![]() |
my profile |
register |
faq |
search upload photo | donate | calendar |
|
|
|
|
#1 |
|
Lifer
Lifetime Forum Patron Join Date: Sep 2006
Location: Wichita, KS USA
Posts: 453
Thanks: 573
Thanked 96 Times in 53 Posts
|
fwiw - I think the grips at
https://www.gunpartscorp.com/ad/985140.htm are likely leftovers/culls from the 1970s mauser parabellum / interarms luger production like the production example currently offered at http://www.simpsonltd.com/product_in...84bb05051e0666 these grips have the angular V shape around the grip screws frame location perhaps a member who owns one of these can check the design / material used for these MP lugers with the counter in slot and comment thanks Bill |
|
|
|
| The following member says Thank You to lfid for your post: |
|
|
#2 |
|
User
Join Date: Oct 2013
Location: Florida/Penna
Posts: 898
Thanks: 893
Thanked 514 Times in 276 Posts
|
As quoted from ad. https://www.proxibid.com/asp/LotDeta...1416479274300#
The Powell Indicating Device consists of two components 1) A special left grip that has a small slot cut lengthwise down the grip with a small delicate metal strip attached to the backside that was covered with a 3 1/4 inch very fragile celluloid strip. The metal strip was inscribed with black numbers (1-7) running from the top to the bottom of the strip, that indicated the number of rounds remaining in the magazine. 2) The second part was the special cartridge counter magazine. This magazine, although similar to a standard wood base magazine, has been slotted on the left side of the body and was fitted with a special follower that had a small pin/indicator projecting on the left side. This small indicator pin has a single horizontal witness mark on top and the pin slides up and down under the celluloid strip as the rounds are fired, indicating how many cartridges were actually left in the magazine; a simple but very effective device. Last edited by hayhugh; 11-20-2014 at 06:37 AM. Reason: More info. |
|
|
|
|
|
#3 | |
|
Lifer
Lifetime Forum Patron Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
|
Quote:
That's not what I'm copying. This is the 1904 Dutch mod, right grip slotted. Different. ![]() [Sturgess & Gortz, pg 298] (Also much simpler.) ![]() But on the subject of the Powell Indicator, I had wondered why the 'indicator' was offset from the follower pin shaft...It's because the last round is way up inside the 'receiver' and the follower button shaft is no longer visible, so the pin is not used as the indicator; an offset pointer is installed. The Powell device is also limited to 7 rounds (1 - 7). Second pic shows 4 rds indicated but only two visible. Fascinating.
__________________
I like my coffee the way I like my women... ...Cold and bitter...
Last edited by sheepherder; 11-20-2014 at 09:38 AM. |
|
|
|
|
|
|
#4 |
|
User
Join Date: Aug 2013
Location: "Where the streets have no names"
Posts: 504
Thanks: 192
Thanked 200 Times in 136 Posts
|
very very cool Richard... thank you for sharing.
i wish i was as talented
|
|
|
|
|
|
#5 |
|
Lifer
Lifetime Forum Patron Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
|
I'm going ahead with a left-side 'cartridge counter' grip & magazine. I'm planning on using an extended follower pin/button for the indicator.
![]() I didn't have a spare Mec-Gar mag, so I ordered one from Greg Cote. I pressed out the base pins with an arbor press. There seems to be a correct way to do it, as shown in pic. After moving ~3/32", they popped right out. Magazine base and follower are plastic, so I'll have to make metal replacements. ![]() Locating the follower pin hole [cartridge indicator] in relation to the body, both 7-round [full] and one round [end of proposed slot]. 'Full' pin location is with top cartridge under tension from breechblock.
__________________
I like my coffee the way I like my women... ...Cold and bitter...
|
|
|
|
|
|
#6 |
|
Lifer
Lifetime Forum Patron Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
|
The magazine body needs to be securely clamped to mill out the slot, so I need an insert and outer relieved clamps (because of the ribs). I had a special mill cutter left over from a similar project [coff, coff] so I used that to contour the front of the insert. I used aluminum. The clamps are also aluminum, with 1/4" milled grooves for the rib clearance. A slot was milled in the clamp for end mill cutter clearance and observation. I chamfered it for better vision.
The magazine body can now be securely held and clamped for the milling of a 1/8" slot for the follower pin/indicator. All this for an operation that will take less than 5 minutes to perform...
__________________
I like my coffee the way I like my women... ...Cold and bitter...
Last edited by sheepherder; 12-20-2014 at 09:10 PM. |
|
|
|
| The following member says Thank You to sheepherder for your post: |
|
|
#7 |
|
Lifer
Lifetime Forum Patron Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
|
Boy, was I wrong about the five minutes!!!
![]() After spending two+ hours today, I have the mag body slotted! A long tedious chore, with one broken 1/8" 4-flute end mill. ![]() It just wouldn't take the feed. (BTW: Mec-Gar mags are not hardened). I ended up doing it all by hand, very slowly. ![]() I made a relief cut in my tube insert, then clamped the mag tube + insert in my 'sandwich' and indicated off the tube front for my slot. I used a #31 drill bit to zero my 1/8" end mill and sank it into the hole. Then it was one cut up the tube to open the slot up. After that, it was just climb and conventional milling each side to open it up a bit, as I'm planning on making my button pin 1/8". The first end mill broke off when I was ~5/8" into the power feed, as slow as my Chinese feed could be set. It left a jagged edge that cleaned up with subsequent cuts. A bit wider slot than I wanted, but them's the breaks [bad pun]. ![]() Next up is the follower.
__________________
I like my coffee the way I like my women... ...Cold and bitter...
|
|
|
|
![]() |
| Tags |
| blivet |
| Thread Tools | |
| Display Modes | |
|
|