![]() |
my profile |
register |
faq |
search upload photo | donate | calendar |
|
|
|
|
#1 |
|
User
Join Date: Nov 2014
Posts: 33
Thanks: 1
Thanked 0 Times in 0 Posts
|
i have measured the oal of the cartridge and is 1.157.
|
|
|
|
|
|
#2 | |
|
Twice a Lifer
Lifetime Forum Patron Join Date: Mar 2011
Location: Atop the highest hill in Schuyler County NY
Posts: 3,419
Thanks: 7,605
Thanked 2,672 Times in 1,403 Posts
|
Quote:
Giuseppe, Too high a muzzle velocity = too much energy to cycle the pistol. The extra power goes into stressing the action of the gun as the rear toggle link slaps the rear of the frame and the breech block is slammed back against the inside of the link by the energy in excess of that needed to cycle. The advantage of hand loading is that the round can be tuned to a range of power that will dependably cycle the action without bottoming out its parts, one against another. That's why +P or +P+ or ammo marked NATO is not recommended. Standard power loads like Winchester White Box usually fall within the mechanically acceptable range.
__________________
"... Liberty is the seed and soil, the air and light, the dew and rain of progress, love and joy."-- Robert Greene Ingersoll 1894 |
|
|
|
|
| The following member says Thank You to ithacaartist for your post: |
|
|
#3 |
|
Patron
LugerForum Patron Join Date: Mar 2011
Location: Az.
Posts: 2,316
Thanks: 2,768
Thanked 1,000 Times in 735 Posts
|
I have no experience with the 9X21 cartridge. I deal with 9X17, 9X18, and 9X19 ammo. I handload the 9X17, and 9X19 brass. I can't seem to find much information in my reloading manuals concerning the specs for the 9X21 cartridge. I will do some more research concerning SAMMI specs on OAL and velocity for that round that you are required to shoot in your converted/rechambered Luger.
Added: From what I have found so far, the std. velocity for the 9X21 round is in the 12-1300fps range. Perhaps the box for your ammo will state it's factory velocity. The OAL is dependent on the bullet and it's profile, like is found in any factory ammo. The longer brass case allows the bullet to be seated deeper so that the OAL can mimic that of the 9mm(9X19) round of 1.169-1.171in. range. Your ammo has a shorter OAL, but still may function with a quality mag. |
|
|
|
|
|
#4 |
|
User
Join Date: Jul 2003
Location: New York, NY
Posts: 1,579
Thanks: 2,154
Thanked 402 Times in 251 Posts
|
Hi,
To reliably feed an 8 cartridge magazine, your OAL is much too short. Remembering that the original OAL for round nosed ammo, according to the original DWM specs., was 1.173 inches. For help on the OAL issue, please see my sticky on how to determine correct OAL when handloading a new type of bullet. Too "hot" of ammo will "out run" the springs of a Luger. Some choose to replace the recoil spring with a stronger one to help mitigate this. Frankly, if you handload your own 9X21 ammo, you should be able to find just the right load to properly operate your fine Luger pistol. Sieger Last edited by Sieger; 12-26-2014 at 12:02 AM. |
|
|
|
![]() |
| Thread Tools | |
| Display Modes | |
|
|