with you. There is indeed a way for the gas to escape. It's from the side cut of the breech block.



Mind you that you only need to relief enough pressure to prevent the firing pin to act as a piston and go full force backwards. And you know what? It works.
kurusu is offline   Reply With Quote
The following member says Thank You to kurusu for your post:
Unread 10-29-2020, 05:53 PM   #8
spangy
Lifer
Lifetime Forum
Patron
 
spangy's Avatar
 
Join Date: Sep 2020
Location: Winnipeg, Canada
Posts: 632
Thanks: 3,206
Thanked 1,068 Times in 437 Posts
Default

Quote:
Originally Posted by DonVoigt View Post
Sprangy,
That is not the original or intended purpose of the grooves, they are there to collect gunk, dirt, trash and allow the striker to still function.
It is however often repeated "common knowledge" that is just not accurate.
Thanks DV & Doubs ... you know I knew that ... I have read exactly what you said elsewhere but sometimes my 70 year old brain misfires and I don't always remember These days I often can't remember anything past the last 24 Hrs. ... a combination of old age and the drugs I have to take for chronic pain.

John Walter (The Luger Book p.116) notes that the fluted firing pin was patented by Georg Luger as early as 1893 (DRP 78,406; DRP 90,433) as a method to keep striker-chambers clear of fouling.

Also as we are talking about a 1940 P08 Army Mauser its my understanding that it would have been manufactured with a fluted firing pin anyway as the fluted design was instituted in 1934. Having said that we can't know that the firing pin may have been replaced with a non fluted design in some other repair cycle.

so much to know ... so little time.
spangy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:21 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2026, Lugerforum.com