LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Shooting and Reloading

Reply
 
Thread Tools Display Modes
Old 07-26-2017, 10:45 AM   #1
Norme
Always A
Lifetime Forum
Patron
 
Norme's Avatar
 
Join Date: Jul 2009
Location: Colorado
Posts: 2,417
Thanks: 226
Thanked 2,607 Times in 933 Posts
Default

I would use a Phillips screwdriver and tap it out from the muzzle end.
Norm
Norme is offline   Reply With Quote
Old 07-26-2017, 05:47 PM   #2
DonVoigt
User
 
DonVoigt's Avatar
 
Join Date: Apr 2015
Location: near Charlotte NC
Posts: 4,683
Thanks: 1,444
Thanked 4,358 Times in 2,042 Posts
Default

Quote:
Originally Posted by Norme View Post
I would use a Phillips screwdriver and tap it out from the muzzle end.
Norm
Norm,
normally I would not contradict you, but to use a phillips or any screw driver or any pointed object, will only serve to expand the bullet more firmly into the rifling.

A flat rod is the way to go.

One might get buy with it if the bullet is only "slightly" stuck, but this one has already been beat on with a stick. The OP may have to resort to a pilot drill before he is done.

Rich,
don't even say that in jest, someone will think you are serious.

Chickenthief,
If one is absolutely positive there is only one bullet in the barrel, maybe- but once you make a recommendation you "own" the result.
__________________
03man(Don Voigt); Luger student and collector.
Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie
DonVoigt is offline   Reply With Quote
The following member says Thank You to DonVoigt for your post:
Old 07-26-2017, 06:23 PM   #3
gunbugs
Lifetime Forum
Patron
 
gunbugs's Avatar
 
Join Date: Sep 2013
Location: Fairbanks, Alaska. Home of the best moose.
Posts: 685
Thanks: 375
Thanked 1,232 Times in 416 Posts
Default

Over the years I've removed many a stuck bullet from the bores of rifles and pistols. (About 30 years as a full time gunsmith.)DO NOT use wood. Use aluminum, brass or steel, ONE PIECE rods that are near bore diameter, and do not protrude from the bore more than about 6" from the end you are going to tap on. Spray some of your favorite oil in the bore from the end the bullet will travel through, usually the chamber end, if it was a squib. Clamp the barrel firmly in a padded vise. Now insert the rod and bring it up against the projectile, hold it firmly, and give it a good strike with you favorite brass mallet. 1 or 2 hits will usually do the job.
Wood is a VERY bad idea, as it will typically break up and lodge pieces around the nose of the bullet, making any further attempts much more difficult. DO NOT use wood, of any type.
gunbugs is offline   Reply With Quote
The following 2 members says Thank You to gunbugs for your post:
Old 07-26-2017, 08:02 PM   #4
ithacaartist
Twice a Lifer
Lifetime Forum
Patron
 
ithacaartist's Avatar
 
Join Date: Mar 2011
Location: Atop the highest hill in Schuyler County NY
Posts: 3,419
Thanks: 7,605
Thanked 2,672 Times in 1,403 Posts
Default

Quote:
Originally Posted by gunbugs View Post
DO NOT use wood. Use aluminum, brass or steel, ONE PIECE rods that are near bore diameter, and do not protrude from the bore more than about 6" from the end you are going to tap on... DO NOT use wood, of any type.
Doug, I'll buy that! I think the salient point we can all agree on is protection of the bore. So, any material of lesser hardness that will take a whack with a hammer, avoid making a bad situation worse by getting itself stuck or broken, and configured for a slick fit down the pipe should, plus lubricant, do the trick. Fashion a slip-on cap to keep the pounded end from digging up its face and you could use a dead blow hammer. And the cap will keep the end of the rod from being peened...

Quote:
Originally Posted by cirelaw View Post
Does it only happen with reloads or am I safe with the old white box?
Eric, although it's theoretically possible to encounter a WWB squibb round, the odds against one being loaded off-spec enough to cause problems make them safe for all practical/reasonable considerations. I'm thinking that they are probably quite good about quality control, considering that their product produces an explosion in a small appliance that is held basically in front of one's face. With your background, you could probably explain the liabilities and regulations better than I! Do-it-yourself ammo can be exquisitely precise...or the opposite. If a round with not enough powder makes it through the process, whether in the factory or personal workshop, there's your squibb. They sound odd when shot, so if it does, unload and check that bore if there's any doubt. Firing another round into the system with an obstructed barrel = very bad.
__________________
"... Liberty is the seed and soil, the air and light, the dew and rain of progress, love and joy."-- Robert Greene Ingersoll 1894
ithacaartist is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:21 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2026, Lugerforum.com