LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > Luger Discussion Forums > Luger Accessories

Reply
 
Thread Tools Display Modes
Old 01-18-2019, 07:35 AM   #1
Bill_in_VA
Lifer
Lifetime Forum
Patron
 
Bill_in_VA's Avatar
 
Join Date: Nov 2013
Location: Southwest Virginia
Posts: 417
Thanks: 846
Thanked 660 Times in 232 Posts
Default

Mine came yesterday. It’s a lot nicer quality than I was expecting (then again, for almost five bills it ought to be reasonably so.) It did, however, come pre-wound. Putting it side by side with a real Bing trommel it’s a pretty close copy. I tried it in one of my LP.08s and in a 1938 Mauser and it fit well. The loader feels pretty solid and works well too. It also fits a real Bing and an AEG trommel. Both the loader and the trommel have GT’s “stamp of approval.” Plans are to go shoot tomorrow so I’ll give it a field test but I’m not anticipating any problems. Now... I need to find that repro board stock of mine for tomorrow...
__________________
John 8:32


reive (riːv) vb (Military) (intr) dialect Scot and Northern English to go on a plundering raid
[variant of reave]
ˈreiver n e.g., " Some view the Border Reivers as loveable rogues."
Bill_in_VA is offline   Reply With Quote
The following member says Thank You to Bill_in_VA for your post:
Old 01-18-2019, 12:25 PM   #2
G.T.
Lifer
Lifetime Forum
Patron
 
Join Date: Jun 2002
Location: Chandler Arizona
Posts: 3,550
Thanks: 1,361
Thanked 3,779 Times in 1,028 Posts
Default loader spring locked!

Hi Bill, Have fun with your drum! The reason it is locked open from G.T. Specialties upon delivery, is that when the swing arm is unlocked and rotated to "weak?" the follower spring is fully tensioned and when shipped, tends to pop out the top causing the more faint of heart to return the drums untried!!! …..... It is ready to load and ammo recommendations are primarily WW 115 grain ball, maybe even better is Federal 124 grain std. ball? (the heaver bullet has a bit better energy pulse when cycling it the Luger?)
Most of all be careful! Any jams or malfunctions, clear the weapon first, address the issue later... Best to you Bill, til...lat'r...GT....
G.T. is offline   Reply With Quote
The following member says Thank You to G.T. for your post:
Old 01-18-2019, 02:05 PM   #3
G.T.
Lifer
Lifetime Forum
Patron
 
Join Date: Jun 2002
Location: Chandler Arizona
Posts: 3,550
Thanks: 1,361
Thanked 3,779 Times in 1,028 Posts
Default NUMRICH drum loading tool revisions!

When NUMRICH received the drums, the magazine catch notch was located approx. .080" too high, which in turn, means the drum sets too low in the Luger to effect proper ejection! (I know, me too, it took me 6 months and two cases of ammo to figure that one out!!!!) ... Anyway, one of the major operations in the revision is to weld up the mag. catch notch on the drum, (no small feat in it's self!) re-radius the front spine inside and out, and re-mill the notch in the proper location, same as an original...
Having done that, the loader has to have the stop ears at the top, formed upwards, so the magazine will index correctly, and snap into the loading tool! Soooo, it means, the loader will work on all NUMRICH drum that have been revised, and most all original drums, especially BING manufacture... I sometime also relieve the mag catch cross pin so it engages deeper and as a result, hold it more positively.. Bill has it pretty much nailed, I try to make them as close to original as possible.. Not perfect! But, I'd say it's an easy 95% of what an original is?... Just my opinion, mostly doing them so forum members have a little "Luger spice" in their shooting range bag! ... best to all, til….lat'r….GT.....
G.T. is offline   Reply With Quote
The following member says Thank You to G.T. for your post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:40 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2026, Lugerforum.com