LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Repairs, Restoration & Refinishing

Reply
 
Thread Tools Display Modes
Old 04-04-2016, 10:55 PM   #1
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default Forearm Redux

I didn't like the 'curl' at the tip of my forearm, so I made another one. That makes a total of five forearms I've made, and except for a chip, this last one came out just the way I wanted. So, more pictures.

Quick & dirty rundown...

(1) Donor wood stock, a Steyr straight-pull.
(2) Milling the inletting for the forearm lug.
(3) Milling the slot for the brass inlay.



(4) Milling trigger guard cut.
(5) Milling scallops with 1/2" ball end mill.
(6) Milling bottom flat, up to curl.
(7) Two views of squared-off forearm.



(8) Rounding bottom of side with corner rounding end mill.
(9) Same on other side.
(10) Chamfering top sides with weird burr.
(11) Two views of rounded-off forearm.



(12) Modified fixtures used to hold forearm for milling.
(13) Milling brass inlay to size.
(14) Rounding ends of inlay.
(15) Drilling & counterboring inlay for attaching screws.



(16) Finished forearm and brass inlay.



This completes the long-barreled part of this project. All metal parts are either blued or strawed (or brass) and forearm is finished except for final sanding and treating with BLO.

On to the next part!
__________________
I like my coffee the
way I like my women...
...Cold and bitter...

Last edited by sheepherder; 04-05-2016 at 10:53 PM.
sheepherder is offline   Reply With Quote
The following 3 members says Thank You to sheepherder for your post:
Old 04-05-2016, 11:04 PM   #2
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default The Buttstock

When I dug out my sales receipt from 1992, it was for a 1917 Luger. So, it could have been for a Luger carbine. I have both a 13" and a 16" barreled receiver for this Luger, so here's the period buttstock for it.

Finding a buttstock was very frustrating. I wanted a '1902 style' profile but all I could find were '1920 style' repros or duplicates. So, I ended up getting a used semi-finished 1920 style and sectioning & gluing it to look like a 1902 style.

(1) Buttstock as received from eBay seller.
(2) Milling a .060" thick x 10mm Walnut 'popsicle stick' for stock iron groove, both top & bottom.
(3) Popsicle sticks glued in & being milled to fit iron.
(4) Milling butt flat, and at an angle like 1902.



(5), (6), and (7) Milling lever reliefs in gooseneck with ball end mill.
(8) Stock iron fitted.



(9) Sawing eBay buttstock in half. EEK!!! What is this madman doing???
(10) Sawed pieces. Actually, two saw cuts, to create a ~5/16" taper/drop to the stock
(11) Milling sawn end of stock flat.
(12) Milling 3/8" slot for reinforcing wedge.



(13) Milling sawn end of gooseneck flat.
(14) Clamping stock pieces together to mark gooseneck for slot.
(15) Milling 3/8" slot in gooseneck.
(16) Pieces slotted and stacked to admire.



The slots have been milled at different angles, so the filler piece cab be wedge-shaped. Maked fitting easier.

(17) Milling a piece of Walnut down to .375".
(18) Clockwise - Spare piece of 3/8" Walnut; cardboard form; 3/8" wedge inserted between two sawn pieces.
(19) Wedge & two pieces glued together with Resorcinol glue and left clamped under mill quill.
(20) Glued buttstock 24 hours later, ready for shaping.

__________________
I like my coffee the
way I like my women...
...Cold and bitter...

Last edited by sheepherder; 04-07-2016 at 10:31 AM.
sheepherder is offline   Reply With Quote
The following member says Thank You to sheepherder for your post:
Old 04-06-2016, 12:04 AM   #3
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default

Glue has cured, excess wood of wedge has been band-sawed off, I'm now rough sanding the wedge and slots.

(21) Sanding the top of the wedge/slot. Bottom was next.
(22) Filling in some chips & low spots with the Resorcinol glue. Olle told me that Aircraft Spruce Co. had industrial-strength Resorcinol glue ("Cascophen") for use on aircraft and marine applications. The Resorcinol glue you get in hardware stores is watered-down and regulated to the point that it's no longer effective. This is the good stuff. Can be sanded, sawed, drilled, etc. When cured.
(23), (24) Rough sanding finished.



A buttplate is next. I could not find anything suitable. So I made one out of black Delrin. I love Delrin. It's lathe-turnable, millable, drillable, you can even tap/thread it. Nice hard Acetal plastic.

(25) Milling a piece of Delrin flat.
(26) Drilling attaching holes.
(27) Drilling the butt to match the buttplate holes.
(28) Rough belt-sanding the Delrin buttplate to shape.



(29) Buttplate fitted to stock; final marking of edges. Screws used are from an 1891 Argentine Mauser rifle. And, at this point, disaster struck. One of the old screws snapped the head off. Crystalline fracture. I couldn't grab onto the piece in the stock, I had to drill the piece out. This left a ragged hole, so I enlarged it and glued in a Walnut plug.
(30) 1/2" hole drilled for plug. Finished plug is in lathe in background.
(31) Resorcinol glue used to secure plug.
(32) Milling plug flat.



Following that setback, it was time to finish off the buttplate.

(33) Drilling the plug for the Mauser screw. I have several.
(34) Milling/thinning the buttplate to 5/16" thick.
(35) Rounding the edge with a 1/8" radius corner rounding router bit.
(36) Final sanding & fitting of buttplate to stock.



Time to finish sand and prep the forearm and buttstock for BLO. I followed the instructions given at Ironwood Designs for finishing their gunstocks (http://ironwooddesigns.com/IWDfinish.html). Five coats of Boiled Linseed Oil, let dry 24 hours, then buff.

