LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > Luger Discussion Forums > Luger Accessories

Reply
 
Thread Tools Display Modes
Unread 01-19-2019, 08:29 PM   #1
Bill_in_VA
Lifer
Lifetime Forum
Patron
 
Bill_in_VA's Avatar
 
Join Date: Nov 2013
Location: Southwest Virginia
Posts: 417
Thanks: 846
Thanked 660 Times in 232 Posts
Default

So I had a chance to 25 rounds through the Numrich trommel. The follower stuck when I removed the loader and the first round tumbled out, so really I tested it with 24 rounds. I used a 4” 1915 DWM as my testing platform. The first three or four rounds loaded, fired, extracted/ejected, reloaded as expected. With the remaining rounds each shot would fire and eject but the toggle would hang open and not chamber the next round. A sharp smack or quick tug on the toggle would strip the round, chamber, fire, and eject, but again the toggle would hang open and not strip the next round. It wasn’t the hold open since a smack on top the toggle or removing the trommel caused the toggle to snap shut. I’m thinking the bottom of the bolt could be dragging on the feedlips. It could, however, also be the fact the my test platform was nickle plated. I’ll try a different pistol next go ‘round. I think shooting it a few more times might wear it in.
__________________
John 8:32


reive (riːv) vb (Military) (intr) dialect Scot and Northern English to go on a plundering raid
[variant of reave]
ˈreiver n e.g., " Some view the Border Reivers as loveable rogues."
Bill_in_VA is offline   Reply With Quote
Unread 01-19-2019, 10:15 PM   #2
G.T.
Lifer
Lifetime Forum
Patron
 
Join Date: Jun 2002
Location: Chandler Arizona
Posts: 3,550
Thanks: 1,361
Thanked 3,779 Times in 1,028 Posts
Default sluggish drum!

Hi Bill, it could certainly be dragging on the breechblock underside... but, try this first....Best if you can try another Luger as well... Field strip the luger, remove the firing pin, spring and retainer... Load the drum up with 25 rounds and cycle them thru by hand at the bench or range certainly while keeping the muzzle pointed in a safe direction... I use dummy rounds, and totally recommend only dummy rounds! But with care, you can find the issue using actual loaded rounds... AGAIN! It is then/now a loaded gun, and even with the firing pin removed, anything can happen!!!! Super careful with no one around!!! It should work at the bench just as well as shooting it... If you want me to send test dummy rounds to you, I will do so … Let me know, standing by... best to you, til...lat'r….GT

BTW, the problem may be the drum is too low, or too high in the Luger, one jams the bullet on the feed ramp (low), one drags on the feedlips(high)... but the fact that a bullet is always there means the drum is advancing correctly, just dragging some where?... Also, with the drum unloaded, push the follower down about an inch, so the hold open doesn't engage, and cycle the toggle several times to see if you can feel and drag when empty? standing by!

BTW, it could still be the hold open in that the reinforcing fold on the right hand side of the mag tube at the top, can just touch the back of the hold open tab and it will just barely engage... a little Dremel action will clean it up... on either drum or hold open?...
G.T. is offline   Reply With Quote
The following member says Thank You to G.T. for your post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:40 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2026, Lugerforum.com