LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Shooting and Reloading

Reply
 
Thread Tools Display Modes
Old 03-22-2019, 10:33 AM   #1
Sieger
User
 
Sieger's Avatar
 
Join Date: Jul 2003
Location: New York, NY
Posts: 1,579
Thanks: 2,154
Thanked 402 Times in 251 Posts
Default

Quote:
Originally Posted by Kiwi View Post
Part II.
Forgot to mention in prior post my appreciation for Sieger's post on O.A.L. I measured the Previ cartridges at 1.146 a little shorter than Spec 1.175. I loaded mine to as close to Spec as I could measure with my vernier 1.172.


Off to the range with 5 rounds loaded with Herco 4.8 to see if it cycles, and a two sets of 3 SR7625 loads going down from the successful 4.2 of last week.

Results:-
The Herco produced a 1.5 by 0.5 group with holes overlapping.
The SR7625 loaded with 4.0 did not feed well and did not group well
With 3.8 did not feed well and also had a FTE

Takeaways – more Herco to come and will try 5.0 as 4.8 is very light compared to factory.
Will try the SR7625 at 4.5 for accuracy.

So much fun
Kiwi,

It is good to see my practical advice being used as such. Thanks!

If I were you, I would stick with the Herco powder, as is seems to be in the perfect medium/slow burning range preferred by both 7.65 and 9mm Lugers.

Is the 4.8 grain load you listed the minimum load that will hold open your action upon firing? If so, with a full magazine of
8 rounds, latter up your test charges 1/10 of a grain at a time until you reach minimum group size, or, out run your springs (I'm guessing the range to be 4.8 to about 5.6 grains of Herco).

Hope this helps!!


Sieger

Last edited by Sieger; 03-29-2019 at 05:10 PM.
Sieger is offline   Reply With Quote
Old 03-22-2019, 12:14 PM   #2
Kiwi
User
 
Kiwi's Avatar
 
Join Date: Mar 2019
Location: Wrong side of the Delaware river
Posts: 343
Thanks: 247
Thanked 493 Times in 194 Posts
Default

Sieger,

Thank you for your response

Not sure if the 4.8 is the minimum. I originally calculated 5.8, loaded them and they shot fine.
The 4.8 was a reading error on the scale. I was going to just unload using the bullet puller but decided to try them on the basis that the worst that would happen is a FTE or fail to cycle. I was surprised at how well they did. So Herco does work from 4.8 to 5.8 with good grouping.

The reasons to persist with SR 7625 is the burn rate is the same as Unique, I have a couple of tins of it and the only other cartridge I use if for is the .380 PPK/S which I do not shoot a lot of, so I would like to use it. Also the 7625 is a very fine powder that is consistent through a powder measure, most of the Hercules/Alliant powders are flakes with powder measure variations such that I throw low and top with a trickler.

Decision will ultimately be on group size and Herco is winning at this point
Kiwi is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:53 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2026, Lugerforum.com