LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Repairs, Restoration & Refinishing

Reply
 
Thread Tools Display Modes
Old 01-30-2018, 01:52 PM   #1
DonVoigt
User
 
DonVoigt's Avatar
 
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,683
Thanks: 1,444
Thanked 4,358 Times in 2,042 Posts
Default

Miles,
Since I built my "7shot" baby myself, I have been down this road. A few observations
that may help :
-there is not enough room for a double spring
-a shortened spring is just as "strong", but lacks the tension at the end of the stroke for closing
-all springs are not the same, I was fortunate enough to have a handfull of old, take off, or out springs to experiment with.
-You will just have to "play" with the spring/ammo combination; but it sounds like what you have is working well
-Yes, some impact at the rear is normal- I have seen it in many/most lugers and have seen many that are quite a bit worse than yours.

Short answer, if it feeds and cycles now, leave it alone; and don't stress over a little impact!

You could show a picture of the back of the frame where the toggle bears against the frame. This will help understand if the spring is really weak, or you have a parts length/space mismatch inside.
__________________
03man(Don Voigt); Luger student and collector.
Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie
DonVoigt is offline   Reply With Quote
The following member says Thank You to DonVoigt for your post:
Old 01-30-2018, 02:04 PM   #2
milesc2
User
 
milesc2's Avatar
 
Join Date: Dec 2016
Location: USA - Kansas City
Posts: 216
Thanks: 339
Thanked 266 Times in 67 Posts
Default

Don,

I think leaving it as is may be the best answer yet. Your right about the double spring setup. I just tried to make one with a C96 mainspring and came very close but there just wasn’t enough room.
Also did GT’s measurement test and have confirmed it’s the longest possible spring that can be installed.

Your last point got me thinking... Could a small amount of material be removed from the back of the breech block? It seems as if the parts coming into contact are hitting very slightly, just enough to leave a mark. Maybe if a little material was removed they wouldn’t touch?

I am not removing it myself again... It was a miracle I got it back together without scratching anything!!!

Here are the requested photos. Please ignore the fingerprints.

Best,
-Miles
Attached Images
File Type: jpg 816D3E99-EF03-4684-BD8C-9DA2F48CA5CD.jpg (110.4 KB, 870 views)
File Type: jpg F98A10C9-A46C-4B50-8378-A8474E53D954.jpg (78.3 KB, 881 views)
milesc2 is offline   Reply With Quote
Old 01-30-2018, 04:02 PM   #3
G.T.
Lifer
Lifetime Forum
Patron
 
Join Date: Jun 2002
Location: Chandler Arizona
Posts: 3,550
Thanks: 1,361
Thanked 3,779 Times in 1,028 Posts
Default interference issue?

Hi Miles! Hey, you might have an interference issue in that it is impacting inside while not reaching the stop on the rear toggle outside? check it without the mainspring for travel and clearance?
On the mainspring... there are many different wire diameter variations right in the Luger mainspring family! I've seen them from .0535" all the way to .0685" and I'm not sure what the Wolf springs are at the moment! But, if you haven't an interference issue, then you need to measure the main spring wire size and go up a few thousands, with all else being relatively equal, you should be able to cure the issue?... ... I have some used take out springs that you can have to play with, just need to know wire dia. so we have a benchmark to start with?.... best to all, and Hi Don & Rick .... With these two guys on the hunt, and picking up the scent, the best dogs are definitely running!! best to all, til....lat'r....GT
G.T. is offline   Reply With Quote
The following member says Thank You to G.T. for your post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:36 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2026, Lugerforum.com