(37) After first heavy coat of BLO. Waiting 15 mins then wipe excess off, then 4 thin coats, let dry 24 hrs.
(38) Finished stock/forearm after buffing.
(39) The finished and assembled Gonzo Luger long barreled carbine. It's no beauty, but it sure is...different...

__________________
I like my coffee the
way I like my women...
...Cold and bitter...

Last edited by sheepherder; 04-07-2016 at 10:36 AM.
sheepherder is offline   Reply With Quote
The following 2 members says Thank You to sheepherder for your post:
Old 04-06-2016, 12:06 AM   #4
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default

Here's a comparison pic of original '1920 style' duplicated stock as I got it (and fitted the stock iron) and compared to the finished stock before final sanding. It's not an exact match for a '1902 style' buttstock, but it'll do for now.



Here's a pic taken in the early hours of an April morning, outdoors, of the assembled finished 'carbine' with attached stock. All Gonzo - scalloped toggle knobs, 'cartridge counter' grips & modified Tomek magazines, Mauser rifle rear sight, and generally rough barn-job fabricating.

7.65 Parabellum caliber. I have no idea if it will even shoot. And I don't care.

__________________
I like my coffee the
way I like my women...
...Cold and bitter...
sheepherder is offline   Reply With Quote
The following 11 members says Thank You to sheepherder for your post:
Old 04-06-2016, 03:41 PM   #5
Jim Solomon
Lifer
Lifetime Forum
Patron
 
Join Date: Nov 2012
Location: Georgia
Posts: 199
Thanks: 700
Thanked 176 Times in 69 Posts
Default

Very nice work. Thanks for photos of the process. Quite creative.
Jim
__________________
Jim Solomon
dent2@frontiernet.net
Jim Solomon is offline   Reply With Quote
Old 04-30-2016, 07:24 PM   #6
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default Refurbing a 16" Barrel

This will be a rehash of what has gone before, but I decided to experiment on a couple of ideas I had, and take pictures so I would have a record.

I had originally made two barrels for this Gonzo project; after doing ~85% of the longer barrel, I decided to go in a different direction. So, I shelved the second barrel and started a third.

(1) The donor barrel - a Remington 700 barrel in 30-06 caliber.
(2) Turning down the barrel for the FN/Mauser carbine rear sight.
(3) Turning down the 'flange' that bears against the barrel extension ['receiver'].



Continuing operations on the Remington 30 cal barrel.

(4) Turning down the breech stub.
(5) Threading the breech stub.
(6) Cutting the stub to required length; turning relief.
(7) Final fitting the barrel extension to the threaded stub.



Chambering for 7.65 Parabellum.

(8, 9, 10) Cutting the chamber, 1/32" at a time.
(11) Final fitting the 7.65 Parabellum chamber.



Fabrication of the front sight base.

(12) Rectangular piece of steel drilled & tapped 1/2" x 28tpi and mounted in rotary indexing head to mill outer diameter.
(13) Milling the sides of the sight base flat.
(14) Chamfering the front of the base and milling the rear ramp.
(15) Turning down and threading the muzzle for the front sight base.



Now I'll mill the dovetail for the front sight blade.

(16) Cutting the dovetail.
(17) Milling the front sight blade from a piece of 3/8" steel bar.
(18) Blade has been dovetailed and is ready to be pressed in place.
(19) Blade has been squared to size and is being finish milled.



Test fitting the various pieces for fit and visual effect.

(20) Front sight screwed in place.
(21) Rear sight is a slip fit; it will be secured with screws later.
(22) Full length profile view.



Next will be making a keyhole spanner for the front sight base and a set of vise inserts for this barrel.
__________________
I like my coffee the
way I like my women...
...Cold and bitter...

Last edited by sheepherder; 05-01-2016 at 11:18 PM.
sheepherder is offline   Reply With Quote
The following 4 members says Thank You to sheepherder for your post:
Old 05-06-2016, 11:26 AM   #7
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default

Making the front sight base keyhole spanner, barrel vise inserts, and other small items.

(23) Boring a hole in a chunk of 7/16" aluminum plate.
(24) Milling the slot for ramp clearance.
(25) Spanner in use. Works great! By some stroke of luck (or divine intervention) the sight base is in exactly the right position for tightening to 12:00 position.
(26) Milling Patridge-style notch in rear sight leaf, to match squared front sight blade.



Vise inserts, made from aluminum round stock, 1 1/2" dia & 1 1/2" long.

(27) Faced insert being bored to ~.755", which is the diameter of the barrel just in front of the rear sight base.
(28) Sawing the finished vise insert in half. Cuts will be belt sanded smooth.
(29) A second vise insert is used for the front sight base, as shown in pic #25 above. An insert from another barrel project was the right size, so no other insert fabrication was required. Sight spanner, vise inserts, and receiver insert shown with torqued assembly. Bluing will be the final step.



Next will be a new, longer forearm to match this longer barrel.

(30) I have a piece of some kind of Walnut, 21" x 8" x 1 1/2". Has some defects [the X] but hey, it's what I gots.
(31) Slab has had a 1 3/4" x 9" piece cut off, decked top & bottom parallel, and barrel trench cut with a 5/8" ball end mill.
(32) Trimming ~.200" off each side. Bottom has had a similar amount milled off.
(33) Cutting the coves with a 1/2" ball end mill. Mounting holes were drilled first to hold the forearm to my mandrel/vise fixture.



Next up, I think, will be the bottom angled cut.
__________________
I like my coffee the
way I like my women...
...Cold and bitter...

Last edited by sheepherder; 05-17-2016 at 09:47 PM.
sheepherder is offline   Reply With Quote
The following 5 members says Thank You to sheepherder for your post:
Reply

Tags
blivet

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:49 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2026, Lugerforum.com